วีดีโอ

Thank you for this video …very easy to understand

hy 18V battery, 24V controller, 12V-motor 18V 4ah, how long can you last? What is max RPM recommed? Possible with Ford ranger 4x4? how could the operating time be increased? They go straight a lot

I bought new 12v batteries for my kids car. We already used it but when the battery went low i charged it but it coudnt pass 11.9 v mark using the built in charger.b What might be the problem from the car?

Thank you very much for this video!

Awesome video thanks

Hi any help I can get with steering not working on my sons car? Reverse and forward work with remote on pedal. Steering is super hard by hand and does not work on remote as well. I have a 380 12v motor with gearing on the way. Hope I made the right decision?

Very helpful thank you!

Mine wont charge, when i connect the charger it blinks red and green any idea what the problem is?

Thanks for the video it helped a lot great job 👏🏽 👍🏽

What a seriously stupid amount of work to change battery

My daughter has G500 12v, everything works perfect, manual accelerator works perfect too. And The parental remote connect to the car but it won’t do anything else. I got a new remote but it does the same. Pairs to the car but doesn’t function.

12V DC motor , Ford Ranger 4x4 possible work 20V battery?

Hi, so my son pulled a wire, and i don't know where it should connect. I press power on button and it turns on, as soon as i let go of button, it turns off. Truck moves and does everything normal while i hold power on on button. Any suggestions?

Thanks!!!

Thank you

Upgraded my sons 12v to 18v Milwaukee power and it worked perfect for the first day but now won’t move. When the switch is turned on the battery level indicator on the dash still reads full. Did I burn out the control board?

Thank you for sharing the troubleshooting steps. I checked my power out of the controller and it is 12.2V without pressing the pedal. Is that an indication of a controller gone bad? I originally thought motors were bad and replaced them but still not powering the motors. I checked voltage at the the motor connect and it read .1V. Could the cable be fried?

Do you have the video of this set up where you have the speed controller with the voltage regulator?

Thnx

Thank you so much ! I did it in less than 1h Thanks for all the details !

Dope vid, what was the rating on the Resistor for brake?

One question please, I have bought a car for my son and I changed the motors, I put in higher revs. my problem is that it works for 15 seconds and then it turns off by itself and turns on after 5 seconds. this happens constantly. it had a 12v battery 4.5Ah and I put a new 12v 9Ah one but it still does the same thing. Do you know what the problem is? Can you help me?

Thanks for the video. I've got a couple of observations. #1 If you're using your jumper cable battery kit to preserve the memory, you don't need to buy the memory saver kit. Just attach the jumper cable kit to the battery cables under the hood. Same result. #2 and this is, potentially, a big one, I don't think you have to remove all the parts forward of the battery wall and slide the battery out. If you just remove the pieces around and above the battery, the battery WILL lift out. However, you'll have to disassemble some of the wires connected to the battery cables to get them out of the way. I saw this done on another video here (unfortunately after I'd changed my battery out). An extra minute or two spent on the battery cables is a lot easier than pulling out all those other parts.

Thank you for the information sir 🙏🏻🙏🏻 because I plan to use this LAC board for a remote-controlled my lawn mower.

hello! my son got ahold of a cool remote control jeep.. but we have found that the steering is not working.. we took it apart checked it out but i couldn't test anything.. i dont have a dvom here.. im unsure where to go at this point any suggestions? its a "brothers" jeep

Great video. Thanks for posting. Would you happen to know why the new battery won’t register? I’m using ZURICH ZR-BT1 Bluetooth code reader. Battery was upgraded from flooded to agm.

Hey! I have a 24v jeep and the connector from battery to motor melted and is not powering on. Should I just replace the battery?

I love Animals

Have 24v atv that change controller board because wasn’t moving now it only pulls slow. But if raise up back tires spin fast and freely

How can I keep the tires from slipping in the grass??? I sprayed flex seal on them and they still slip???

Where’s the link for the video for the h11 premium trim replacement

Hello, My name is Mike and my daughter's new "Ride on car" doesn't turn right with the rc, you can turn to the right manually but not with the rc. She's too young to turn it manually and was hoping to figure this out to repair. It looks like the wires are hot glue gunned in and and I'm wondering if maybe it's just a loose wire? Hopefully you can help, thanks!

Thanks !!!

Hi, thanks for the helpful video. I hooked up a 20 volt drill battery, worked great for about 10 min. Now it won’t turn on, so ordered the control panel/ receiver. Could it also maybe be the on off control panel JR1927M-12V? If I did want to continue using the 20 v drill battery would you recommend using the 24V on off control panel with the 24V control panel/ receiver? Thanks

What will happen if I skip the registration process?

very helpful, thanks a lot .

I have a ride on car that I bought yesterday for my 3 year old. He took it outside and a neighbor’s 10 year old rod on it w him for a good 10 mins. Now it sounds like crap. Lots of squeaky noises. How can I fix that?

excellent tutorial! only difference for me on a 2017 mini cooper s convertible was no vent hose

Great instructions! My 2017 Outback 3.6 limited HID factory bulbs were these exact bulbs that you show in this video.

👍🇲🇦

Hey bud! Your videos are awesome! What’s the best way to Reach u? I have a few questions to ask!

I follow along until the last minute of the video in regards to replacing the white power wire with your own. Where does the new wire connect to? I assume to the fuse ? Please elaborate

I upgraded my daughters jeep from 12v to 24v, motors and control board. The wife wants a speed controller added as full on is to fast in her opinion lol. I know the supplied pedal is either full on or full off (soft brake is planned) if i replaced the pedal with the variable pedal would i still get full on and full off? Would the ESC basically replace the control board if that is the only way to have variable speed?

Is there a specific position the motor should be in? Like can i do this while the motor is laying flat in the bucket floor or does it need to be in a vertical position (hung upside down)? Also for lubrication can i use penetrating oil? Thanks a lot

I had to buy the snake, but it was worth it. My washer is draining again.

can you reach out to me please i'm pretty sure the issue with my sons mack truck is the white long part on the switch board the accessory part but could use a second option. i've been able to fix it so far but i think its in the wiring. please reach out to me if you can

Busted the plastic tabs that the metal clips latch on to, any body know if there is an easy fix?

Hi with a full battery what should the voltage reading be? As you had shown 12 on your led display.

Does these conversions only work for 12v vehicles? What about a 24v unit. How to make that work?

How would you test the motor