วีดีโอ

yeah and gas sedinent trap installed incorrectly

Thanks bro

They made the gas valve accessible

How did you jump itjerkoff

you can disassemble the solenoid too, they unscrew and usually clogged with calcium. Chip out the calcium, and soak it in white vinegar, it should work again (not the electrical part, just the actual valve

Not getting enough hot water, or is the water not getting hot enough for them?

ok

what should be setting on upper panel of humidifier? I have same one you have in video and my house is about 2700 square feet. its winter time in canada and could get very low temps! Thank you

Womp womp

How did you reset it

In Ontario if you break the gas line with this pipe range you will pay for it . Because they say that the range shouldn’t be bigger then 12 inches adjustable range

What about a water heater that's been sitting unused for years? Has that rotten egg smell. Drained it,turned it off and left the water running through it for 2 days and still stinks.

Great video! thanks for this valuable info!

🤦‍♂️

Great 🎉

Nice vdo

Informative vdo

Good 👍

This guy is a loser

The brand is RotoM Canada, but does the label or the box say anything about where it was made? I'm curious how the Canadian suppliers operate vs USA.

This is incorrect. You dont add the 35+5 and that makes ital a replacement for a 40+5. By putting the incorrect size run cap youre making the motors run inefficiently and will lead to early fsilure. Im sure he'll be happy to sell you a new unit then.

So how can you get that top floor to be more cool , install a separate unit or just the refrigerant is low. how is it low if the other floors are cool ??

Flush out the R22 and refill it with R438a (AKA MO99) R410a systems have their drawbacks, higher operating pressures and added internal complexity Test your compressor status with a Megohmeter, if its not reading well than you can replace the compressor if you're good at brazing

Brother, you can see exactly where it's leaking from. Armstrong furnace, very common leak point on the left side of the collector box, there's is an additional drain point for horizontal applications, the plug is often loose from factory. Just needed a little Teflon on the threads and it would have been fine.

So did ya replace or fix gas valve ??

Bro just top it off Jesus

Leak check fix leak and recharge . Save them some money new ac’s are terrible. If not properly installed

❤❤

super information

wow excellent experience

Nice video ❤

great job bro ❤

informative video 🎉

Leckinv ok leck find out rrparinv gasx relax ok systom off sltey snx gax out and cleinvpoint wdlding rrparing piprly afted testing nigtgeon and filllecking testinv 100psi chergrinvg testinv find reparing and con formed shower testinv miuom 20 ..30 mintetestinv gauegd marking find out no lecking ok gasnitgon gas rrmoveing ok ok vacuom mizing systom -30 come ok manigled guge 2side vacom and vslvd closed gued vacom pump off ok chargeing rrmovring sushion lind fixed cylandgas using gas r410 gas chergeinv purging snd cylder oppsit put ther chargeinv 120 to 130 systom chergunv ameper checkinv minom 130 sushion psi ok ruing testinv systom ok dis chef ..450 to 500 psi ok goo find no leck conformd remo vin clsein ovser reparinv old find out and systom cylader rmovring oversvering leck find solvrinv jobes

I hate that im on HVAC side of youtube now but since i am. Everyone should go see what type of refrigerant they have and order a cheap set of gauges. Then see what size capacitors your indoor fan and outdoor unit has and order one of each. So if it goes out you can swap it instead of waiting. I also recommend seeing what rating your contactor is and having one at your house. I mean just getting the capacitors and contactor will prolly keep your A/C running for years to come "But i dont wanta pay $30 for spare parts." Well go ahead and call a service tech and let them install one and see how much you pay😂 even if your not comfortable around stuff like this, just search it and 90% of the stuff you can find a video to walk you through. Then you can always call techs in if its too hard of a job. I just replaced our contactor few days ago. I can only imagine how much a service tech would have charged me. **before touching contactors look up a video and they will show how to discharge it so you dont get shocked "even with the power off"

You haven’t been doing hvac that long have you lmao

Dumb

Poped nice job bro I agree with you sometimes people are very stupid and need people like us 🎉

What do you do if the model or serial number is not visible anymore

You mean in your yute !! Youth lol

Gotta yell at it. Probably had a long night. Wake up !!!

My water heaters never had no fan on top

How embarrassing

How is it good 35 and 40 is 5 less. It's suppose to be 40 by 5

You are giving the nuts and bolts and going granual. Great vid! Thank you@

Think from the customers' pov. . So many contractors don't do that. I experienced that with a recent home reno. The contractor put in a new sink and cabinet with a space between wall and counter that was not there previously. Was not thinking about how items would fall in between. Good workmanship sees the future needs of the client and service people who will follow you. Nice work!

Awesome video by the way I have a big question for you I have a old hvac system call r22 I'm curious what type of HVAC system will you recommend that are affordable side we already have a 10 year furnace Rheem system they told me that I need to replace it but the Rheem furnace is working properly and fine during the winter months and hot days but the coolest system on top of the furnace is leaking underneath the furnace due to the cooler system drip pan is damaged and old wear and tear I would love to hear your opinion about this and your advice?? Honestly lm looking for a hvac system that can last more than 20 years at least 30 years like our old r22 did

People who don't have a water softener, but have a mixing valve really confuse me.

🙏🏻🙏🏻

Yes must be changed every 2-3 months