วีดีโอ

Thanks to TH-cam for making me plumber, electrician, pilot, doctor, engineer and much more

So you have to drill the holes yourself?

The wall where I'm going to glue it has moisture when it rains, and is it recommended to do the waterproofing beforehand?

I don't usually comment on videos that have helped me, but I have to give you a HUGE THANK YOU!!! I used this T15 torx to remove a damaged schrader valve from my car's air conditioner line. This work perfectly. Thank you again.....

당신은 최고입니다. 감사합니다. 한국에서 도움을 받았습니다.

Karate Movie

I have had to recommend a few sensors due to this issue and I always feel bad because of how much it cost for a simple issue. Thank you for taking the time to figure this out, I will try it out next time instead of hurting someone’s pockets :)

informative and useful, thanks!

After watching your video I fixed it.many thanks.

Ghastly robot voice. What IS the point of this tomfoolery - get a live human, and do a GOOD job instead of a crap one.

You deserve more than a like!

What mortar are you using to adhesive the drywall ?

What mortar are you using to adhesive drywall on the bricks ?

a water reducer is in simply terms a quick closing valve. it will surely protect from the high pressure surges that are in the main pipe, in front of the regulator (since his main job is to reduce the pressure downstream) but it will also create or amplify/contain the water hammer blows in the pipes after him. i actually read in some instruction of such device that the installer have to provide a way to prevent this phenomenon when installing their product (by installing a small pressure vessel after it (a 2 litter one or something small that will deal with the increasing pressure from quick closing valves inside the house or the quick closing of the regulator). when the length of pipe after the reducer is not very short, the phenomenon is not very visible, the pipe is absorbing this blows, but i personally experimented this by mounting under a sink a pressure reducer, and 2 glass filters. since the length of pipe was very short, rapidly closing the sink valve will create a water hammer effect that will be contain by the pressure reducer in that short length of pipe (the reducer will close since the pressure after him will be greatly over the set one). the victim of this behavior (even though i knew this) was one glass of the filter. twice). then i installed a 8 litter pressure vessel (exaggeration but didn't find a smaller one or a water hammer protector in my area) and everything is ok now. sooner or later, if u don't have something weaker to break, and is just pipe, ... the pipe will break, or the joints, or the flexible hoses of the valve, something will brake from those blows.

I just flushed the water a few times and it fixed itself...

U didnt show us how to turn it on..

If i fix the drywall exactly as you , the drywall can be plated with tiles ? i have to hidde some ppr pipes in bathroom...

This is brilliant. This can be diy built with furniture struts or even cable wire anchored to the back wall and attached to the clothes rod. The length of the cable determines how far the rod will lower

The water entering the room is not always ideal; mechanical impurities contained in it can do a bad job. A mesh filter for mechanical water purification can protect and extend the service life of plumbing equipment and household appliances.

What is the purpose of the disturbing noise n the background? Annoying, bye. bye.

I'm having a hard time removing the protective ring because it only slides my tools how to easily do it

I wished you had mentioned how pressure reducers can Create a Closed Loop system, and possibly having an adverse effect on water heater pop off valves without installing an expansion tank?

I honestly don't understand why you don't have more subscribers. The level of research put into these videos is sooooo good. I just wish you would also put a list of recommended brands for each appliances at the end of the video or in the description box or something but all in all, you're doing amazingly. I really appreciate it!

Przydało się . Pozdrawiam.

Thank very much for sharing your skills

Thank you so much! Your video prevented me from making a huge mistake!

Did not work

Son watch this video to remove the value core

What kind of milling router is that ? Great video! I appreciate it !

shitcan the AI

Sir can you able to send me any of your drill machine that is not useful for you now I will be so thankful for your help 😢 Please any drill machine your choice 🙏

What’s the name of the glue. And where I can get it ?

Hello. what kind of glue do you use for it? and what do you brush it with before?

I've worked on tires, and this is something I'm going to try in the future. The issue I see is that when the core breaks it's usually due to corrosion locking the valve core into the valve stem, and when you crank on the tool, the core snaps. This corrosion also weakens the valve stem itself, so be careful when using the torque head tool you don't flex the stem or it can snap (I've seen people snap them putting air in their tires.). but as I would be recommending to the customer to replace the TPMS stem (if possible not all sensors have a separate valve stem from the body of the sensor) /sensor anyway, I'd give it a try and if it A: didn't work due to corrosion locking the broken core into the stem, or B: flexing and snapping the valve stem then I'd be replacing the part anyway. I will definitely have to give this a try in the future.

Is it helps to speed up water flow ?

Can you provide Drawing for the milling dimensions

Indonesia menyapa

Although it's machine voice, the content itself is really helpful. Thanks

This is the best video i watchted, choosing the right stove....now, i know exactly what i want, THANK YOU😊

answer at 1:30 LOL

do you use highspeed or lowspeed

Can you provide a link to the primer?

Thank you

Where can I buy these?

Hello ❤ my name is Jacques, I need some details about this practice because I'm so interested to make this kind of concrete vibrator

nice job friend

good, we make this furniture screw bolt machine

I get piping hot water in bathroom wash basin and kitchen sink, but only lukewarm on bath mixer tap even on max hot setting. It's not a thermostatic type type. Any advice, please.

Awww Sooo PRECIOUS 😊❤

How do you remove this? I can’t find anything on it and my home had someone glue it on top of unpatched or cracked cement, Which created mold..how do we fix this?