I built one. I made my stock 1 in thk with Parnell 20deg. Cuts on side. Large rectangle on bottom I made 14 in Long on top side. End angles are 20 deg as well. Made 14,12,10,8,6,4. Rectangles. 2 of each. Top I cut at 20 deg to make the point.
*Here is My Twist on Your Build!!! How did I Do?!?* *Making Wood Christmas Trees | 3D Geometric Christmas Tree | Step up Your Wood Working Game!!!* th-cam.com/video/P50MRnzeGcY/w-d-xo.html
Very Nice! I just built this myself, and here's what I was able to figure out between the video, other comments below and my actual build (U.S. / Imperial units and lumber dims): Used 1x2 for everything except vertical base (1x6) and top cone (2x2). Ripped 20deg sides on 1x2's with table saw, removing as little material as possible. bottom of tree is 16-3/4" wide (16" pieces) followed by two each 14", 12", 10", 8", 6", 4", 3" and than top cone - came out a bit wider and shorter than this video, but the 70deg sides line up near perfectly to the top. Hardest cuts are ends of 1x2's, need a compound miter saw set at 20deg on the base and 7.5deg on the bevel. Flip 1x2's after each cut (watch video closely) and lumber direction matters - you'll have to experiment. Again, very cool and thanks to I wooden for posting this!
love what you made here, maybe to stop wood falling to ground have a chair or hobby hors to rest the end of wood once almost through the saw that way you not have to bend yourself or damage the wood x keep on making x Vanessa
it is a beautiful x-tree , it wokld be nice if he posted at least the angle of cutting ,and the high of the this trees .. nonetheless if we draw a x-tree on a big piece of cardboard the we want it ...from them we can get get the angle .....
The angle that was shown is the only one used throughout the whole build for the top. 20° 4-2x4s were used. That completes the top. As far as the Stand, that is something you could make with your own design.
Thanks @bradyoung7292 I tried 7.5 ° on the bevel and 20° on the base I flipped each piece over however I always ended up with the inside joints having a gap and the outside joints the ends were proud off the sides. Is it possible that I started my first cut with the wrong edge against the fence? I had the 20° cut on the base so the top edge was tight against the fence. Wish I could figure it out. Any suggestions? Thanks.
Está muy bien pero... Antes de montarlo yo le doy una pasada de gasóleo a TODAS las piezas y lo dejo que se empape bien , después lo dejo secar y se barniza , en lugar de grapar se marca y se atornilla para poder desmontar
From what I could see, the "table saw" aspect we well as the bevel, were on 20 degrees each. As far as the measurements, it seems that you could make it as big or small as you would like.
I would sure like to be able to get the measurements for this tree!
I built one. I made my stock 1 in thk with Parnell 20deg. Cuts on side. Large rectangle on bottom I made 14 in Long on top side. End angles are 20 deg as well. Made 14,12,10,8,6,4. Rectangles. 2 of each. Top I cut at 20 deg to make the point.
Hardshell Woodworks does.
*Here is My Twist on Your Build!!! How did I Do?!?*
*Making Wood Christmas Trees | 3D Geometric Christmas Tree | Step up Your Wood Working Game!!!*
th-cam.com/video/P50MRnzeGcY/w-d-xo.html
oh It's was great 👍
@@iwooden2507
Thank You!!!
Merry christmas and happy new year!🎆
@@iwooden2507
Merry Christmas!!! Thank you for the Inspiration!!!
Very Nice! I just built this myself, and here's what I was able to figure out between the video, other comments below and my actual build (U.S. / Imperial units and lumber dims):
Used 1x2 for everything except vertical base (1x6) and top cone (2x2). Ripped 20deg sides on 1x2's with table saw, removing as little material as possible. bottom of tree is 16-3/4" wide (16" pieces) followed by two each 14", 12", 10", 8", 6", 4", 3" and than top cone - came out a bit wider and shorter than this video, but the 70deg sides line up near perfectly to the top. Hardest cuts are ends of 1x2's, need a compound miter saw set at 20deg on the base and 7.5deg on the bevel. Flip 1x2's after each cut (watch video closely) and lumber direction matters - you'll have to experiment. Again, very cool and thanks to I wooden for posting this!
good luck my friend
Cool project, thanks for sharing
Thank for watching
Very beautiful!
Excelente trabajo, felicitaciones!!
Thank for watching
Bravo et MAGNIFIQUE 👍👌
Beautiful Work!!
And I like your 3 combo saw!!
Oh it's very good. 👍
Outstanding!
love what you made here, maybe to stop wood falling to ground have a chair or hobby hors to rest the end of wood once almost through the saw that way you not have to bend yourself or damage the wood x keep on making x Vanessa
Thank for comment!
Excelente trabalho ficou muito legal que Deus continue abençoando você e toda sua família amém 👪 👪 👪 👪
Thank you so much
Fantastic, I love it
Thank you so much
Well done … it’s beautiful !!
Thank my friend
it is a beautiful x-tree , it wokld be nice if he posted at least the angle of cutting ,and the high of the this trees .. nonetheless if we draw a x-tree on a big piece of cardboard the we want it ...from them we can get get the angle .....
The angle that was shown is the only one used throughout the whole build for the top. 20° 4-2x4s were used. That completes the top. As far as the Stand, that is something you could make with your own design.
Hardshell woodworking. Has full build and instructions on how too.
Very nice build. Very original.
Thank for watching
Arrasou !
Lindo demais !
Parabéns !
Outstanding. Very innovative. Thank you.
thank you so much
God bless you
I would like to get plans for this build ❤
Nice ❤❤❤
Well done son merry Christmas nice video from Wales UK 😊
Thank you so much 😊
Great job it's beautiful you did a wonderful job
thank you so much 😊
Very nice! I will be building a couple of these soon. Thanks for the video.
thank for watching
Good luck my friend
This is awesome and has potential for so much more. Thank you for a wonderful video and the inspiration! You did good work my friend!
Thank for comment
Sehr schön geworden 👍👍👍👍
Отлично!!! А у нас ёлки живые растут!!! Много!!!
Very nice!
Beautiful
thank for watching
super!
Amazing 🫡
It would be great to know what the measurements are when cutting the pieces on the miter saw. And how many of each to cut.
Belíssimo trabalho parabéns
thank for watching
2:10 Fly something from your table saw.
Is your mitre blade tipped? At what angle? Love the build.
Nice work! What finish are you applying at the end?
Que coisa mais linda, parabens
Thank you so much 😊
Top muito top, vou fazer
Could you make me one?
Thanks @bradyoung7292 I tried 7.5 ° on the bevel and 20° on the base I flipped each piece over however I always ended up with the inside joints having a gap and the outside joints the ends were proud off the sides. Is it possible that I started my first cut with the wrong edge against the fence? I had the 20° cut on the base so the top edge was tight against the fence. Wish I could figure it out. Any suggestions?
Thanks.
Wow🔰
This is beautiful and i would love to build it! Where can i get the plans?
klasse - Litauen
Excelente proyecto podríamos saber las medidas de las piezas bendiciones
I'll buy a set of plans if you can make them up
Está muy bien pero...
Antes de montarlo yo le doy una pasada de gasóleo a TODAS las piezas y lo dejo que se empape bien , después lo dejo secar y se barniza , en lugar de grapar se marca y se atornilla para poder desmontar
Thank for comment
Que medida tiene la primera basa? Gracias
45cm
what are the measurements
I really want to make this can you tell me the measurements
what is the measurements you made the tree with ?
Was anyone able to figure out the dimensions? It's really nice I would like to make one
Check the reply to the first comment.👍
Could I get the measurements, and the angles for this project?
From what I could see, the "table saw" aspect we well as the bevel, were on 20 degrees each. As far as the measurements, it seems that you could make it as big or small as you would like.
👍👍👍👍👍👍👏👏👏👏👏👏👏👏👏👏👏👏👍👍👍👍👍👍
Measurements for this project and angle cuts ?
A little commentary would be nice, for those of us who aren't mind readers.
Wonderful. Do you have a cut list for this?
44,42,40,38,36,....,4
it also depends on the height of the wooden bar. I used 4 cm wood
Thank you. Merry Christmas!
I’m assuming your dimensions are cm.
Do you have patterns for this tree for sale?
Are there patterns for this design?
Has anyone figured out the measurements?
❤m
👏🏻👏🏻👏🏻👍👍👍
Cuáles son los ángulos que se utilizan
I use a 70 degree angle
I guess it shows you how he built one, but he won’t tell you how to do it
🤔👍💪🇦🇷🇦🇷🇦🇷
👏🏻👏🏻👏🏻❤️
watch my next videos please
but you don't tell us how to make it no good
Why is he wearing a mask? Is he sick?
How is that question relevant to the video? Are you being a COVID troll and unhealthy in the maturity department?
Its an honest question.
Dust. From the saw and sanding.
Want sawdust in your lungs?