fabio sei bravissimo, ho acquistato una gommata bruder e vorrei come te usare dei servomotori, cercherò di ispirarmi al tuo video e ti ringrazio di cuore, bello e rilassante fare queste attività!!! buon 2025!!!
No It is a little slow because it is running at 3.7. But moves realistic (also because i set the accelerations on the taranis, and it is powerful. I could boost it to 6V and be much faster. Lets see if i find the time i can make a quick private video and share the linkhere in the comments
Gran bel progettino ...vorrei fare il Dumper 60H della Bruder ma non so da dove iniziare... mi aiuteresti??....bel video .. cmq lo parli bene in INGLESE ... Ciao da Fidenza PR
Ciao grazie Non conosco il 60H, modifico un po quel che mi capita in casa quindi non saprei aiutarti al volo. Faccio in inglese perchè sono un po argomenti di nicchia, mi vien da pensare che in inglese sia fruibile da piu gente
@@MakerFabio ciao Fabio fai bene a parlare in inglese...come dici tu è po'ius fruibile a tutti...anche io mi diletto nel modificare modellini...ho iniziato con le hotwheels....comunque ti è venuto proprio bene ... complimenti.. ciao ciao
@@MakerFabio Hi Maker, let me tell you my progress. I have managed to place its parameters and everything was fine except that when the servo reaches its end (this only happens in one direction) it returns to its axis very slowly after about 5 seconds. Another challenge is that one of the arms of the robot has 2 servos, I verified that these parameters are not valid for this arm with double servo, it goes crazy, I would like to know your opinion, if it would be possible to assign the function I am looking for to this arm double, by the other arms, I don't know what problem can occur so that in one of the senses, they return to their axis slowly. Sorry for the bad google translation.
@@Manuel-ti2zd not sure what happens. Probably your limiters are not working correcly, check the video at minute 6:16, those limit are clamping and avoiding exceeding 100% but also -100% So you have 2 different logical condition for max and min Copy each line (multiplaxer type is replace and not add). About 2 servos not working , there i have really no idea
@@MakerFabio Hello Maker, yes, everything is well configured, it only happens at one end and in all the servos, it reaches the end and after about 5 seconds, it returns very slowly to its axis. I can send you a video to any address.
Ciao Devi rubare un po con gli occhi, nelle varie scene, anche nei primi secondi quando scarico le macchinine, si vede di profilo, non saprei come mostrartelo, e non penso faró un video dedicato a quello. Se non bastasse, posso mandardi una ripresa con whatsapp, anche se non so come faremo a scambiarci i numeri qui in pubblico
@@MakerFabio You should make the video from 0, because there are many parameters that do not look like you included them and in the translation it is not explained
@@Manuel-ti2zd hi I see. I assumed how to add mixer inputs should be known, or at least there are many tutorials on this But you are also right , it would be handy to have it here directly Not sure if i ll do a video on that, i m more on the “trial and error” with the taranis, so not so good to teach eell. but i can try to publish my model file. Lets see in this days if i can download and post
Well done. I like getting cheap RC cars with missing controllers and converting them so they are repairable and usable. You have so many great ideas.
Ehehe, fixing cheap rc car is always a challenge. How much power can you put on them without destroying them.
My Guy, innovation at it's best.the Truth.
Thanks
Nice work!!
Thanks!
Very inspiring video.
Thanks
fabio sei bravissimo, ho acquistato una gommata bruder e vorrei come te usare dei servomotori, cercherò di ispirarmi al tuo video e ti ringrazio di cuore, bello e rilassante fare queste attività!!! buon 2025!!!
Very nice and simple
🔵🔵🔵👍👍👍😀😀😀🔵🔵🔵
Do you have a video of this Bruder to see how it performs?
🔵🔵🔵👍👍👍😀😀😀🔵🔵🔵
No
It is a little slow because it is running at 3.7. But moves realistic (also because i set the accelerations on the taranis, and it is powerful. I could boost it to 6V and be much faster.
Lets see if i find the time i can make a quick private video and share the linkhere in the comments
@@MakerFabio Thank you my friend
Good day. Good job. Can you please make a video how to make a servo a wheel drive motor. Please assist.
Gran bel progettino ...vorrei fare il Dumper 60H della Bruder ma non so da dove iniziare... mi aiuteresti??....bel video .. cmq lo parli bene in INGLESE ... Ciao da Fidenza PR
Ciao grazie
Non conosco il 60H, modifico un po quel che mi capita in casa quindi non saprei aiutarti al volo. Faccio in inglese perchè sono un po argomenti di nicchia, mi vien da pensare che in inglese sia fruibile da piu gente
@@MakerFabio ciao Fabio fai bene a parlare in inglese...come dici tu è po'ius fruibile a tutti...anche io mi diletto nel modificare modellini...ho iniziato con le hotwheels....comunque ti è venuto proprio bene ... complimenti.. ciao ciao
@@danielemulazzi1615 grazie
Hot wheels, veeeeramente piccole. Bravo
What servo did you use for the loader lifting arms...you stuck to the front..?
The big ones are always the same part number, link in the description
Hi Maker, is it possible that you can send me that model file and I can post it to my station?
Hi Manuel, I m traveling for a couple of days
I ll figure out how to share this WE
@@MakerFabio Hi Maker, let me tell you my progress. I have managed to place its parameters and everything was fine except that when the servo reaches its end (this only happens in one direction) it returns to its axis very slowly after about 5 seconds. Another challenge is that one of the arms of the robot has 2 servos, I verified that these parameters are not valid for this arm with double servo, it goes crazy, I would like to know your opinion, if it would be possible to assign the function I am looking for to this arm double, by the other arms, I don't know what problem can occur so that in one of the senses, they return to their axis slowly. Sorry for the bad google translation.
@@Manuel-ti2zd not sure what happens.
Probably your limiters are not working correcly, check the video at minute 6:16, those limit are clamping and avoiding exceeding 100% but also -100%
So you have 2 different logical condition for max and min
Copy each line (multiplaxer type is replace and not add). About 2 servos not working , there i have really no idea
@@MakerFabio Hello Maker, yes, everything is well configured, it only happens at one end and in all the servos, it reaches the end and after about 5 seconds, it returns very slowly to its axis. I can send you a video to any address.
Ciao, è possibile vedere nel dettaglio come hai fatto con il servo per alzare la pala?
Ciao
Devi rubare un po con gli occhi, nelle varie scene, anche nei primi secondi quando scarico le macchinine, si vede di profilo, non saprei come mostrartelo, e non penso faró un video dedicato a quello. Se non bastasse, posso mandardi una ripresa con whatsapp, anche se non so come faremo a scambiarci i numeri qui in pubblico
Buona sera... Scusami per il disturbo cortesemente e possibile avere i dettagli della elettronica che hai usato.... Grazie mille
Bella domanda, grazie
Ho messo la lista nella descrizione
grazie....
no se por que no empiezas el video de configuracion desde 0, tienes parametros introducidos, que no se de donde los has sacado
Sorry i speak only english and italian, not sure if i understand what you mean
@@MakerFabio You should make the video from 0, because there are many parameters that do not look like you included them and in the translation it is not explained
@@Manuel-ti2zd hi
I see. I assumed how to add mixer inputs should be known, or at least there are many tutorials on this
But you are also right , it would be handy to have it here directly
Not sure if i ll do a video on that, i m more on the “trial and error” with the taranis, so not so good to teach eell. but i can try to publish my model file. Lets see in this days if i can download and post
@@MakerFabioThank you very much, I am trying to move a 7 axis robot arm on a tank and your video of how to do it is fantastic. All the best
☝☝☝☝☝☝ very nice
Thanks
Why can't I save this video?
Hi, good question, i m not youtube expert and i didn t place any limitation
Ciao Fabio ma fai questi lavori anche a pagamento?
Ciao, no altrimenti diventa altro lavoro. Cosi invece faccio quel che mi ispira al momento
😀😀😀