Awesome code, what are the accurate turns used. Especially the part where it goes back and turns left near the two red blocks, it’s hard to find the accurate angle. Thanks, hats off!
Hello, after looking at your machine, I feel like my life has suddenly brightened up. I really admire you. If possible, could you show me the drawings? Thank you very much
spin the intake forward or back forever before adding the drivetrain blocks. there should be a motion block not designating a motor group or motor to spin for a certain amt of times or revolutions. thats the block u need before the drivetrain motions. hope dis helpful :)
Can i get your email Eric I'm not sure if it was the right email that i sent it to and if it was the right email can you check you email just in case. Thank you for the videos and help.
How do you make your robot turn in an Arc while still driving forward or backwards. My team is also using C++ and this is something I couldn't figure out.
@@TheyCallMedasfsadfhjc I did that. I found out after trying C++. Though for some reason after my teams robot aligns with the goal zone, the elevator doesn't go up. It doesn't get stuck or anything but it just stays still.
basically, for an arc movement, you will need your drivetrain motors as separate motors like “left drive” and “right drive”. after that, u need to make a pair of the two for motion with “and dont wait” between the two. lastly, depending on the direction of arc desired, set that motor to a higher value than the other, making one side move more and making an arc of the robot. hope this helps :)
hey eric, i need some help with programming. i notice that your programs always look very smooth without many pauses between turns and driving. how do you achieve this? im dont know how to combine turning and driving into a single movement without pauses, and i dont know how to make it precise. can you help?
if you take the left purple instead of yellow, and push the yellow discs off while you are shooting in the middle, you will get at least 4 points more, right?
guys this is skibidi
Hello do you have any photos of your code or if you are using a PID then any photos of that please?
WORLD RECORD 🔥🔥🙄🦅🗣️🤑😱😱😱
How did you team do at worlds?
You know atticus
who is that😂
Who are you
aha？who am I？just a teacher from China😂
269A code
Awesome code, what are the accurate turns used. Especially the part where it goes back and turns left near the two red blocks, it’s hard to find the accurate angle. Thanks, hats off!
that robor loks familiar
defo not sus that all the robots with this auton look the exact same
How many points
Can you send a screenshot of your code pls.
The GOAT of autonomous is back!
Even that thing is working better than my brother 💀💀 TEACH ME 👹👹👹
can i get your code please
this from china
your auto are the best🎉
Odom or PID? Also what was score?
Bro bought his robot from china
he is the mentor
@@Ultra-nl7mvlol
Incredible robot design! Does your intake get jammed with purple cubes sometimes?
It probably never does
Probably not because that first roller moves up a lot
How does the robot not drift?
PID
Hello, how do you make the intake roller that quick to suck up the cubes
He has a wiggly roller
Hello, after looking at your machine, I feel like my life has suddenly brightened up. I really admire you. If possible, could you show me the drawings? Thank you very much
is intake ratio at 300 -150- 300 RPM top to bottom with connected pneumatic at 2" height front intake? That's really nice...
no pneumatics, its a 3:1 gear ratio
How do you code the bot so that your intake and drive-train, both work at the same time?
spin the intake forward or back forever before adding the drivetrain blocks. there should be a motion block not designating a motor group or motor to spin for a certain amt of times or revolutions. thats the block u need before the drivetrain motions. hope dis helpful :)
Can i get your email Eric I'm not sure if it was the right email that i sent it to and if it was the right email can you check you email just in case. Thank you for the videos and help.
maybe wrong email
Awesome awesome 🎉🎉, may I know where are you from and which team you belong to?
296a
is it me or does the robot just start by itself
hey look whos back! how many points?
Like 130
do you use any optical or distance sensor？
what kind algorithm you used to turn so precisely?
PID
Bro is on crack
How do you make your robot turn in an Arc while still driving forward or backwards. My team is also using C++ and this is something I couldn't figure out.
pd loop, search it up or use motor time out
I'm pretty sure you need to make two different blocks of code, one for turning and one more moving
@@TheyCallMedasfsadfhjc I did that. I found out after trying C++. Though for some reason after my teams robot aligns with the goal zone, the elevator doesn't go up. It doesn't get stuck or anything but it just stays still.
basically, for an arc movement, you will need your drivetrain motors as separate motors like “left drive” and “right drive”. after that, u need to make a pair of the two for motion with “and dont wait” between the two. lastly, depending on the direction of arc desired, set that motor to a higher value than the other, making one side move more and making an arc of the robot. hope this helps :)
can I add ur discord I need to ask some stuff
sorry i dont have that
is there a way i can contact you personally@@ericshen4033
maybe email，hahah@@thecappedpin
Hello Eric! What is your email? So I can communicate to you about this excellent design! @@ericshen4033
do you use text or block to code
text
C++ or python
C++
ill pay you 50 cents for the code (trust)
😁
INSANE
The goat is back
Wow!!! World No.1?
hey eric, i need some help with programming. i notice that your programs always look very smooth without many pauses between turns and driving. how do you achieve this? im dont know how to combine turning and driving into a single movement without pauses, and i dont know how to make it precise. can you help?
My english is not so good ,I think I dont know how to tell the detail to you
@@ericshen4033 you can use google translate
if you take the left purple instead of yellow, and push the yellow discs off while you are shooting in the middle, you will get at least 4 points more, right?
What sensors have you used?
Hi Eric my son is 12 years old , we are in California but we speaks Chinese too , may in add your wechat ?
Hi eric good job 👍
Can you give me a reference to the rap mounting mechanism ?
What software did you use?
You set the bar very high! I'd love to see that program, outstanding work!
太厉害了
谢谢，其实一般般😂
Can you show hand cam so we know its autonomous because your code knew exactly when to stop shooting. No hate just wondering
that is fixed times
Fix that scissor lift and holy moly you got an auton