- 46
- 17 860
Austin Marr
เข้าร่วมเมื่อ 18 ส.ค. 2011
Dodge Grand Caravan R/T door and window not working
I show you very quickly how to fix your van to get the door to close and window to roll up or down. I decided to not use a butt-splice connector. I ended up soldering the wires, shrink wrap and 1/4” wire loom to finish it off.
มุมมอง: 12
วีดีโอ
Austin's Garage - Touring HD Tire Change: Part 1 - Tire Removal
มุมมอง 145 ปีที่แล้ว
In this video I show you how to remove the tire and wheel from a 2006 Electra Glide Ultra Classic.
1972 FJ40 e brake Output Shaft Seal Installation
มุมมอง 8K7 ปีที่แล้ว
1972 FJ40 e brake Output Shaft Seal Installation
1972 Toyota Land Cruiser FJ40 / Trans breather mod
มุมมอง 2027 ปีที่แล้ว
1972 Toyota Land Cruiser FJ40 / Trans breather mod
Base cost shooting - jambs 1993 Toyota pickup part 3
มุมมอง 109 ปีที่แล้ว
Base cost shooting - jambs 1993 Toyota pickup part 3
Clear coat shooting - 1993 Toyota pickup
มุมมอง 409 ปีที่แล้ว
Clear coat shooting - 1993 Toyota pickup
Epoxy sealer shooting - 1993 Toyota Pickup part 1
มุมมอง 239 ปีที่แล้ว
Epoxy sealer shooting - 1993 Toyota Pickup part 1
Clear coat shooting - jambs 1993 Toyota Pickup 3rd coat
มุมมอง 79 ปีที่แล้ว
Clear coat shooting - jambs 1993 Toyota Pickup 3rd coat
Clear coat shooting - jambs 1993 Toyota Pickup 1st coat
มุมมอง 159 ปีที่แล้ว
Clear coat shooting - jambs 1993 Toyota Pickup 1st coat
Base coat shooting - Jambs 1993 Toyota Pickup
มุมมอง 169 ปีที่แล้ว
Base coat shooting - Jambs 1993 Toyota Pickup
Base coat painting - 1993 Toyota pickup part 1
มุมมอง 569 ปีที่แล้ว
Base coat painting - 1993 Toyota pickup part 1
Base coat painting - 1993 Toyota pickup part 2
มุมมอง 619 ปีที่แล้ว
Base coat painting - 1993 Toyota pickup part 2
Is that the valves ticking? Mine does it to. Was gonna tackle it
What exhaust system you running ? It sounds great
Gas treatment will take that right out and 108 octane booster
😂
This happens to me because the rule screen in my carb was full of junk
The accelerator pump is bad easy fix mine did the same replaced the pump she runs fine now
Mine dose that too
Bogging is a sign of too much fuel and not enough spark. I use iridium spark plugs on my 06 TTR 250 and it makes a lot of difference from starting cold, throttle response and acceleration. Also reset your mixture screw, start with half a turn out from screwed all the way in
Leaning out on initial throttle snap can also cause bog. Lean bog is a big thing in small Honda bikes with non pumper slide carbs.
Thats cool i hafto do something like this to mine
Then how do you stop it from bogging because that's happening to mine when I go drive my dirt bike and hit the gas it starts bogging until I switch to the next gear and then it starts bogging again what am I doing wrong or what do I got to do to fix that
Carb
Thats normal if you turn the gas too fast
Do you recall what size bolts hold the backing plate on?
It’s Japanese so either 10mm or 12mm lol
Ohhh my bad - no I do not recall the bolt size. Call up a dealer and talk to the parts department, I’m sure they could help
i think this is normal. when the gas is suddenly opened, the accelerator pump releases a lot of fuel, so the engine stalls. on my tt250r raid the same effect. Evaluate the quality of the mixture by the color of the spark plug carbon.
Accel pump is supposed to prevent lean bog I would've thought
UPDATE: The former owner used "hondabond" a gasket maker compound around the diaphragm so the diaphragm was glued to the body and the accelerator pump nozzle orifice's were completely plugged.
You need to rejet and do the de-restriction stuff. It comes lean in stock form.
good job thanks
Let's fucking go!!!!!! Brad doesn't have his audio set to share.
Yes!!! First comment!!!!!!! Lmao
Urban_Operater LMAO 🤣🤣
Best vidoe yet
Yeah sure!
Very cool Stewy! U need a camera for Christmas!
Crazy filming bro!
I know......i need something better man the phone thing isn't really workin
Looking good Stewy!
Thanks MW! Its a bitch waiting on parts....
Good work Stew!
Good job Stew!
Lol I love it!