It absolutely warms my heart to see Matthias not account for the thickness of his shim in the construction of his panel. It brings him back to earth here with me. And that is stated with absolutely NO disrespect! I watch his videos and dream of being half as accurate... innovative... and creative.
For those who find glass cutting aggravating, here's some things i learnt bashing my head through it a few times: 1. Find the best knife. 99.9% of the knives you find on the road are garbage. Even in reputable brand batches, you'll find garbage ones. It's all about finding the right one. I genuinely think i went through dozens of them until i managed to score the right knife. 2. Plan your cut. Kinda like in welding, do a ghost pass before the actual one. One, you wanna make sure you don't get stuck in something, two, that your brain has registered the motion so that: 3. Never stop mid cut, complete the cut in one smooth, clean cut. Never double back, never redo the line. 3a. If you had to stop, whatever the reason, find the termination of the previous cut, and start from that. 4. Practice. If you made a bad cut, the junk piece is your slice. Make that thing into tiny chips. It helps a lot. 5. Make sure the edges are scored through, start as cleanly as possible from the edge. If you don't have much luck with that (if you find that chipping occurs or the edge isn't cut right), you can use 3a in reverse. 6. Light scores = best cuts. 7. Don't bother with tapping all that much. Either use the weight of the glass to help you snap the extra piece or use the tiniest grain of sand under the cut to press the extra piece against on a flat, smooth surface. I've managed to go up to 1 cm thick glass using these. Perfectly smooth edges once i managed to get in the right groove.
Yeah, my grandfather used to cut LOTS of glass for his greenhouses. For him cutting a piece to fit took about a minute, and he never botched one up. And yeah, super sharp oiled cutter, and a single pass without much pressure at all. After you've done about a thousand of them over a decade or two you get pretty good at it.
I have horizontal slide windows and several window units. I find a well cut sheet of plywood and a little scrap foam work well but your solution is much nicer.
I did something similar back in 2007, although I wasn't clever enough to hook into the existing window latch mechanism. Instead, my frame was built as a U channel that, once installed, captured the window frame. The first year took a long time to install, but every spring and fall after, the procedure was much simpler. Mine were also able to be opened for fresh air on cool days.
@@AndyCollier Oh, you afraid of the boogie man as well? You enjoy following the silly useless request of your ranchers like good little herd member? Good for you brah...
@@bryphi77 Is it a submission muzzle or preventer of gov't facial recognition software? I'm getting my braindead crackpot conspiracy theories mixed up again.
Your solution is a lot more elegant than mine. I just used a 3/4" piece of plywood to fit both the window and cut a hole to slide the A/C unit in. Then cut more holes for side lights and flat mounted plexiglass with silicone and 1/4 round. Screwed the while thing into the window frame. Since the plywood was so thin the A/C unit kind of teetered a bit so I ran some small chain up to the soffits that I could secure the back end up and level it off. Just have to make sure it tips down slightly in the back or the moisture will run inside 🤔 😀
I love the process you went through to install this AC. I did something, somewhat similar with an AC that has the round ports that you close on a double hung window, except I had a casement window as well. I had not installed glass though, so I liked that upgrade. Mine was for a tenant though, one which wasn't paying rent either so it was just better that they leave so I could get the central AC fixed.
Great job, looks nice! 👍 For mounting glass, there is no need to hit with hammer near it. 😉 Old grandpa method is sliding hammer on glass without lifting it up.. Even I did it for multiple times when I changed glass and never break anything..
My home office is right under the roof and in the summer it can get quite toasty, especially with the computer running 8 hours a day. I've bought a single hose air conditioner from TCL. I know that it's really inefficient but it was all that was available. I don't have access to the window from the outside, since it's so high up, so I bought a Plexi glass sheet, cut it to size and cut a hole in it where I can plug in the hose. The whole contraption just sits right up against the rubber seal, held in place by some wooden blocks. That means that the mosquito net as well as the shutter still work perfectly fine and I can install the thing without having to mess with them. It works reasonably well, though it is extremely loud and inefficient by design.
I've been installing my ACS in a similar fashion for years. I either use layers of laminated cardboard or slices of styrofoam for the sides. I use plexiglass for the top of the units. I get them to cut it to shape when I pick it up. Not as fancy as the window frame you fabricated. Thanks for the content. Keep up the good work. בס'ד
@@wanders278 Matthias mentiones a solutions for a problem that occures with his saw. That problem would be milder if he used the safety equipment needed in factories. (For reasons!) He actively comments that he has this problem. So yes. He is passively calling for such comments. If he just showed the last cut, no one would comment about the riving knife either.
@@jBurn_ The saw isn't built to take a riving knife. It's funny that saw was built in the 2000s but can't take a riving knife, something a german saw from 1887 could!
I did something similar yet far less elegant when installing an AC into a friend's casement window, I just made a big panel that the unit fit, then moved all the hardware and hinges from the real window to my panel. It was easy to get it to fit, but no glass to look though unfortunately
I have sliders like you. I didn't want to put it in the window so I cut a hole in the wall with my 4" diamond saw and jackhammer and finished it out. It's much better, but a lot of work. The second floor required me to make a small scaffold. I just used double 2xs and plywood. Altogether it was about 3 days of work including patching/finishing inside for each a/c unit. I put them just under the window lintel and 6" from the edge of the window for structural reasons. edit; 3 units were about a week and a half to put in. I really should have specially ordered sleeve units for the particular wall but I was in a hurry and just took a stock ac unit. The sleeve was a little short, but I made it work. They are a little high on the wall but they have remote controls, so I never have to touch them. I just need to put some sort of damper outside on the top of the unit. It gets quite noisy when it rains hard.
Put the hardware in a Ziploc bag and tape it to the window, then when you want to reinsert the window, you can. You should have added a second pane with a gap between. Double pane is better.
@@sdspiveyI’ve been using magnets for hardware, and it works great. If there isn’t a place on whatever I need it for (ex the window), i have a magnetic dry erase board i can label
Hola Mathias . Estoy suscrito a su canal porque me encanta la gente creativa sin miedo a compartir su talento Aunque vivo en España y mi inglés es casi nulo, viéndole trabajar capto la idea La distancia y el idioma no son obstáculos para comprender sus genialidades Lo que más me sorprendió son sus máquinas de madera y últimamente lo veo más en otras cosas Me gustaría que diseñara y construyera una lijadora calibradora de rodillo con carro de desplazamiento automático Ahí lo dejo. Saludos desde España
I wish I had had the tools to do something like this when our central air died. It was a miserable two weeks before an HVAC tech could come out to fix it. The upper floor of our house hit 115°F at 90% relative humidity. We basically lived in the basement, and even down there it still got up to 92°F. Every window in the house is a casement, and even though I found some units that fit casement windows, no place locally stocked them. To special order one was going to take about as long as it took to fix the central AC.
Holy hell. I'm glad I live in Sweden. It might get up to 92°F in my media room on the summer with PC, TV on. Your "115°F at 90% relative humidity" sounds like a punishment.
@@matthiaswandel Yeah, that's primarily why I was trying to find one. Any drop in temperature however small would have been great though. I ended up buying a dehumidifier. Even though it made the basement a few degrees warmer, dropping the humidity from 90% down to about 40% made it so much more bearable.
I used to cool my whole house with one window ac unit, granted it was a larger one and permanently mounted in wall. It was in living room so I'd just run a couple fans blowing into the bedrooms. Cooled the whole place
I've wanted to do something similar even though I have a double hung window I'd like to get a much better seal to keep out bugs and the flimsy plastic accordion stuff is no good for that. Blue painters tape works, sorta. I run AC in my small office rather than the whole house since I work from home. No need to cool the rest of the house until the evening.
Easy, just close the window and throw the AC unit at it...done. Make sure the unit is tilted down at the outside at least 5 degrees, or you will wish you had. Seriously, it is important, otherwise it can leak inside, and often not initially but after a year or so, for some reason. Maybe crud buildup in the bottom of the cabinet? You make AC mounts like most people make furniture. I just cut out a piece of 3/4" plywood and chunked it in. Easier in aluminum single hungs.
Amazon purchase link: amzn.to/3NnDD3y Amazon discount code: 50AC002 (Valid thu May 22) Also available on Dreo's website: dreo.com/products/dreo-arctic-one
@@christopherinteriors6521 Are casement windows better than sliding? Casement windows are more energy-efficient than sliding windows. Since a sliding window has to have a flexible seal on the top and bottom runners of the window, it can never seal as tightly as a casement window. There will always be a bit of a gap on the top and bottom sash that allows some air through.
Sorry guys we seem to be a bit confused here from my original comment. I know what a casement window is, Most houses in England have them. It is the winder that opens it that I was curious about. Many thanks
ref: 3:00 For me it is just weird to see a single pane window. Would not a at least a double pane window make sense when you are going to cool the room inside?
I was wondering what camera and soundsetup you are using nowadays. There is an old video where you talked about your old 480p-1080p cameras and the sound was interesting back then as well. I would love to see a update on that. Lieben Gruß!
I like the confidence of a manufacturer to send a product to a random youtuber :) pr dept-"whats the worst that can happen" legal-"1.71 million people will see if our product sucks based on what he says" management- "even if you are right about this you are all fired. advertise on tictok or something next time"
Yeah, it almost hurts to see an AC (even worse, a window AC) get installed in a wooden frame without any measures to make it airtight, with a single pane piece of glass, and a thin piece of plywood. I guess that's what you get when energy is dirt cheap. Same goes for gas in the US, if they had European gas prices, those gas guzzlers would've been gone decades ago.
@@UhOhUmm Nah, the normal windows are definitely double pane, but it's more like that older double pane from the 90's that's 10 to 15mm thick. This home isn't that new, so it's to be expected. Personally I just wouldn't want to run an AC with such a large hole in the thermal barrier. Hell, I wouldn't even ever consider using a window unit, even if it did fit.
hehe, house isn't hot enough tomorrow, sun you just don't cut it, chuck some space heater in because... science!!! :) love your crazy Matthias, never change.
Question. Why Gorilla Glue? I remember a previous video testing a variety of wood glues for strength and such. Gorilla was not high on the list. Wondering why you used this time. For exterior usage? 🤔 Stay frosty Matthias. 🥶🥶😃
If you were taking out a window anyway to fit the ac unit, could you not have removed the panel that didn’t open to its left? That way you could have kept the opening window for fresh air if needed.
@@matthiaswandel as this had ever stopped you before. With your ingenuity I'm sure you can figure something out. There is a guy on TH-cam who already did it. I just xant think of his name right now
Wow, that’s a really good video but unfortunately I don’t have them type of power tools and at 62-year-old female I think I need something a little easier!
Air conditioners are most effective when they are installed as high as possible. I’m surprised that you as an engineer you didn’t take advantage of that fact.
There is practicality. also, no need to cool the air high in the room. The air blowing out of it mixes it just fine. I'm an engineer, so I don't have to follow stupid mantras.
It absolutely warms my heart to see Matthias not account for the thickness of his shim in the construction of his panel. It brings him back to earth here with me.
And that is stated with absolutely NO disrespect! I watch his videos and dream of being half as accurate... innovative... and creative.
Only Matthias would install an AC unit just so he could bring in space heaters to promote "Battle Of The Appliances!"
Global warming causing Canadians to install AC units? Better plug in some radiators at the same time speed the process along!
with an excel spreadsheet to show the data!
For those who find glass cutting aggravating, here's some things i learnt bashing my head through it a few times:
1. Find the best knife. 99.9% of the knives you find on the road are garbage. Even in reputable brand batches, you'll find garbage ones. It's all about finding the right one. I genuinely think i went through dozens of them until i managed to score the right knife.
2. Plan your cut. Kinda like in welding, do a ghost pass before the actual one. One, you wanna make sure you don't get stuck in something, two, that your brain has registered the motion so that:
3. Never stop mid cut, complete the cut in one smooth, clean cut. Never double back, never redo the line.
3a. If you had to stop, whatever the reason, find the termination of the previous cut, and start from that.
4. Practice. If you made a bad cut, the junk piece is your slice. Make that thing into tiny chips. It helps a lot.
5. Make sure the edges are scored through, start as cleanly as possible from the edge. If you don't have much luck with that (if you find that chipping occurs or the edge isn't cut right), you can use 3a in reverse.
6. Light scores = best cuts.
7. Don't bother with tapping all that much. Either use the weight of the glass to help you snap the extra piece or use the tiniest grain of sand under the cut to press the extra piece against on a flat, smooth surface.
I've managed to go up to 1 cm thick glass using these. Perfectly smooth edges once i managed to get in the right groove.
I must have been lucky, my first glass cutter I got from a guy that was selling off his stained glass setup.
Yeah, my grandfather used to cut LOTS of glass for his greenhouses. For him cutting a piece to fit took about a minute, and he never botched one up. And yeah, super sharp oiled cutter, and a single pass without much pressure at all. After you've done about a thousand of them over a decade or two you get pretty good at it.
I found oiling the cutter make a huge difference.
Dry scribe doesn’t break as sharp and sometimes even deviate from the scribe line.
Extremely well spoken regarding your perspective on cutting glass.
I guantee no one has put more work into installing a window ac unit! 🤣 I love it though! 👍
Where was this video last year when I needed it.
I appreciate how much you use construction and scrap lumber in your projects. It seems much more realistic of your typical at homes woodworker.
I’m glad you finally are willing to work with some companies. Makes for great content.
I have horizontal slide windows and several window units. I find a well cut sheet of plywood and a little scrap foam work well but your solution is much nicer.
My dad used rigid foam insulation which was great for efficiency.
This is what I did last summer. Looked like crap but it worked
Excellent editing! No need for me to speed the video up to watch (as I do on most videos). You are even working faster than Diresta!!
I did something similar back in 2007, although I wasn't clever enough to hook into the existing window latch mechanism. Instead, my frame was built as a U channel that, once installed, captured the window frame. The first year took a long time to install, but every spring and fall after, the procedure was much simpler. Mine were also able to be opened for fresh air on cool days.
well, I have another widow right next to it that I can open
Lol... at your submission muzzle.
@@bryphi77 Lol... at your stereotypical dudebro sunglasses profile photo.
@@AndyCollier Oh, you afraid of the boogie man as well? You enjoy following the silly useless request of your ranchers like good little herd member? Good for you brah...
@@bryphi77 Is it a submission muzzle or preventer of gov't facial recognition software? I'm getting my braindead crackpot conspiracy theories mixed up again.
Your solution is a lot more elegant than mine. I just used a 3/4" piece of plywood to fit both the window and cut a hole to slide the A/C unit in. Then cut more holes for side lights and flat mounted plexiglass with silicone and 1/4 round. Screwed the while thing into the window frame. Since the plywood was so thin the A/C unit kind of teetered a bit so I ran some small chain up to the soffits that I could secure the back end up and level it off. Just have to make sure it tips down slightly in the back or the moisture will run inside 🤔 😀
...and my neighbor gave me a 3/4" hose bib, so I built a house around it. Lol
Thanks for this. It gave me one solution to this problem.
That plywood at the top seems mostly hidden by the window blind, so yeah, seems better than having it just above the AC.
I loved this one. I'll try to remember that anti-pinch technique. Quickly kiln-dried lumber has so much stress in it.
I am always excited when I see Matthias has made an interesting home project. Thank you for another interesting build video.
This is why Mattias is so fun, you never know what you're gonna get.
I used to work for a plastics company. I made windows out of acrylic for our units.
That was quite an ambitious project.
I love the process you went through to install this AC. I did something, somewhat similar with an AC that has the round ports that you close on a double hung window, except I had a casement window as well. I had not installed glass though, so I liked that upgrade. Mine was for a tenant though, one which wasn't paying rent either so it was just better that they leave so I could get the central AC fixed.
A kindly carpenter that builds his own machines and lovingly constructs things... so that he can torture electronic devices. Such fun!
Great job, looks nice! 👍
For mounting glass, there is no need to hit with hammer near it. 😉 Old grandpa method is sliding hammer on glass without lifting it up.. Even I did it for multiple times when I changed glass and never break anything..
If you're serious about creating and maintaining a temperature difference between inside and outside; install double glazing.
My home office is right under the roof and in the summer it can get quite toasty, especially with the computer running 8 hours a day.
I've bought a single hose air conditioner from TCL. I know that it's really inefficient but it was all that was available. I don't have access to the window from the outside, since it's so high up, so I bought a Plexi glass sheet, cut it to size and cut a hole in it where I can plug in the hose.
The whole contraption just sits right up against the rubber seal, held in place by some wooden blocks.
That means that the mosquito net as well as the shutter still work perfectly fine and I can install the thing without having to mess with them.
It works reasonably well, though it is extremely loud and inefficient by design.
I can't really say why, but your timelapses are SO satisfying to watch.
I've been installing my ACS in a similar fashion for years. I either use layers of laminated cardboard or slices of styrofoam for the sides. I use plexiglass for the top of the units. I get them to cut it to shape when I pick it up. Not as fancy as the window frame you fabricated.
Thanks for the content.
Keep up the good work.
בס'ד
I see this type of thing done in North Philly a lot. Where lots of a special type of rigging goes on.
Installing your saw's riving knife would greatly reduce kickback/pinching.
Do you really want to start a discussion with Mathias about that? ;)
Who asked for this advice? Anyone?
@@wanders278 Matthias mentiones a solutions for a problem that occures with his saw. That problem would be milder if he used the safety equipment needed in factories. (For reasons!)
He actively comments that he has this problem. So yes. He is passively calling for such comments. If he just showed the last cut, no one would comment about the riving knife either.
@@jBurn_ The saw isn't built to take a riving knife. It's funny that saw was built in the 2000s but can't take a riving knife, something a german saw from 1887 could!
@@1873Winchester I've now watched the video about this saw. You are right! Quiet scary 🙄
I did something similar yet far less elegant when installing an AC into a friend's casement window, I just made a big panel that the unit fit, then moved all the hardware and hinges from the real window to my panel. It was easy to get it to fit, but no glass to look though unfortunately
Very skilled work!
Thanks Matthias ... and yes, I have to say it ... "very cool"!
Really neat idea with the pinch-cut fix!!!
I have sliders like you. I didn't want to put it in the window so I cut a hole in the wall with my 4" diamond saw and jackhammer and finished it out. It's much better, but a lot of work. The second floor required me to make a small scaffold. I just used double 2xs and plywood. Altogether it was about 3 days of work including patching/finishing inside for each a/c unit.
I put them just under the window lintel and 6" from the edge of the window for structural reasons.
edit; 3 units were about a week and a half to put in. I really should have specially ordered sleeve units for the particular wall but I was in a hurry and just took a stock ac unit. The sleeve was a little short, but I made it work. They are a little high on the wall but they have remote controls, so I never have to touch them. I just need to put some sort of damper outside on the top of the unit. It gets quite noisy when it rains hard.
Put the hardware in a Ziploc bag and tape it to the window, then when you want to reinsert the window, you can.
You should have added a second pane with a gap between. Double pane is better.
the plywood has 14 layers
Tape will leave a sticky residue later. But it is a good thought.
@@mckenziekeith7434 If you tape it to the top edge of the frame, it won't show and shouldn't matter much.
Perhaps staple the bag instead.
@@sdspiveyI’ve been using magnets for hardware, and it works great. If there isn’t a place on whatever I need it for (ex the window), i have a magnetic dry erase board i can label
Hola Mathias . Estoy suscrito a su canal porque me encanta la gente creativa sin miedo a compartir su talento
Aunque vivo en España y mi inglés es casi nulo, viéndole trabajar capto la idea
La distancia y el idioma no son obstáculos para comprender sus genialidades
Lo que más me sorprendió son sus máquinas de madera y últimamente lo veo más en otras cosas
Me gustaría que diseñara y construyera una lijadora calibradora de rodillo con carro de desplazamiento automático
Ahí lo dejo. Saludos desde España
I wish I had had the tools to do something like this when our central air died. It was a miserable two weeks before an HVAC tech could come out to fix it. The upper floor of our house hit 115°F at 90% relative humidity. We basically lived in the basement, and even down there it still got up to 92°F.
Every window in the house is a casement, and even though I found some units that fit casement windows, no place locally stocked them. To special order one was going to take about as long as it took to fix the central AC.
A window AC, while not able to cool down the whole house, can drop the humidity in the whole house quite substantially -- even a small window AC
Holy hell. I'm glad I live in Sweden. It might get up to 92°F in my media room on the summer with PC, TV on. Your "115°F at 90% relative humidity" sounds like a punishment.
@@matthiaswandel Yeah, that's primarily why I was trying to find one. Any drop in temperature however small would have been great though.
I ended up buying a dehumidifier. Even though it made the basement a few degrees warmer, dropping the humidity from 90% down to about 40% made it so much more bearable.
I used to cool my whole house with one window ac unit, granted it was a larger one and permanently mounted in wall. It was in living room so I'd just run a couple fans blowing into the bedrooms. Cooled the whole place
Excellent video! Thank you!
Always clear tutorial
Excelente instalación máster, de lo mejor como siempre, Dios te bendiga saludos desde cancun Quintana roo México 🇲🇽
By stacking 2 pieces together in the box joint jig you could cut your work in half.
I would like to see a frame that would let you securely install window AC in a vinyl replacement window without damaging the vinyl.
"After 25 trips to the shop..." Man, I felt that.
I wish I was as handy as you!
Might I ask why you'd install an AC, but re-use single pane glass above it? Seems like a weird combination. Is energy that cheap in Canada?
Doesn't make that much difference, at least not for a single window. A normal double pane window has an R value of 1.5-2. Single pane is around 1.
In summer it's hot anyways.
So why bother with insulation?
@@SuperDeinVadda I lost IQ just reading this comment
In winter the tempreature difference is often 30 degrees C. In summer, with AC, it's maybe 5 degrees. Just not worth it for summer only.
Yes Canada has very cheap electricity. Majority of our provinces use Hydro Electricity. We have lots of water…so far!
I've wanted to do something similar even though I have a double hung window
I'd like to get a much better seal to keep out bugs and the flimsy plastic accordion stuff is no good for that. Blue painters tape works, sorta.
I run AC in my small office rather than the whole house since I work from home. No need to cool the rest of the house until the evening.
Pretty nice work, Matthias! Nicely done! 😃
Stay safe there with your family! 🖖😊
And as always, I hate you Mathias…in a good way! You always find a way for things to work. Great work! From a friend in Quebec.
when fitting glass you put the hammer on the glass an slide it along the to nail the batten in
Easy, just close the window and throw the AC unit at it...done. Make sure the unit is tilted down at the outside at least 5 degrees, or you will wish you had. Seriously, it is important, otherwise it can leak inside, and often not initially but after a year or so, for some reason. Maybe crud buildup in the bottom of the cabinet?
You make AC mounts like most people make furniture. I just cut out a piece of 3/4" plywood and chunked it in. Easier in aluminum single hungs.
Added to Favorites
All was surprised by some of your ideals you come up with nice video
Sure you don't want to take on some adventures in stain glass making and replace that plywood piece?
Amazon purchase link: amzn.to/3NnDD3y
Amazon discount code: 50AC002 (Valid thu May 22)
Also available on Dreo's website:
dreo.com/products/dreo-arctic-one
Canadian link?
Is that the same link for the cardboard shim?
I miss the old property with the lake
Maybe a shim/wedge planting jig on the back of the table saw.
This is very impressive but what if one doesn't have the skill and specialized equipment to basically rebuild the house around an inexpensive AC unit?
I have never in my life seen a window that opens like that with a winder. Are they common in your country?
They are called casement windows and they are very common in Canada.
@@peggyt1243 I think the winder is pretty cool. It reminds me of my old cars.
@@christopherinteriors6521 Are casement windows better than sliding?
Casement windows are more energy-efficient than sliding windows. Since a sliding window has to have a flexible seal on the top and bottom runners of the window, it can never seal as tightly as a casement window. There will always be a bit of a gap on the top and bottom sash that allows some air through.
Sorry guys we seem to be a bit confused here from my original comment. I know what a casement window is, Most houses in England have them. It is the winder that opens it that I was curious about. Many thanks
ref: 3:00
For me it is just weird to see a single pane window. Would not a at least a double pane window make sense when you are going to cool the room inside?
for maybe 5 degrees temperature difference, not worth it. not like 25 degrees in the winter
Why not use a riving knife for the pinching?
Certified Boss💪
Wish they sold a kit for this
"...and joining the edges with box joints. Because that's what I do." 😂
Nice apron.
That's a lot work for a window unit. Should have just installed a mini split system.
I was wondering what camera and soundsetup you are using nowadays. There is an old video where you talked about your old 480p-1080p cameras and the sound was interesting back then as well. I would love to see a update on that. Lieben Gruß!
Would the house lose significant insulative capability since there is now a single-paned window?
The way those included seals work is usually garbage. I think maybe one big panel with a single cut out might have been a better way to go.
I like the confidence of a manufacturer to send a product to a random youtuber :) pr dept-"whats the worst that can happen" legal-"1.71 million people will see if our product sucks based on what he says" management- "even if you are right about this you are all fired. advertise on tictok or something next time"
It's so crazy to me that Canadians still have single pane windows in properties that aren't abandoned.
Yeah, it almost hurts to see an AC (even worse, a window AC) get installed in a wooden frame without any measures to make it airtight, with a single pane piece of glass, and a thin piece of plywood. I guess that's what you get when energy is dirt cheap. Same goes for gas in the US, if they had European gas prices, those gas guzzlers would've been gone decades ago.
its double pane, but the temporary window for the summer is only single pane
@@matthiaswandel oh it is? Looks so thin compared to the EU type window, guess it's the small frame giving the illusion
@@UhOhUmm Nah, the normal windows are definitely double pane, but it's more like that older double pane from the 90's that's 10 to 15mm thick. This home isn't that new, so it's to be expected. Personally I just wouldn't want to run an AC with such a large hole in the thermal barrier. Hell, I wouldn't even ever consider using a window unit, even if it did fit.
Never seen an in-window air conditioner here in NZ. Really weird. We only have split systems etc here.
Extremely popular here in North America. I’d say since the last 20 years now we’ve begun going into your type of A/C. They’re called mini splits.
That's right. I just replaced two window type AC units with 2 1 ton mini Split system s. What a difference. Much more efficient and quieter.
hehe, house isn't hot enough tomorrow, sun you just don't cut it, chuck some space heater in because... science!!! :) love your crazy Matthias, never change.
Sorry, wath brand is the orange drill? Thank you
Nice!
They are called double-hung windows. Single-hung windows exist, as well. (Correct names for the "vertical sliding" windows he was referring to.)
That slightly inclined screw in the glass - plywood division... IS THAT A POCKET HOLE?!
Were these pocket screws? Did I see pocket screws being used?
Do you leave this in year round?
“If at first you don’t succeed, you’re screwed” 😂
"if at first you don't succeed, you're screwed" 😂
It’s nice to see a window unit installed the right way. I see so many installed wrong or sloppy.
Are you going to paint it white to match?
He only have green paint😉😆
Oh God! Pocket screws at 3:36.
Technology Connections will have something to say about this airconditioning unit
i am fascinated about how thin your windows are. do you live in a hot place? and are you not worried someone will smash them to break in?
The glass I used was not an outside window
The concept of window A/C units is, I think, THE most American thing ever.
I think v8 engines and all you can eat restaurants are up there too.
Matthias isn't American.
It's a window AC unit, it's not that deep.
@@wanders278 So Canada isn't in America according to your geography?
I guess it's not just americans that don't knwo much about geography
@@matthiaswandel So what is that supposed to mean? Have you moved out of Canada or are you saying Canada isn't in the Americas anymore?
Matt it is time we need another marble machine.
Question. Why Gorilla Glue? I remember a previous video testing a variety of wood glues for strength and such. Gorilla was not high on the list. Wondering why you used this time. For exterior usage? 🤔 Stay frosty Matthias. 🥶🥶😃
I think he's trying to use up all the glue he bought for the video.
it wasn't gorilla glue
Did I just see Matthias install the centre support section with makeshift POCKET SCREWS??!
Function A+. Form, well never mind.
If you were taking out a window anyway to fit the ac unit, could you not have removed the panel that didn’t open to its left? That way you could have kept the opening window for fresh air if needed.
there's another panel that opens. And the non opening panel doesn't have a good way to take it out.
Get a riving knife for you saw. = no more Pinching the blade.
I dunno why American style saws don't have them. They are even mandatory in Germany lol
cause the older ones don't even have a mount for one
@@matthiaswandel as this had ever stopped you before.
With your ingenuity I'm sure you can figure something out.
There is a guy on TH-cam who already did it. I just xant think of his name right now
So you're saying when all you have is a box joint jig, everything looks like a box?
no. Just that it's so handy. I have other tools too!
Wow, that’s a really good video but unfortunately I don’t have them type of power tools and at 62-year-old female I think I need something a little easier!
Matthias Wandel Window and More!
why is the window open all the way i dont get that, closet to fit the ac save space
Cool
Are those single pane windows?
Air conditioners are most effective when they are installed as high as possible. I’m surprised that you as an engineer you didn’t take advantage of that fact.
There is practicality. also, no need to cool the air high in the room. The air blowing out of it mixes it just fine. I'm an engineer, so I don't have to follow stupid mantras.
wouldn't replacing the single pane glass with double pane would pay off in the long run?
How is it even humanly possible to live in Canada with single pane windows? My garage doesn't even have single pane windows!
In the summer heat, the temperature difference to outside is maye 5 degrees. Vs 25 or more in the winter. This window is only for the summer.
Haha, 1:05 box joint jig go brrr
👍👍👍