วีดีโอ

Chiar am mâncat uitându mă

104 la condesator este 100 nanofarazi

Excelent video pentru incepatori! Bravo! Ca tot ziceai de osciloscop, vezi daca videoul meu despre asta te ajuta sa-l intelegi mai bine. Mult succes! 😁

Unele sunt unelte cum e letconul si pompa de cositor altele sunt instrumente: multmetru si osciloscopul.

Foarte util acest videoclip, multumesc @Iusu.

Bun materialul, apropo pentru ce ne poate ajuta sa vedem unda daca este patrata sau rotunda? Poate faci un material video cu ceva exemple si unde se aplica?

Felicitări pentru video

recomand!

#include <AFMotor.h> #include <Servo.h> // Create motor objects for all 4 motors AF_DCMotor motor1(1); // Left-front motor (connected to M1) AF_DCMotor motor2(2); // Left-rear motor (connected to M2) AF_DCMotor motor3(3); // Right-front motor (connected to M3) AF_DCMotor motor4(4); // Right-rear motor (connected to M4) // Line sensor pins const int lineSensorLeft = A4; // Left sensor const int lineSensorRight = A5; // Right sensor // Ultrasonic sensor pins const int trigPin = 7; const int echoPin = 6; // Servo motor Servo myServo; const int servoPin = 9; // Servo signal connected to pin 9 // Line detection threshold int threshold = 530; // Midpoint between black and white readings // Ultrasonic detection distance (in cm) const int distanceThreshold = 15; // Stop if no object detected within 15 cm void setup() { // Set motor speeds motor1.setSpeed(200); motor2.setSpeed(200); motor3.setSpeed(200); motor4.setSpeed(200); // Initialize sensors pinMode(lineSensorLeft, INPUT); pinMode(lineSensorRight, INPUT); pinMode(trigPin, OUTPUT); pinMode(echoPin, INPUT); // Attach the servo myServo.attach(servoPin); myServo.write(90); // Start in a neutral position Serial.begin(9600); // For debugging sensor values } void loop() { // Read ultrasonic distance int distance = getDistance(); // If no object is detected within range, stop and start servo search if (distance > distanceThreshold) { stopMotors(); servoSearch(); return; } // Read line sensor values int leftValue = analogRead(lineSensorLeft); int rightValue = analogRead(lineSensorRight); // Debugging: Print sensor values to the Serial Monitor Serial.print("Left Sensor: "); Serial.print(leftValue); Serial.print(" | Right Sensor: "); Serial.print(rightValue); Serial.print(" | Distance: "); Serial.println(distance); // Line-following logic if (rightValue > threshold) { turnLeft(); } else if (leftValue > threshold) { turnRight(); } else { moveForward(); } } // Motor control functions void moveForward() { motor1.run(FORWARD); motor2.run(FORWARD); motor3.run(FORWARD); motor4.run(FORWARD); } void turnLeft() { motor1.run(RELEASE); // Stop left motors motor2.run(RELEASE); motor3.run(FORWARD); // Move right motors forward motor4.run(FORWARD); } void turnRight() { motor1.run(FORWARD); // Move left motors forward motor2.run(FORWARD); motor3.run(RELEASE); // Stop right motors motor4.run(RELEASE); } void stopMotors() { motor1.run(RELEASE); motor2.run(RELEASE); motor3.run(RELEASE); motor4.run(RELEASE); } // Ultrasonic distance measurement function int getDistance() { digitalWrite(trigPin, LOW); delayMicroseconds(2); digitalWrite(trigPin, HIGH); delayMicroseconds(10); digitalWrite(trigPin, LOW); // Read echo pin long duration = pulseIn(echoPin, HIGH); // Convert to distance in cm int distance = duration * 0.034 / 2; return distance; } // Servo search function void servoSearch() { for (int angle = 60; angle <= 120; angle += 5) { myServo.write(angle); // Sweep right delay(100); // Small delay for stability } for (int angle = 120; angle >= 60; angle -= 5) { myServo.write(angle); // Sweep left delay(100); } myServo.write(90); // Return to the center }

Un cacat de videoclip dar las acest comentariu inainte sa l vizionez

te pup iustine te apuci de vlog?

coaie sa vina printu ce cacat in schimb arata bine bravo

Cine sunt cei doi băieți de la final ?respect+

Unde i sapca boss? Ma deruteaza chelia si nu pot viziona clipul vidio

Instrucțiuni neclare am dat foc la casa

Recomand

Un videoclip de cea mai mare calitate. Foarte informativ.

foarte interesant

Instrucțiuni neclare

Prost mai ești Iustine😂😂😂

Am trei role de fludor diferite.pistol de lipit vechi cu putere de lipire mare creion de lipit.sacaz si nu stiu de ce.dar nu se lipeste fludorul deloc .Oare sa ancerc si cu pasta de lipit??