วีดีโอ

Are they available on your website?

I got the galvo version and it will not hold a tumbler even with a double wheel at the other end locked in and square. I tightened and it still wobbles. 40 oz tumbler. Tried all feet.

Looks like 💩

Darn! I should have waited a few more months to upgrade my rotoboss to the ascend :(

Can you do a video of the RotoBoss Talon engraving a pattern 360 degrees around the top outer edge of the largest diameter wood bowl possible? Maybe a salad bowl or candy dish. The pattern could be a simple Celtic weave maybe 1/2” wide where the start and end meet perfectly aligned at top dead center.

No matter what I do, I can’t get #4 to stop them from falling out when fully extended

I thought I read this recently but am I able to purchase the chuck for my current roto boss?

I need one for a Aeon Mira 7

You have great Lightburn info. My suggestion is to work on your audio. Very difficult to hear. Appreciate your time.

Cool setup! How often do you have to take down that big ole' fan to clean all the gunk off the blades??

is this compatible with thunder bolt?

Saving me a lot of headaches. Thank you sir!

§£€¥

Great video thank you!! I received my first laser Nova 51 130W and I would like to know cat I connect exhaust fan to my gas heating exhaust ducting with T connector? Thank you!

I’m convinced

I want this so bad but I’m so afraid I won’t be able to figure it out. 😂

That is a nice video of engraving a 90 degree wall on a dog bowl. If it was a typical cereal bowl that had a smooth curvature and the side was tapered from the top down towards the bowl base, would the engraving be true or distorted as the laser beam travels further towards the bowl’s mid height and lower? Would it depend on the laser’s program… Creative Space, Lightburn, CorelDRAW, Inkscape… etc? I know xTool’s Creative Space program will plot and adjust for most convex or concave surfaces to be engraved.

What is the widest wood bowl (O.D.) that can be engraved with the Talon 4 jaw rotary chuck on the Thunder Bolt with the Z Table dropped as far as it will go? I want to engrave the circumference on bowls I’ve made on my wood lathe between 6” and 8” wide on the outside dimension.

howdoes this hold up with say a 40oz cup that has a larger taper mid section compared to a 20oz cup?

Just wrong! Going to have to change my pants now!

😋 'Promosm'

omg,interesting trip, ;))

How much weight will this hold?

Does using this kit in a Thunder Bolt replace the need for a drop-down tray like the Roko Twister tray?

WHOO first! Love the ascend I got at LBX thank you again for all your help with that

Have yall have any issues with the thunderbolt in the trailer while driving? As in alignment issues or anything at all?

Do you know if this works on a tumbler with a step down or is it just for a smooth tapered cup like the icon shown in lightburn?

Do you always do 2 passes with the Odin? Is this because it leaves lines otherwise?

Very impressed. Well thought out!

Promo SM 👀

Great info. I would have never thought of this.

Could you use this feature for a full wrap, or just for logos?

Should the rotary setup parameters, object diameter, be adjusted to the measurement of where the object will be engraving?

When you put the measurement in the warp tool, do you put the measurements of the actual tumbler for the top and bottom or the logo?

I am gonna order one Jason, looks nice

Great show gentlemen I'm here for it lets goooo! 💯💯💯💯💯💯💯💯

Did y’all partner with PiBurn Labs by Lendigital for your new product and color scheme?

Awesome!! Great video and well explained. Can't wait to receive mine.

That collet lock is brilliant!

With the knife blade drop down on the Ascend, can you raise the chuck all the way up on the Nova 24? For the larger glass beer mugs with handles.

Soo pumped to get ours!!

Great video!

Days away from purchasing a 24. Would you recommend one over the over (Rotoboss/Rotoboss Jr)..or one of the other rotaries on your website? Will be doing mostly 30oz tumblers...maybe some 40 oz Stanleys. Thanks for your help!

Can’t wait for mine to come!

If I get a 4 pin version, will it be compatible with any laser that uses a 4-pin plug for the rotary regardless if its a CO2 or Fiber Laser?

Where is the legend saying? what did he say???

Truly the best Jason. Keep up the great work. My RB is unstoppable.

What kind of tolerances can the laser plus rotary hold?

Please Reach out to support@rotaryattachments.com

what do you have fir makeup air for the shop? Its always sucking air in without possitive pressure. Also i think some clean outs at the bottom of each feed would make life easier to service.