- 9
- 168 444
Yoys
เข้าร่วมเมื่อ 16 มิ.ย. 2018
DIY Sprinter Brake Light Fix in 10 Easy Steps!
#DIY #VanLife #Sprinter
A quick tutorial on how to replace a burnt bulb on a 2009 Dodge Sprinter using just one screwdriver and a new bulb. The same steps apply to all Sprinter vans whether they are Mercedes or Dodge branded.
A quick tutorial on how to replace a burnt bulb on a 2009 Dodge Sprinter using just one screwdriver and a new bulb. The same steps apply to all Sprinter vans whether they are Mercedes or Dodge branded.
มุมมอง: 269
วีดีโอ
DIY How To Replace Low-Beam Xenon Headlight on Audi B8 (IN 10 EASY STEPS!)
มุมมอง 91K3 ปีที่แล้ว
A quick tutorial on how to replace your low beam xenon headlight on an Audi B8 (A4 2009-2012). If you found this video helpful, Subscribe! #DIY #Audi #Repair
DIY How to Replace a 30 Amp RV / Boat Plug
มุมมอง 3053 ปีที่แล้ว
Step by step tutorial on how to replace a 30 Amp plug on an RV or a boat. #DIY #RV #Plug
How to Fix a Flat Tire anywhere in 10 Easy Steps!
มุมมอง 2804 ปีที่แล้ว
In this video we go through 10 easy steps on how to fix a flat tire while on the go! Warning: Lifting your vehicle on a jack can be dangerous if the ground is uneven, or if the vehicle is pushed while lifted (when loosening and tightening the lugnuts, the vehicle must be lowered to the ground) You will need: [Tools likely included in your vehicle] Jack Lug Wrench [Tools needed that may not be i...
DIY Audi A4 2012 B8 (2008-2016) Oxygen Sensor Repair (IN 10 EASY STEPS)
มุมมอง 72K4 ปีที่แล้ว
In this video we go through the steps of replacing the bank 2 (post-catalytic converter / downstream / rear) Oxygen Sensor on a 2012 Audi A4 (applies to entire B8 generation, 2008-2016 models). If you are getting a "P0430 - Catalyst System Efficiency Below Threshold (Bank 2)" warning from your OBD scan, this could solve your issue and get rid of the engine light. This is the more difficult sens...
what is part number for this?
I heard the 2019 going forward models improve so much in reliability. I’m getting a 2019 premium plus as the grocery getter and road trip car. I hope it last five years.
No
Wowsers I’m pretty sure you ripped the wires when pulling the plug out, cut some hoses to get the wire through then put that dirty glove on the sensor but what would I know
is the display touch screen?
buena, que guantes se usaron para el video?
Hi. Sorry, but why you change them? I have the same car and excessive fuel consumption. How can I know if it is this sensor?
shows the most zoomed in video in the world doesn't really show where it located
because he changed the bank 1 and not 2 like the caption says. :( This video is very confusing.
Very helpful and straightforward! Thanks! 👍
Never sell it. I miss ours, although it was shit.
Good philips ❤
Cheers this video has give me the balls to try it myself 👌
?Would you be able to provide the p/n
Io ho una audi b7 cabrio del 2006 dove trovo lo spinotto lato guida o passeggero grazie
I’m getting a p2196 code, sensor 1 signal stuck rich. Could this be a bad o2 sensor?
I’m getting an intake air temperature sensor code. Where is it located?
Hi, With my OBD2 I get P0042 Should I change de O2 sensor (the one after the catalytic?
I'm having the same problem. What solution did you find?
P042000 and P044100
It says Bosch on the packaging. Do they make the O2 sensors used in Audi vehicles?
Hi, could you please provide the o2 sensor part number used in the video. I can only see my plug part number on mine. Thank you!
That’s the easy side to fix
That is upstream O2, downstream is about 12 inches before. Your description is wrong, but good video
I have a 2013 A5 and your video is the only one that have seen that shows removing the low beam bulb when there is no retainer clip to rotate. Just twist the bulb to the left to remove, then to the right to reinstall the new bulb. I have the exact same original bulb. It does seem that every bulb replacement video shows variations in removing the light housing, even for year and model the same as mine. Also, determining the best replacement bulb has been a challenge. I see you replaced the Philips XenStart 9285 335 244 (D3S 35W) with the HID XENON 9285 161 296 (D3 35W/55W) bulb.
I wonder could be the cause of my misfire?
Unlikely but maybe. Misfires most commonly happen as a result of a bad spark plug or bad fuel. Id check those first so you don’t spend too much for an o2 sensor and find out it wasn’t the issue
@@yoys1333 you're correct
The bag opening was a real eye opener
😅
Do you have to reset ecu after replacing the o2 sensors?
You could clear the error codes on the ecu after it’s been replaced and if the engine light doesn’t come back on, your problem’s solved 👍
I've looked at a lot of videos about removing the housing and your was the best. HOWEVER the best tip you gave was the Trox 30 in with the spare wheel. You saved me buying one. Thank you. Liked and subbed.
th-cam.com/video/1ZUOISEQK98/w-d-xo.html
i love the changing colours!!! such a satisfying video!!
Thank you! I know right, I love it too!! 😍
There’s is a cable up on top right above the vaccum pump it’s a connector I don’t know what it’s called please email me at zombiemode18747@icloud.com need help
What size is the key in his head by how much?
Low beam? Do you mean the drl strip?
Nono, there’s the daytime running strip, the xenon low beam for regular night headlights (which is what I’m changing) and then the high beams for when it’s really dark out!
Pure epicness
perfect space heater for your RV ! looks great
Thanks!! It warms up the rv space really well!
what a beast
💪💪
all of that with one hand! wow gj
Samantha Viloria Haha thank you! I could use a tripod next time for more stability
great video!!!! needed this so much!!
maymoona Happy to help! :)
Beautiful
SamanTIRED Thank you!!
Do you have a link on where I can purchase the right sensor for B8 2.0t
I would recommend your nearest Audi dealership
My sensor is extremely tight I broke a sweat trying to get mine off lol is there an easier way to loosen up my bank 1 sensor? I'm literally stuck at this point
Some extra leverage using a breaker bar could help
Hi all, I got a P2188 code but scanner says it state is temporary, so what could it be. A faulty PCV, injector leak? Any help will be appreciated!! Thanks in advance.
Got that code too ! Hopefully he gets back to us
It could be your mass airflow sensor, you can either replace it or try giving it a cleaning and resetting the fault codes after
Great advise! I cleaned it with CRC spray but code remains. Finally after also changing both oxygen sensors, spark plugs and its coils I found out it was the HPFP. I just replaced the O-ring and give it some maintenance. Best!!
@@hennzer hey what does HPFP mean
why not use anti-seize when putting on the new sensor? i hear that sensor will often get corroded on and then require a cutting torch to remove.
Underneath that cover that I removed, there is grease on the thread already
I have the P0420 code coming up, do I need to replace both oxygen sensors?
It's most likely the upstream or front (Bank 1) sensor, but you could replace both if you'd like to. It'll just be a little more expensive. Or you could try replacing one at a time and then clear the codes. Then if the code doesn't come back you should be good! :)
Could it be the cat? Replaced the upstream and nothing. Got cataclean but don’t know if it’ll help
That’s unfortunate to hear :( let me know if cataclean fixes it. If it’s the catalytic converter it’ll be an expensive fix. What’s your odometer at btw? And do you have oil or coolant leaks? (Do you have to refill them regularly? It would usually give you a warning when either the coolant or oil is getting low)
Yoys no leaking and it’s at 84k it’s running good and it’s up on oil. Little bit of an exhaust smell lately so idk what’s up with it. I’ll be putting in the cataclean soon within the next day or two
@LaynezWrld That’s quite unusual for 84k and no leaks. Maybe it was something in a recent gas fill up or the cats gone really early. Sounds good I’m hoping the catclean helps
Hi friend, I’m frustrated with my B8 I keep getting that the upstream sensor malfunction problem with solenoid adjuster 4. I just changed both of them and also made sure electrical connections were okay. Would you happen to know if the downstream sensor you changed could resolve most issues? I know that if one thing is bad it lights up other things that could be okay. Thank you
Hi there friend! What's the error code you're getting? I replaced both oxygen sensors and then reset the error codes in the OBD scanner to get rid of the engine light. The error codes stay in the computer's memory until you reset it through the OBD scanner. You can try resetting the error codes and see if your error comes back. If it comes back after using the car again that means the issue lies in another part. Hope that helps! :)
I definitely appreciate this tutorial Yoys! I was trying to find out if upstream/downstream are the same and if they can be DIY repaired.
Glad to know it helped Chris!