วีดีโอ

It was some bad ass stuff then! I figured it was bad rust that had been cleaned out of it at some point

They are very good saws, Very heavy which I think makes them smooth running. My other saw has a gear stripped that raises and lowers the blade. I'm hopeful that the one out of this saw will be the same and I will just part this one out. We will see.

@@richardclack3007 Just got the arbor bearings out. One size bigger than the Craftsman/Emerson bearings as I recall. Will replace and reassemble. Excited to get this up and running. Then...try to find a Unifence (good luck there, buddy 😂)

Stay tooned

Hey, thanks!!!

Glad you enjoyed it

It's from the early 70's like all the old stuff

They are made to make a joint stronger and more so to line them up evenly. This was not lining up the two pieces correctly.

Thanks for letting me know that! Every Vacuum is a dust extractor to me. Would be nice to hook it to a saw easily. Oh well.

really? that's so disappointing. this would be the perfect dust extractor for my micro workshop. have you tried using it as a dust extractor?

@@luns486 I personally have not. The hose will make it hard. It's not flexible enough in my opinion. I have just used it for general light cleaning. I am sure it would work on a limited basis

@jack12343 Thanks Mate! Riots is correct! 😜

I just got one and it's actually advertised attached to the 36v compound saw which I have and why I got one but it's very annoying how every makita tool has different size dust port it just stuppid.

Same here. My biggest problem is the accuracy of the stop gauges. If you move them it takes forever to get them right again.

😂🤷‍♂️

Give me $1200 to go buy one and I will make a video for you! haha! I'm sure the Festool blows anything WEN out of the water. If you wanna pay for it.

I thought the same thing. That is usually the problem when a blade smokes

I took the unit to my local sharpening shop, and as I suspected the blade was terribly dull, hence the smoking when I used it. Kind of sad that WEN would supply a brand new tool with a dull blade. I’m using it on spruce, not even a hardwood😖

seems like it would be off balance or something wobbling? Who knows I think all these tools come out with different issues or they work

The guide fence of the tool is resting on the top of the board. The board is on the table but the bottom of the jointer does not hit the table.

Tell me how that is. Tool cuts angled cuts. 🤷‍♂️

Maybe thin skinned as well, lol 😂

hahaha I guess I learn something new everyday!

Yah I’m kind of becoming a woodworker I’ve seen lots of woodworking videos and most people use shop vacs instead of those bags but I use the bags on orbital sanding

@@craftsmann3845 I use vacs on my sanding. Bags don’t catch all the small particles. I usually throw those dust bags away. Everyone has their own ways don’t they?

Let me know how it goes.

@@FM.05.05. mine was just fine. No alignment issues. All the adjustments worked as expected.

@@richardclack3007 sorry I missed your reply. Mine was perfect. No alignment issues. All the adjustments worked as expected. I got smoke on the first couple of cuts but that subsided as well. One thing I do like is the dust collection. Everything goes in the bag. So if you were to use a shop vac in place of the bag, all the better.

@@awlthatwoodcrafts8911 Glad you had better luck then I

Yes, for sure it was wood smoke. Didnt leave burn marks on the wood though. My guess is because it wasnt cutting a true slot. it did clear up when I drove it in faster . Who knows?

Let me know how it goes with yours.

@@richardclack3007 I got the smoke on the initial cuts but it went away as I did more testing. Mine is parallel. I made different cuts adjusting the height and measured each one at both ends from the surface of the workpiece and they all came out parallel to the surface. The one thing that is pretty impressive is the dust collection. Everything goes in the dust bag. I saw nothing on my work bench. When I tried to test join a couple of pieces, I screwed up and didn't tighten the bevel adjustment enough and ended up with slightly angled slots. I also had to adjust the depth control screw as the "0" and "10" slots were not deep enough to allow a biscuit to go half way into the slot. Other than that, I'm happy with the one I got so far. We'll see how it performs when it gets used for a real project.

@@awlthatwoodcrafts8911 would you still recommend this to ME?

I’m new to woodworking

Good deal!! Thanks for letting me know!

Definitely a possibility..

@@richardclack3007 Way to man up! Well done!😊

Haha. I will talk to my producer about doing more

I don’t know and not being critical by any means but other videos I watched say that you should reference off the wood you are cutting and not your work surface. Maybe you were I could not really see in the first video. I did enjoy your video and was considering a WEN tool but I will likely research more about them as I too have never used one.

@@kerseystealthkills You are correct. It has a fence that lays on top of the wood that is getting cut. Then it has an adjustment, where you decide how far up or down on the surface that groove is cut. The slot was way out of whack and I didn't notice it in the first video. I still don't understand why it smoked, I watched a lot of videos on them and never seen that.

@@richardclack3007 yeah I haven’t seen that in any other videos. I am still undecided on which one to attempt! And yes that smoking would have been concerning to me. Was it wood burn or electrical smoke

@@kerseystealthkills wood smoke. Plunging the jointer fast solved it, but doesn’t seem right. Going to spend a little more on the next one. Stay tuned! Thanks for watching.

I think the speed is key. At this price point im surer the blades isnt top of the line either. One day yi will try a new one. Thanks for watching!

Yes its that time of year again. I didnt grow up in VT, so I still love snow! hahaha

So far so good. honestly Ive just set it to 3/4 material and thats all I have used it on so far.

They use ipads

shes old

i will give the realtor your number

Thanks for the update

I will upload this years parade also if youre not able to fly up from the islands!

@@richardclack3007 à

I should get a video from the island parade, I know a guy dressing monkeys up like elves. He taught them to pass out bananas !

Yes ! Its a man thing!

cvvvvjhvbbbyuikmknggssvjlVfhkvjbvvbbv nkcfgugcgbgďdtg

hhjjcfgggghgvvvccdyyeyufrrrrvbhcjnvgvv. zsyg