วีดีโอ

I have a ET blue remote, no matter how long I hold in the button the remote mode doesn't seem to change. I think I have by now depleted the battery

Hi there. How do I setup my wireless infrared beams to my dc blue advance garage motor

Previously the range was much a distance, after the neighbour fit WiFi my client have this short range problem. Can someone tell me why.

Why I have a short range on my 1 Ch Rx less than a half a metre.

Drive ET 500

500

500

500

@renaldonel8897 hold in the button you pressed initially for the motor until it flashes again then your remote will work again.

Hi. Can you help with instruction for DC BLUE PLUS🙏🏻🙏🏻

what does 2 mean?

Simple, clear and effective. Thank you!

mine says IRB then won't open

Drive 500.600 & 1000 how to add Rimotconro

Excellent explanation 👌 Clear and easy. Thank you.

The motor have power but doesn't want to open ore closed

My Drive 500/600 have the following message: Lim fault. Open manual release. How do I fix this?

How do i add a master remote to a receiver if I can't find the main master remote.

Twnfo drive 1000 cuando la energia se corta y vuelve sale error y los controles no funcionan pero cuando desconecto la energia y la bateria por un par de segundo vuelve a funcionar los controles que puede ser ??

Nice

Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks

Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks

Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks

Good morning dear Sirs, I have a problem with my Nice 300 stepper motor, it presents an error “ES” whenever I configure the beam limits before reaching the end of travel it stops and displays this error I would like to know how I can solve it . Tanks

My gate don't open if the battery is flat even if I have power. I want the gate to open with power..power 1st then battery

What do you do if it beeps eight times rapidly after programming instead of running?

I have a p flashing on my motor

Does not work

Nice ,short,clear and very informative

I have tried adding additional remote, and keeps failing?

Please provide wiring diagram for pillar light

I have a new ET Blu Mix remote control however the button that I wish to use for my garage door has been held for longer than 20 seconds and has converted that button from ET Blu Mix to ET Blu. How can I return this button back to the ET Blu Mix format?

The lighting control feature is something that's not common knowledge, perhaps it's not marketed sufficiently?

You Deserve a Bells 😎 🙏

Good day. Is this a new feature to the drive 500 motors by Nice before you rebranded from "ET Nice" Is there a vibration sensor on the motor that allows a remote output?

Your videos are so helpful! I'm wondering if u can assist me... my friend and I added a remote ourselves and it confused thr system... my usual button to open the whole way became a pedestrians opening and now all remotes don't work anymore. The motor always says holiday lockout

My pins won't short out. Wat does that mean?

Îs this posible on a barrier gate?

What is this holiday feature? It is a old version of gate but no one told me.

❤😂

Hi, please assist if I press close on the remote it will go down and as soon as it reaches the bottom it will automatically go up again and open. I think the setting went out but don't know how to reprogramme it.

Hey can you assist me with factory d300gate motor

How to factory reset d300 gate motor

😅😅😅😅😅😅😅😅😅😅😅😅😅😅😊😅😅😊😅

Hi there. My gate with a 24v 3.5ah battery stopped working. Friend had a new 12v 7ah battery at home and I tried that but it didn't work. I thought it might with ohm's law making it same power, but to eliminate any other issues, can you confirm that a 12v definitely won't work

Do I have to have a beam installed to use auto close mode or is there a resistor to bypass the beam option?

Massive

What an easy and wonderful way to learn thank you

What does rel mean on display

How do I deactivate safety beams on my ET 500 and do I have to remove the wiring from them?