วีดีโอ

A lot of wrong things there: passing the piece with barehands (a small piece), the face should be flattened before the edge, the push block was used backwards.

Lovley ❤

Merry Christmas x

Merry Christmas 🎁⛄🎁

looks amazing

Just recently found your channel and hit subscribe straight away. I love the down to earth style of your videos and thank you for showing that woodworking is not "super simple". I can relate so much to your frustration and disappointment when things go wrong!

Thanks for sharing. Lidl offers a crazy discounted price on the Parkside Planer Thicknesser here in CZ, and AFIK that's basically the same machine rebranded. I think I may get one of those just to see how it holds up.

I think with ur band saw, try not use a fence...im thinking it binds up, then stops the saw.... free hand cut it, it will be faster than the circular saw

Not all squares are created equal! I had a try square like yours a few years back, and it was WAY out. Worth checking

Hey Woodsy - love what you're doing, great channel, keep it up. Not sure if you noticed, but on top of our router bit, there's a hex key hole - you can take the bearing off and replace or clean it without risking losing a finger! All the best

Good, helpful video for people with this machine. Just a thought....please roll your sleeves up, it's so easy to get caught in those blades when running stock through (even when using the guard).

Amazing 🎉🎉🎉

Hi mr woods u teach me every Thursday last lesson

Hi Mrs woods

bikes are crying

I'm curious, Woodsy! At what stage do you decide "this isn't quite CUTTING it?" 😂

LOVE IT! What's that application you're looking at for the design? Or is it just an image you've found with dimensions? Absolutely love your work, Woodsy! I'm here for the ride!

Hi I really like this and a new wood wannabe seems doable for a novice ….. but I keep reading that oak isn’t good as a chopping board owing to its open grain . ??

I have the same machine as you have here and get most of the same problems, changing a blade is no fun at all and you get frustrated with it after a short time. I can not cut a straight line with the guide either, so I do it by hand, bit difficult when you are only partially sighted (vision in one eye only). A comment on your video, / Always disconnect the power before working on it and don't recommend using the allen key to overide the safety devices. I did see at one time you did not put the Plastic/metal (now) guide down the left side before running it and you didn't show fitting it at all for final scene. Unfortunately some of us can not afford a superdouper Bandsaw and have to settle with the above sort of level. Anyway thanks for the video, you have shown me where I have been going wrong with replacing the blade Keith

you should be doing the face first and then the edge.

so after a month how is it ? was thinking of getting one

Why don't you always turn around your table top with your router in the counter-clockwise direction ??? 😬😬😬

Hi

Liked your video, haha. Thnx for the explanation. It helped a lot.

Looks great!

Looks fantastic woodsy! A masterpiece

try rufus

I thought the blade guard should go over the piece 😅😅😅

Try using a program called Recova, its free too. Ive revovered many photos using that on sd cards and hdd over the years.

That rail went on satisfyingly :)

Nice bit of kit. I've got the Triton spindle sander and that's been a useful bit of kit. 👍👍

well mate if you were not able to adjust its direction, blad-play within grips, it does not mean its a piece of crap? did it occur to you that your skills are probably crap?

Free-hand routing straight lines is so hard!! I would definitely have had to use a fence or straight edge of some kind!

knife boxes?

you got me with legs.. i line to put casters and so i can move them easely around

I can confirm that this machine is not appropriate for long straight cuts. I've set the guides to be close as possible to the blade, and applied a fair amount of tension, so it's really straight, however it still deviates during the cut. It works ok for pieces about 10 cm, but bigger than that it's impossible. NOTA: I'm using the blade that came with the machine and I have not tried other

Lmao hope u enjoy Ur holiday!

Dual gifts 😂 you could dual wield them and increase efficiency hehe

Making a cot, something you need to tell us?

i totally get your excitement! thanks for sharing!

I immediately assumed it was going to be Gwyneth Paltrow’s head.

You're supposed to shift your weight as you move the material through the machine. Press the back of the board when you go into the blade, and shift the weight to the front of the board after the blade is past the center of the material. This way you'll be referencing off of the outfeed table as the board exits the blade and it won't be able to tilt back into the infeed table.

Down-cutting blades are for laminates, worktops, etc where the up cutting blades will leave a fractured laminate on top. I don't know why you had problems as I use whatever I have to hand or is in the jigsaw - except when cutting worktops.

Cool 😎 thanks for sharing 👍

the 250W motor seems so cute and dandy but in the catalog they recommend a 15 minute job with pause for the motor to cool down and I was wondering if we cold change the motor to more powerful one. I found in my area a couple of motors with 2.2KW, 1.8KW and a 1.1KW for about 70 euros each. Also in my shop I have 3 phase power so having a small 700W motor with 3 phase is also possible but a bit more expensive I guess. I do believe than even a washing machine motor would be better than the silly 250W one but hey, if it works it works

Get some dowel pins then work out where the struts have to go then put dowl pins in holes in struts & simply press against the joining bit. They leave small indents where the dowels need to be drilled

hi, if you strip the jig you will notice that there is a slot in the plate that will locate off the existing dowel peg

Cot

You sound very excited 🤣

Hi, just a question about hand planing. Why aren’t you using the einhell to flatten the faces, is it not up to the job? The reason I ask is because I’m thinking of buying the same model but if it’s not up to planing the face like your doing by hand I might have to look at something more expensive..