- 8
- 8 303
Nathan Beisley
เข้าร่วมเมื่อ 14 พ.ค. 2011
วีดีโอ
Polaris 400L 1994 4x4/AWD Hillard Clutch and bent axle part 2
มุมมอง 1024 ปีที่แล้ว
With this video I removed the armature plate and replaced it because as seen in video 1 it didn't have enough holding power to fully ramp the sprague.
Polaris 400L 1994 4x4/AWD Hillard Clutch and bent axle part 1
มุมมอง 1.7K4 ปีที่แล้ว
Polaris Hillard clutches are not understood well and mine has been a bear to figure out. I have a bent axle and it is uncommon so I wanted to show what to look for, also see the clutch does not ramp fully. Video part 2 has this assembly repaired with a new armature plate.
24vac control transformer grounding
มุมมอง 1.2K5 ปีที่แล้ว
This is just a crude to the point video hoping to speed up someone's day. Remember to isolate one wire of the secondary/24vac side of the transformer to do this test. Some transformers are grounded through the shell of it but this one was not. This repair your seeing me do while making this video was caused by 24vac hot being confused with common/ground. So when the 4-20ma wire had been connect...
Walt's magic carpet on 3" ball pit balls
มุมมอง 495 ปีที่แล้ว
300 3" ball pit balls and a cardboard box, this is what a Sunday morning looks like. No balls where harmed in the filming of this video.
TRIBUTE TO KEN BEISLEY/ a little evil 2013
มุมมอง 7811 ปีที่แล้ว
On easter sunday 2013 Ken Beisley had a quad roll over on him causing a serious injury to his chest and needing time in the ICU to recover. Six days to be exact, I had brought my homemade rail up for him to view and enjoy on easter and decided the next day, april fools that I would scare the girlfriend on video and put it on his facebook as a welcome home surprise. That screaming is real folks!...
A LITTLE EVIL 2010
มุมมอง 65913 ปีที่แล้ว
HOME MADE SAND RAIL RUNNING, SBC 35O, TH400 TRANS, FUEL INJECTED, DANA 36 REAREND FROM AN 87 CORVETTE, 24 INCHES OF WHEEL TRAVEL, AND A BEER KEG FOR A FUEL CELL, WHAT A BEAUTIFUL THING
Excellent video!
Thanks!
You said DC common. Did you mean 24v AC common?
You should have move the camer futher back so we couldn't see what you were doing or see the set up that you had going on. ....
agreed
Was thinking that it might work - so checked YTube and lots of people are doing it. Will be a cheap, quick and easy way to drive posts around between the wooden posts. Thanks for the vid.
Thanks - was thinking of it being heavy - but physics don't lie.
What size jack hammer and where did you get the bit for the t post? Thanks
Thanks for the detailed response, I have hard clay soil with no rocks. Do you think it will drive a t post in that type of soil? I have a welder or I see they make a bit for posts but it's around a 100 dollars with shipping.
Nathan Beisley for sure it's better than by hand. I have hundreds of posts to install, I need a better way. Is your bit holding up to the abuse?
Nathan Beisley that's exactly my plan, I have a 3500 watt generator. Thanks
@nathanbeisley And I like the song too.
@nathanbeisley Sweet, keep making videos. I'm going to the dunes next weekend and should have a new video up a few days after. My brother has a 2 seater sandrail with a worked 1835cc VW. I'm taking my go kart to run in the forest behind the dunes.
Fark! What a beast. Can't wait to see it going hard. Just hope you don't blow the engine, you could lose a leg!