วีดีโอ

Re-install and clear all codes,no adaptation or calibration needed

Thank you!👍🏻

@erkanselvi4930 your welcome! Be gentle while removing the cameras so windshield don't get damaged

I will try my best, thank you very much👍🏻

You're welcome!

If the wiring harness has never been updated or repaired, i would recommend looking into that

@German-garage After waiting for a long time after the vehicle stops working, for example, it starts after waiting for 8-10 hours in a stopped state. Could the crankshaft position sensor cause this? Could the l4 l5 sensor cause this?

@@German-garage spark plug, spark plug cables, ignition coils have just been changed, throttle butterflies are intact, the air flow meter has also just been changed, only the distributor pms brain and crankshaft sensor remain regarding the ignition.

Usually, if the crankshaft sensor is bad, the car will start after it has been cooled off

Have you tried to scan it or read obd Codes? It would tell you at least something to start with. Also, try to unplug both air mass flow sensors and try to start it. Did you test if you have fuel or spark? This will tell you where to look for the issue. If you don't have one of them, at least you know what direction to go

Seems like a bad amp, but try bypassing any other modules in the fiber optic loop, one at a time.

@@German-garage When plugging in a code reader it gives me code D157 "Fault in CAN Communication With Control Unit COU [ZBE]

@NicholasL2288 did you scan it with xentry? Or aftermarket scanner

@@German-garage I used my iCarsoft v3 made for Mercedes vehicles

@NicholasL2288 are you able to communicate with amp? Also, try to bypass some modules in the fiber optic loop

This video is for educational and training purposes.

You must have vediamo to activate engineering mode

Nothing will happen, but you might have a defective unit

Defective unit meaning the head unit or amp ?

@miLLkY32 do you have sound?

@ no sound. Navigation works fine Bluetooth connects but no sound

@miLLkY32 seems like bad amplifier

This video is for educational and training purposes, so it is easy for untrained mechanics to learn and understand.

Right!

@@Lagunastech touch pad similar to cellphone blackberry touch pad back in the days

@@skuperday right! 07-09 esp/abs module is different from 10-13 esp/abs module

You will need Vediamo software to unlock the unit, but you also have to obtain the anti-theft PIN based on the serial number of the unit you bought. Every radio with a lock will be locked if installed in a different car.

@ thank you, I have the pin. Going to find a shop that has the software to finally have the comand unit working…

@leventak911 Also, xentry can do it as well

I am not familiar with retrofitting,contact your local radio shops for more information

@German-garage Ich würde gerne einen 7 Zoll Bildschirm einbauen statt der 5,8 Zoll des originalen Mercedes ngt4.5

Non-professional tow guy 😁😁

Good to know

Dm instagram @german_garage

@mariuseu1990 If your car doesn't have AUX as a feature, then you can't activate it.

@@sergeymelnikov366 😄😄😄

My Maybach always goes to "Handover" when I follow these instructions???

Hello Robert! It works 100%,making you follow all the steps

@@German-garage My dashboard goes to "HANDOVER" not as your video shows. I can make it go to ASSIST but when clicked on it always goes to Handover??

@robertlikis3386 dm via Instagram @German_garage

cabriolethydraulics.com

I dont think that is possible

Ok Thanks

07s interior also looks good

@ nothing even close to yours brother, but I appreciate that

@@konstantinostselios1129 do you have any codes after unplugging the connector?

@ hi there no check engine light just a silent code stored even the dealership ignored no big deal they even know that it’s better to be unplugged

@konstantinostselios1129 Right! What year is your car? Have you replaced the chain tensioners?

@ it’s a 2015 E350 with 100 thousand miles with no issues I have never touched anything on the engine except spark plugs and coils it runs so smoothly you can’t even tell the engine is on i own Mercedes all my life I work on them I knew about that solenoid and when I bought it I disconnected

@konstantinostselios1129 nice! I have serviced a few m276 with over 250k having zero issues as far as timing chain. They run well if they are not neglected

@robertpadilla8377 you can still use vci, but some 01 models require 38pin cable, so I would recommend sdconnect for older models

Hello! There is no programming required but you have to clear all codes,if the issue still not fixed you might need new TCM

@@peternjatha6671 thanks. This is the original tablet

Yes, I've been using 5W40 in any 2013 model and newer.

Hello! Unfortunately, this is the best quality because the original video format cannot be changed.

If you can't set the clock,your unit needs to be updated or replace the unit

No idea

Unfortunately, this is an old video format, and the picture might be blurry

You can, but it is better to remove it

@@German-garage how come ? So I have a idea why ?

There are 2 ways working on mercedes cars. Professional or amateur,some people are amateur that will never be professional, and some are professional who will never be amateur. I am not sure what is your point that you are trying to make,I post videos to help people out and I hope this video helped you because if you knew how to work on mercedes you wouldn't be watching this video

@@German-garagewrong real mechanic knows short cut .. fake mechanic goes by the book to milk the clock .. learned that working on cars for 30 years

@slowazbmwkilla3073 This video is for training purposes,you can get the job done however you feel is the right way for you

Check transmission module for any fluid residue. Could also be solenoid or faulty valve body. What type of scanner are you using?

@@German-garage I thought that code refers to a "fault conductor plate"

@lawalemmanuel6027 it could be but i highly recommend scanning it with mercedes xentry DAS

You can but probably you need new anti-theft pin

Yes! If you have entertainment package (rear tv)

2006 has only hands-free bluetooth

Assalamualaikum brother, please can you share me the link where I buy vediamo.. thank you

@rilwanbalogun2930 check online,I dont have any link

Remote and headphones?

No the star diagnostic tool

I’m having this exact issue my headphones and remotes aren’t synced to my vehicle

@MillzMaybach you can purchase it from mercedes of Usa if you live in us, which will cost around 38k

Nice! How do you like it?