วีดีโอ

I have used model and I don't have manual can you please let me know if I need mix fuel or it will take direct gasoline

👍👍

Oh it definitely looks like a lot! If you fill that van to the ceiling you're gonna blow your axle!

I’m 46 I got very good memories of going out with my grandad on horse and cart and then a flat back scrapping early till late 80s around Notting Hill and London . Leaving 5 am on a sat n sun pack lunch in one hand little club hammer in the other to smash taps off the iron baths and break up the old iron guttering . Man I miss him 😞. You don’t realise when living the best years of your life. Prices was good in them days the flat back would be stacked high with copper iron lead …. Going to different scrap yards to off load certain bits, and given my little wages prob £20 but to a 7 year old that’s a lot . Good luck to you all the best Im a new sub 👍🏼

At least it wasn't a loss! Or costly rubbish clearance .

Keep it up, this was interesting!

Always interesting 👍👍

I was sad to see it go, got married there in 2002😢

Is it worth doing with a small van ?

not a bad weigh in.

Free is always best

What colour is the hayter green iv got a harrier 56 and cannot find the correct colour or even close Colin I emailed hayter and they asked me for d.o.m and serial no I sent it and nothing,I tried b.r. green and it's too lite any help would be greatful 👍👍

Thanks for the videos I enjoy watching them

Do couple days Street scraping then couple of days sorting to weigh in

Nice haul good video thanks

What is in them bud?

Good video bud thanks

Hello bud some good find keep it up mate . What was wrong with the van on last video?

👍👍

👍👍

All lights are flashing on my washer I cleaned the waste & still have all lights flashing & it won’t finish the cycle so I presume it’s a different fault on my washer

was this just a run to clear some crap?

Hello Colin, it's always good to have a clear out of odd bits of scrap to make room, all the best James

How do you get the plug out? Mine won’t start and it may be the plug. I have bought new battery today then it ran then cut out and now can’t get it started

Nice relaxing video colin, good luck buddy☘️👍

If a swing arm is replaced and given a q plate can it go back on its original plate ? Cheers Allan.

Which brainwave sactioned these ideas? I'd love to know how much fly tipping actually costs each local council per year. You'd be forgiven for thinking we'd lost WW11!

looking well colin 👍

Well done Colin, always great to see you on here. 👍👍

Nice, dude. I'm working on a '46 Willys with a 12V conversion and have been chasing gremlins. My solenoid was grounded out and sending 12V everywhere. I didn't know these needed to be grounded, though!

Handy van 👌

Well done Colin, that looks really smart

Very snazzy

Wow 😮 looking good 👍 thanks for sharing this today and Happy Sunday 😊

Po still running a 59 combo round my way great economical little vans for fiat engines in em.😅

Where is the starter motor solonoid on this mower ?

Just do it

Ey up colin, good to see you back

Ahh there you are, nice to see you matey!

Nice to see you back Mr Colin👍👍

How to engage the blades, do you press the clutch before moving the lever

Hello sir . Thankyou for helping us all out . Ive been trying to fix my friends hayter 41 . For the love of it could i get it to stay running . So started to look at that choke part you showed us ...found that dam thin spring was off the choke part . It works

Your shed is worse than mine haha, have you sorted it all out yet mate?

I'm struggling with my Hayter LT324 as the cutters won't engage. Tried, The seat sensor Diverted valves on the cutters, New toggle switch Checked all the fuses but now it looks like I'm going to have to take it in to the professionals

Shocked the piss out of me when I did this…

Thanks for the explanation, why are both belts so slack on the pulleys, even when new please?

Thanks Guy, that's very helpful, just been asked by customer to investigate his harrier 48 drive slip/no drive after working OK for a, while.

Damn and it was a pro's saw?

Hey Colin nice video mate keep up the good work

Hi there can you help me I got the same saw as you got k650 mark 3 but why have you got a decompression valve blue thin and on mine I don't have one Cheers