{502} Why IGBT Burns Out After Replacement - IGBT Damaging Reasons
ฝัง
- เผยแพร่เมื่อ 7 ก.พ. 2025
- in this video i discussed Why IGBT Burns Out After Replacement - IGBT Damaging Reasons. the reasons and factors which are involved in IGBT failure, specially when we replace ibgt in induction cooker, inverter igbt welding machine, dc inverter ac outdoor unit boards, sewing machine inverter control board, top loading or front loading washing machine inverter boards, solar inverter boards, variable frequency drives (VFD). there are many factors involved in this scenario, material failure, how to select igbt specially VCE sat, power dissipation, zero crossing detection, resonant frequency, resonant coil, resonant capacitor, and teh gate drive components,
main root cause is the low quality standard of the components,
GBT Damaging Reasons / igbt failure,igbt short circuit after / igbt working principle / Igbt testing,igbt working animation / induction cooker repair igbt / induction cooker,induction cooker repair,haseeb electronics,inverter welding machine,how to repair igbt welding machine,insulated gate bipolar transistor,igbt short problem,igbt short circuit fault,igbt short circuit protection,igbt working,induction cooker working principle
![[436] How To Test IGBT / How to Check IGBT with Mulimeter / Why IGBT Damage](http://i.ytimg.com/vi/BDN8ayhhECo/mqdefault.jpg)
For better result:
1) Always check the ESR of the resonant capacitor and the internal insulation.
2) Remove all flux residue with a little brush and pure alcohol.
3) Apply electronic silicone to the solder pins of the IGBT and the driver on both sides of the PCB to prevent moisture in the air from activating the gate of the transistor.
it is really a great addition, i am personally thankful for a valuable guideline for my viewers
please accept my best regards
ما شاء الله انت كنز من المعلومات ...لقد فاجئتني عندما تكلمت باللغة العربية ....لم اجد ابدا بكل المحتوى العربي شخص بارع وضليع بالالكترونيك مثلك ..كم نحتاجك لو كان عندك قناة تتكلم فيها بالعربي ..
Mr. Mohamet is superb teacher
Thanks,good explanation. I've been losing igbts in inveters a lot nowadays from clients homes.
Thank you for explaining this is detail! I have also found it it frustrating to get reliable results when changing high power components. I always figured there was another component or "something". This video detail is very helpful for understanding what else is happening. Very well done as usual.
That is really very very informative now I understand what's the reason of burning MOSFETs and IGBT thank you so much for the very informative and easy understandable videos
Best regards from Philippines 🇵🇭
best regards and special thanks
Thanks lot for your genuine effort to share your valuable knowledge. My sincere blessings
One of the most important points that should be consider is: to recognize "Counterfeit" Components from the "Original" ones.
Counterfeit components make us "CONFUSE"
Your video was very helpful. I had changed in a mini welder the Igbt's because they burned out and one of the new one was always to hot 115 degrees Celsius one had approx 70kohm internal resistence and the other one approx 650kohm and that's why was to hot.
Thanks a lot, you make a wery good job.
wow that is really awesome
i am thankful for your valuable comment, to encourage my efforts
Best explanation sir.... Today only i know, purpose of zero current detection... Thank you very much sir... God always prosperity in your life...
You are most welcome
it is my pleasure that my efforts are useful
Good evening brother. Though I don't understand the technical things, but always like your presentation and way of explaining
Thank you very much dear sister
it is your greatness
very well explained, bravo sir🏅🏅🏅you made technical books easy to understand and interpret
best regards and special thanks for your valuable comment
I also recommend to use a transistor tester before you install the part so you can check the capacitance and vge. This goes also if you have a bunch of transistors you need to change, test them all and select the ones that are close in value. With all these chinese parts now sometimes there are defective parts or out of spec. Always test before install.
Pls my igbt keep burning out even when I put higher number
ma shaa Allah
fabulous informative discussion on igbt failures. your analysis is always effective in electronics work. stay blessed dear brother
Many many thanks dear sister
@@HaseebElectronics thank you, Mr. Haseeb, you are a very respected and good person, You explain schemes and theories very well and nicely, I often watch your recommendations on your channel.
Super explanation, thank you very much, iam from India, Hyderabad, thank you 🙏💕, do more such videos
thanks a lot dear
you are most welcome
When I saw this, I think first at the fake component avalaible on ebay and aliexpress. They are sometimes rebranded, and gate capacitance is not the same, and bandwitdh is different. THis is the reason why it works few hours, and failed when overheating.
If the capacitor of the LC circuit is dead, you will maybe just have a lack of effeciency. Thanks for the video, god bless you.
Amazingly useful information
Big Like from London 🇬🇧💌
big thanks and special thanks
You are a very clever man, thank you for your videos
Lk 149 brother 👏👏👏
keep it up
Thank you so much 👍
MashaAllah
Great Sharing 🌹🌹❤👍
excellent class very clearly explained
it is my pleasure
جزاك الله خير .
لقد تعلمت اشياء جديدة لم اكن اعرفها .
شكراً جزيلاً يا استاذ.
Salam brother you showing good work and telling god bless you by 🇺🇸🙋♀️
thanks a lot dear sister
Excellent teaching. Thank you, Haseeb.
You are most welcome
hello dear brother. i wish he would explain how to calculation the capacitor connected to the coil. yiu are unique in the world of electronics
Very useful fault finding method. Thanks
You're welcome
Greetings from Poland ! :)
best regards and special welcome
Very GOOD video, Sir. Sourcing components is HUGE issue. Too much falsely marked JUNK from non-authorized-distributors. Sometimes seems quicker or cheaper, but not really; and clients get mad when equipment down over and over. Now, in USA, i ONLY buy from Digikey and Mouser. Clients and me are happy to get OE performance out of repaired equipment.
thanks a lot and lovely thanks
you are absolutely right that component sourcing and falsely marked components are biggest headache and loss of money. and biggest issue the client's trust.
please accept my best regards
Masha Allah informative as always..
Many many thanks
clear explanation. if we are using polarized capacitor then it will not affect the capacitor changing the direction of charging current from inductor.
Fantastic video 😌 big like
Big thanks
Very informative like always. Shukriya Maestro.
So nice of you
@@HaseebElectronics Maestro can you make a video explaining the meaning of connection or how does the KCM15F60GA IC works thi Ic comes in Samsung washers motor inverters please
thanks very much sir for sharing...god bless.
You are very welcome
MashaAllah very useful info
Nice sharing👍
thanks a lot dear sister
Hi sir..,very interested and informative video.
Thank you very much. Have a good day 🙏
thanks a lot dear
Good tiching karte hai 👌👍👌👌👌👍👌👌👌
thanks a lot
Thanks for your support. However there are two thermistors in the circuit for over Temperature. So when the IGBT overheats then the Microcontroller is supposed to switch off, can you throw some light on this?
Thanks.
Big Like For Good Work
Big thanks dear brother
una pregunta el datasheet q tomas como referencia a que igbt (numeración ) pertenece. muy buena explicación
Hi thanks for the informative video and for the preventative ways to avoid components being destroyed
You are welcome!
it is my pleasure
stay blessed
Very helpful information, most appreciated
best regards and special thanks
ماشاءالله You are too Good sir
best regards and special thanks
You are amazing brother.🧡
Thank you so much 😀
Great 🌹
Thanks for the visit
very great sir.. thanks..
Most welcome
When choosing a replacement IGBT, don't forget to check whether or not the component you are replacing and your replacement component have an internal flyback diode! Most modern devices contain this, but not all. Always check your datasheets.
Don't assume that adding one where there was not one before is a good idea. Generally it is best to use the exact same part the manufacturer used whenever possible.
The video is informative, thanks for sharing.
best regards and special thanks
MashAllah bhai
thanks a lot bhai
Ma'Sha'Allah nice information sir
Helpful and informative video
thanks a lot
stay blessed
Realy u r genious
Really Informative Video ❤️
it is my pleasure
السلام عليكم و رحمة الله
جعل الله لك هذا العمل في ميزان حسناتك يوم القيامة.
Excellent explanation. I hope you do a design example with testing experiment of an induction heater. I am very interesting with induction heater, it is very tricky.
Very useful information sir thanks for sharing this knowledge to us
it is my pleasure
وعليكم السلام great people have always fantastic output
best regards and special thanks
ماشاءاللہ ماشاءاللہ بہت خوب*
I have Induction cooker . Replaced igbt pair already. But nearby ZD diode also shorted. The diode in other side of cooker reads as normal diode perhaps IN 4148. Do u think is standard N4148 is ok to replace?
good job
Walikum Salaam Bhai Sahib
shukriya bhai JI
Hi Haseeb. My capacitor is 800V 0,25micro farad. I measured 230 nano farad. Is that problem. Also I have 4 IGBT who works on two couples for each end of the coil. One of the couple give me a short circuit if I measuring on board. If desoldering them their value are normal. This their condition is same if there is no power on the motherboard. I had short circuit damage and one IGBT was burned. Also big diode between rectifier and IGBT. What is your opinion. I ordered other three IGBT to replace them too.
sir it is possible to double the igbt of an inverter welding so that it would not blown right away..?
Nicely explained, thank you so much
You are welcome
Beautiful information.
best regards and lovely thanks
Watching here
Wow informative video
Thanks a lot
Zabardas video
best regards and special thanks
excellent
Many many thanks
49 lk dear💕💕💕 beautiful share Bhai aap nhi ate hi Bhai
الله يبارك فيك اخي العزيز
best regards and special thanks dear brother
Good work sir
best regards dear sister
stay blessed
Watching now thumbs ups done sir in your experience what brand of soldering lead do you recommend to used sir
there are many brands
Kestre Soldering Wire 60% Tin/40% Lead with Flux Core
Maiyum Solder Wire
Wyctin Solder Wire
Austor Solder Wire
Hgmzzq Solder Wire
Cardas
Mudder
alpha solder wire
Wyctin china
alphametals
Great sharing
Assalamualaikum.. Good video sir... Can you explain/tutorials how 7 digit led number working n ic it use.
aslaam brother, sukraan for the indepth teaching of Why IGBT keeps on popping, am working on a cooktek induction single hob, fuse keep on popping when I replace it and it has 4 inline IGBT 's, and I was thinking before I put in the new ones, reasoning to myself why and your video just made it clear the reason why it keeps on burning out because of the coil or maybe something els, can you give another explanation on it kanalah.
Sir we have a ador mig 600 welding it's igbt burn frequently, so I cheek this machine igbt input DC series with a indutor coil and a 1ph bridge + ,- only connection with coils it's damage it may be course of igbt burn ?
Dear Haseeb. My treadmill 's IGBT keeps burning within few seconds 😢. Could you please explain why?
Masha Allah great information
thanks a lot
Thank you sir,
best regards and special thanks
Very informative, thank you.
Could you please make video about zero cross sensing and such other sensing circuits in induction stove...
Great information thank you for sharing
Very welcome
Gotta hate when that happens . Lol
Thanks for video !
Very keenly explanation You try to explain, is very much helpful to me , but in our repairing table please teaching us the pin point tips for quick rectify the equipment ,kindly help me for the substitute for IGBT RJH 60F7, Which is currently not available in local stores, thanks for sharing the great technical teaching,
FGA6065ADF
IXGQ50N60
TIG110GMH
Thanks Sir for Your quick response 👍, Stay blessed
can u please upload vedio on 220 vdc battery charger scr control ckt
Bai me welding machine me igbt lagata hoon to forn patakha marti he jab k transformer ki jaga output me bulb lagao to thek operat hoti he bilkul thek on of hoti he through dri circuit .lekin jese hi output transformer wali wire conect kre to on krte hi jal jati he.kia transformer to kharab ni jab k transformer k bad rectifier diod module b thek he.plz help n ap igbt se age output tak video bnae.
Brother i have an induction model-prestige 16.0 ,
in the drive section 8050 pnp transistor was open circuit i replace it and induction worked for several days and after that again the igbt went short circuited 😢😢😥 plz help me
Nice
اللهم صل على سيدنا محمد
valekum salam elder brother how are you
thanks a lot dear brother
Jazikela for sporting 🙏😭
best regards and special thanks
MasaAllah. Jajakallah.
thanks a lot dear
Ma sha allah
thanks a lot
stay blessed
MASHALLA 🌹
Jazaak Allah khair
snubber circuits need replacing
in resonant circuit, most of time there is not snubber circuit. because in induction cooker the resonant technique is used
snubber is in fluback topology
I have this problem on a barand new Induction cooker for the last 6 months still NOT rectified. I wish to contact you on WA or email
if possible. Thanks.
I have the same problem.
Sir make this video in urdo.
کل ان شاءاللہ حسیب الیکٹرونکس اردو چینل ہر ملے گی
جميل watsapp
thanks a lot
Bosss short vedio bnaen
i will try my best, but it is impossible to explain clearly in short videos
but i will try my best
please accept my best regards
@@HaseebElectronics my concern is that reason for igbt blown out is same as fuse example current rating or voltage
@@ehsanuddin7706 the biggest headache is fake marking numbers
may that is not that igbt but it it named by fake marking
sometimes quality failed components are supplied
always try to purchase from some reliable source
Sir hindi ma batyie plz
Vge parameter