วีดีโอ

I have a 2005 nissan titan with this rear end😮 whats the gear oil weight & capacity??

Thank you for making this video. Helped a lot!

Thanks for the video! I hear the M226 is prone to leaking, so wonder if low oil had to do with the failure.

Is the PCM located there also?

For anyone who knows this stuff. In a reasonable shop.. what should this job cost to have done??

Sir, you are a God send, you save me a lot of time and frustration, thank you so much for taking the time to do this video, God bless!!!

Holy smokes! I had a dead mouse in mine 2.... Thanks for the video

Next time you replace your timing belt, invest in an OEM pump, ditch that aftermarket garbage, and you will likely never have to replace it again. VG pumps are not driven by the timing belt, so there is no risk of a failed pump destroying the engine, therefore it's not a necessary component to replace when replacing the belt. Unless you run aftermarket, unreliable shit. An OEM pump will last through multiple timing belt intervals.

How much did the ride improve with the Bills on the middle perch setting?

Seriously had the same problem! Wtf? Thank you so much for figuring it out.

I know its been a while, and you don't have the car anymore, do you remember if you had to drop the transmission to get the sensor out? For some reason, its hard to find that out on google and youtube.

i love you you are my savoir

Where is my BCM gonna be located in my 2016 Nissan Rogue?

Thank u. Really

Hello, I know this video is old, but I have a question if you’re able to answer. The sensor to the left of the speed sensor in your thumbnail. I got under the 93 z32 I recently purchased and found that sensor ziptied out of the way toward the rear of the transmission. Is that the turbine revolution sensor that is supposed to be located up toward the front of the transmission at the top? I haven’t been able to pull the exhaust off yet to be able to access the top of the transmission and was wondering if that’s where it’s supposed to be. Thanks in advance.

Thanks man

Great video! Looking to install this in the next week or two. I see the installation instructions want you to measure before installing them, is that necessary? I didn't see you mention any kind of measurements prior to the install.

Thx for the video. I'm currently ordering everything to do this myself in my 91.

welding with no gloves thats ballsie ;p

The orange wire on the radio is the illumination wire to dim the stereo when headlights are on. It goes to the Red wire with blue stripe on the Z.

That’s right brother I love your video. N f yeah. U did fkn AWSOME thanks.

Thanks

@ 9:30 nice save!

Hey man so i have a 94 nissan 300zx i wired a new radio i have 3 blue wirrs and a black wire and have no clue where they go blue goes with blue but does the black wire connect to the ground wire in the back?

Your first waterpump( bad one) what brand? Or where did u get it? I got one today from rockauto, cheapest one($20) kinda sketched if it’s the same)

I'm so glad this track is being revitalized. Short track racing is so strong in Virginia and N&S Carolina. This historic short track will get to provide amazing racing again soon. Can't wait.

this is the best instructional vid ever on the m226 rear end

Just came across this video and great info on the speed sensor test, nice detailed presentation. Question I have a 1992 300zx NA manual 2 + 0 and the OEM speed sensor 25911-30P10 is discontinued but they have the TT one 25911-40P10 that the dealer says will not work even with gear change. You note it will work in the NA with the gear change on the TT shaft. Is that because each has the same calibration of AC voltage generated vs RPM? Or slightly different and will not mater for the speedometer? Thank you very much and appreciate your comment Pete

I wonder if it’s the same with the 2018 rogue sport.

Thank you very much you really did it, I have problems with no starting or cranking yes there is no video related to this, now i l=know where to find it , yuou are a life saver Gabriel.

Thanks for the vid man. My z is making the exact same blowe noise but still works, gonna give this a go instead of buying a whole new one

One of the best videos on the M226 rebuild/replace! Thank you! Rebuilding my 2012 Titan using a Yukon DuraGrip limited slip differential. Quite the endeavor, especially when I found the reason my diff broke was that someone was in their and did it all wrong. So my shims on the existing pinion were all wrong. Had to revert to trial and error on the shim settings.

2005 bent RR axle. The e-locking diff axle is a pain to find. And then UPS loses it. A big ass axle SMH

the pinon bearing is not that expensive. why use and old one the first time. to save $25. and having to do the job two times..

I’m looking for a rear end for an 06 titan 4 x 4 Eli with the 336 ratio. Any luck or know where I should start? I’m in Missouri and have called every salvage yard around.

Just the video I was looking for!!!

Ayy I just bought a '94 NA with 280k and I'm swapping out basically everything. I'll be sure to check that sensors power output. Thanks

It would be very helpful to have parts links required to perform this task. Everyone is planning on doing it. Links could save time and frustration. Love your videos.

What lines are you using?

Happy for yall!👍🏼

How can I replace my diff lock solenoid on my Titan pro 4 x cant seem to find anything on how too ? Can I just unscrew it and screw a new one in ?

The hero we needed 🇺🇸

I need to do this, did you have to remove the door card to get to the mirror cable connection plug ?

So exciting!!!

I have a 2020 armada platinum and just want a limited slip OR locker of some type. But no one will help nissan says it can't be done. The companies that make lockers and lsd say they have nothing for armadas! Please help me?

I had My car keys stolen. Had to get a new fob for my 2015 Nissan rogue. When the guy came to program it, it wouldn't work. He said never had issues before. $420 down the drain. But he said might need the bcm replaced... Any ideas that might help so I don't have to spend an arm and leg to get one and it b a bust as well?

i bought some used tein and i think im missing pieces, whats the odds you still have your instructions?

Hi, your video is pretty informative, my spider gears are delaminating so I'm rebuilding it. You mentioned at the end of your video that you could source a factory carrier if I understood you correctly but according to Nissan it doesn't exist anymore for the M226. I'm going with a Yukon DuraGrip limited slip and their master rebuild kit. My ring and pinion are still good.

Hi do you have the part number or link to get a new one

Do you happen to know what you torqued the carrier bearing caps and the pinion nut to as a final torque