วีดีโอ

I thought I was the only one outside of England that said Bob's your uncle. 😂

Ŵęŷüïœæßłñçž🌺

🐱

Doing this will allow key removal while in gear thus allowing car to roll! Emergency only!!!!!!!

Subaru has extended the warranty on this issue! Do this in emergency, takes literally 12 seconds! Ok maybe a minute! Your key won’t beep if left in ignition with door open! I’ll look into the real issue when I get time or if the dealer will warranty my 2016 legacy with 75k miles!

Ahh yess, this just happened to my 17yrold dremel.. 1st the lock button was slipping. Now it wont engage or disengage! ..i dont have a mill soo i ordered the lock shaft part..thank you!!

I'm having low voltage to all of my outlets. I checked the breaker box with a meter and it reads fine. Any help would be appreciated. Ty.

How much did you pay for this machine?

Please distinguish the words "plug" and "outlet" ("receptacle"). If you call them both the same thing, we can't understand you.

240 volt plug

did you get the lathe for free?

Thanks

Part number on Aliexpress is SF-HC30A

wadup train

Thanks for this info, have one outlet that should be 230v but it's at like 150v, thought something was wrong with the cable but now I'll try replacing the outlet

its a 15 yr old machine using 25yr old deskcnc software

Can I contact you? I tried converting anilam crusader using the servos. This is what I have been thinking about going to. Would like to know what motors you bought and any problems u had.

Amazing work!

Fu

Thank you for the time to do the video it helps a lot 👍🏻🤜🏻

i have gfi with the same problem. thanks

Ive just moved into a new house and sure enough, when i plug my vacuum in the thing barely sucks at all. Im wondering if maybe a bunch of the outlets in the new house are weak, or broken? Strange..

Bob's your uncle. lol Thanks my man. This was a quick breakdown with solid stategy. Now if I can just find my meter...

The reason for the low voltage (94v) is that the wires in the wall are too thin, or too long, or there is another big high-wattage load in parallel with it, like heater, air conditioner, coffee maker, etc. A lot of old homes have the old-fashioned cotton-covered wires with 2-prong outlets. Some dishonest electrician ran a jumper wire from green (ground) to silver (neutral) and put in a 3-prong outlet, to deceive new homebuyers. I am NOT saying this happened in your house, but a lot of crooked home sellers do this.

Thank you so much this really helped diagnose my issue! An outlet had a loose connection and caused the following 3 outlets to only output 80 volts.

Just a tip - when compressing the caliper pistons, crack the bleeder screw instead of pushing that dirty fluid back into the system. The filthiest brake fluid is in the caliper, so squirt it out through the bleeder.

Thanks!

I've got an Ender thats skipping now for 5 days. No fix has worked. I'm really starting to think these are junk printers and we made a huge mistake buying it.

Your outlet is not parallel it's in series to be my guess or some weird resistance.

Thanks for the help. You solved my problem. It's amazing how a plug can just go bad.

There was plenty of room to cut off the hack job that someone tried to solder the ends. I then sanded the ends to get a good connection and wrapped them around the terminal like they were meant to be. Tighten the nuts and put it back together! Man this thing can lay a bead! Beautiful welds for a AC 250 amp welder!!!! I should of fixed this long ago!

Seems to be the voltage divider from aliexpress yes

On mine the holes are stripped

Thank you for the video!! Fought my rear rotor, until I watched your video.

Is this voltage divider board is the one sale in aliexpress?

ρ尺ｏΜ𝐎ᔕᗰ 🌺

Thanks for showing the guts of this lock. I had to do a locked up surgery to get mine to open. Couldn't have done it without seeing this. Amazing how a little lubrication can keep mechanisms working!

I used the floor jack like a reverse drill press, used good drill bits and used the hydraulic pressure to do all the heavy lifting! Worked amazingly well with this low geared drill hog drill by Milwaukee! I put my knee on the bar and my left hand to activate the switch and my right hand to pump the floor jack! Like my best TH-camr says…. Keep your 🍆 in a vise!

You on Xanax or wat

Very helpful video. What brand and where can I get one of those divider boards?

Thanks for the idea! I filed down a pop rivet in a drill, looks almost the same, should work haha

Your video was very helpfull to me. thanks a lot.

Hello, what post processor are you using for fusion 360? What controller do you have?

Hi. I am facing a task of setting up an natively manual plasma cutter with an automated system (THC and so on). Problem is that I have a High Voltage start plasma without a divider or Arc Ok signal. So as far as I understand Your setup You are using an external divider to get that 1:50 for THC readout and You wired it to bypass the need for additionl Arc Ok output, so that it is basically always on as soon as the Start button is triggered? Eagerly waiting for Your response.

Hi do you still have the old imservice cnc

Very nice setup

Thanks for sharing I have the same issue in my house.

Who’s doing all this

What size cable duct are you using

Thanks, but electrical instructions are like trying to understand someone using a foreign language and me trying to understand.