วีดีโอ

what leveling feet are you using?

Lots of helpful tips and information. Great video! Thanks

It’s a journey, and you will enjoy it at the end when your looking back at how far you have come. The rebuilding/repairing process is a learning curve. But then it’s on to accessorizing your newly rebuilt mill and you find that the cost of that process is far more than that of the rebuilding process. Tooling is expensive but it is worth every penny. Keep pushing through one step at a time my friend, you are doing great ! Best of luck!

"Hoister"? There is definitely a "y" in (Hi-ster)🤦

👍🏻

That’s actually hilarious! Materials Needed: #1, A Lathe! 😂

That is fantastic! Great video. Thank you for posting this. Very helpful. Subscribed!

Nice. Thanks for sharing.

All it needs is a wedge under the one corner that will stop it from rocking. As for run out, you don't seem to be ready to work to tolerances closer than plus or minus .005. Spend more time making chips and less polishing the machine. My machines might be dirty, but i make chips almost every day. Practice makes perfect.

Why do you call it a Hoister

Good stuff! Bet it turns out great

Helpful video. I'm getting ready to build my shop and planning out where to put the lift. This was very helpful, thank you!

Good video. Better to have to shorten than to lengthen. BTW, I hope you're not putting all this effort into a coupe.

Awesome video dude. I was going to build a leveling system and I found this. Thank you.

Get a magnetic starter, your running blast cabinet and i bet that compressor was kicking on constantly. The points were probably burnt the F up. Its not hard to wire up. You will run your ground and 1 hot leg from motor to starter, then run your other hot leg to your curent switch biggity bam no more issues.

How about crank the motor and put a starter fluid in your

I have a small shop. When I was laying out my 2 post lift, I found my widest car and arranged it so that if the car was centered on the lift, I would have enough room to do whatever i wanted. The operation that came to mind was if I wanted to pull an axle. If the car is centered on the lift, the outside of my post arms are 27" wider than the wheels. It worked out such that the post is 4ft off the wall. The car is 6'3" off the wall. Tool chests are 18-24" wide. So if I happen to have a toolbox parked up against the wall, the car is still 4ft and some change away from that.

Perfect selection of equipment… super clean mill too👍👍👍

Excellent video. Very informative. Thanks for sharing your experience.

What model lift is that ? I have a Forward lift coming , I wish I had your space , I'm only 18ft wide and 24ft long

Great video, exactly what I was looking for. I want to install a two and a 4 post for storage and was looking for this information and visualization. Doing a 60x40 with the 40x40 section being a shop

i just retired after working for 50 years and in the middle of setting up a machine shop/welding and fab shop for something to piddle with. Same problem: if there is a level place on my floor I ain't found it yet lol. See last few months of my videos if you have a minute. Like your shop too.

Good stuff !

Is your lift asymmetric, appears so.

You really help me to figure out where to place the set back from the wall from the front to the post. I admire you're style in taking the time to explain this in detail, keep up your good work.

Instructions suck. Good looking out. Thanks

It's sad that current tech is built to last only till the day the warranty runs out.. my old man's air compressor is 50 years old now, runs up to 200psi, and it's only needed 1 motor change in the last 50 years. They definitely don't make them like they used to.

China, china..built.. bye American made..comprsoirs..champion, or Saylor-beall..or quincy...there built in this country..I own a Saylor-beall made in st.johns, Michigan.....I hope where u bought..will make it right. For you. Vary sad to see this. Today I installed a I.R. unit for a car wash ..5 h.p. 2 stage ..it looks ok..but no magnetic starter on it ..he bought at tractor supply.. big box store .. anything over a 5 hp. Unit should have one on it..pressure switchs can't handle the load..like your unit in this video..

Great video. You walked me through my install today. Thanks 👍🏻

Make sure you have clearance to pull an axle shaft out. Especially on a truck axle.

Good job explaining electrical. Wish me luck tomorrow. Same problem on my v- twin. Maybe a tri pod would help you with the videos. Frees up a hand.

I replaced my 1969 Rustang rear frame patch links left and right from CXJ Pony Parts which are well thought out parts but prior to welding I put a 5/8 x 4 long bolt and nut to lock it in place permanently.

Where to download 2J Head Repair Book

How'd you know that the drawbar shoulders should be 50 thousandths below the top of the mill?

THANK YOU! This helped a ton on installing the lock releases.

You have an excellent channel

Very detailed on installing the knee power feed. Do you have to support the knee when removing the shaft? Didn't know if the knee needs to be all the way down before pulling out the shaft to prevent the knee from falling.

cool gonns get one

i like the jig for holding drill straight :")

Thanks for making this video. I have a Nationwide 9k overhead lift (same design) and the directions are horrible!

Good video and that is a good brand of drive. Thanks

Should not need to buy any kits or plans if you own and use lathe s and milling machine if you need plans you better sale your equipment and find something else to do as to level machiney is a plus if there's coolant involved as there built to channel flows back to the tank

If you store your zero turn mower for the winter months, install a fuel shut off valve and run your mower until it shut down itself. You will clear all the fuel from the carburetor.

I`m impressed, not only with your weirdly back bending thumbs, but your ability to explain the otherwise confusing schematic reading. Thanks Jamel!!

Great video. You have saved me so much time by answering all of the questions that I had. Thank You. 😃

Tragic...a purchase this pricey is with buying an extended warranty.

If you don’t have a wiring diagram then you can use an electrical tester if you have one

Nice shop!! My mill sits on the pallet it came on from the shop I bought it from .. I think they had it in the same pallet for years … since there was tons of chips wedged into the pallet

Just excellent on presentation congratulations let there be more to show the back yarder