วีดีโอ

This is what happens when boredom kicks in, sat at a service station waiting for the stopped traffic to start moving again

It's a steel boat. I'll be using polyurethane paint on the deck and epoxy on the hull

Been watching Jaimies channel for quite some time and always wondered how you got on, then found your channel which I'll be binge watching to catch up.

I had the bilges shot blasted which created a massive amount of cleaning, then painted with two pack coaltar epoxy. Removed all the treadgrip from the deck, cut the Dorado boxes off to weld up a couple of holes and started removing the windows and made a couple ready to go back in. Covid lockdown stopped play and a few other life things got in the way. Full on work will start again this coming spring and hoping to get in the water before summer. Till then all is paused and I'm working long shifts to build up funds for boaty bits. Lithium batteries being one of them. Following your channel for hints and tips x

@@Sailingon My house renos ground to a halt when covid hit as well. Starting them back up in the new year, trying to get it done so I can switch over to the boat refit. Fingers crossed you get in the water before me! Have you thought of restarting your videos in the spring?

@@TheDigitalMermaid I'm going to try and do more videos, I get stuck in and forget about filming which doesn't help. Eek just seen the time it's 12:30 and I'm up at 7 for work. Long one tomorrow 8am till 11 pm eek on the plus side takeout on the company, Thinking Chinese will be nice.

Thank you, pleasure to receive the famous salute your videos make us smile.

I didn't have any that fit in the gap. I now have an extractor which works really well.

They do. This is for cutting foam and the hot wire doesn't touch the foam. This cutter will be just two axis for fuselages. Will also run a lot slower than in the video.

This is just a test, I cut some RG15 wings last night for a Lidl. The linear bearings, screws, motors and belts are all from eBay. The design is from thingiverse but modded a little. I'm going to make all new parts on my CNC router to replace the printed parts and improve the design. Should have something in a week or two and I'll video it all.

It was slowly falling over. That's why it ended there 😁🤪

@@Sailingon I'm not convinced :D

I could do with a camera girl if you want the job 😉

@@Sailingon hmmmm.... I may have one or two cameras ;-) . Is the world ready to see you in 4K though? 🤗

p.s. You may want to think about setting u a camera to record some timelapse work.

Hopefully they will get better. This weekend I'll be removing all the deck fittings and windows to do repairs to the corrosion. Then prep for painting and replace everything. It's going to be next summer before I get back in the water.

It stumped me for a while, also the cheap impact driver although not great ,it did help. Now I have a bit more knowledge I'd be more careful putting something in the slot. I put a but on it and had to use a file to get the new impeller on.

@@Sailingon second that - if you twist hard enough the slot will open up and the shaft will be ruined.

Hi, my first comment 😁. These little models fly really well for a kids toy

I need to check my channel more often, I don't get notified when someone comments. It was like this all day and got a little stronger at night. Saw bioluminescence for my first time, was amazing.

If you have a bad day, the sound of the birds make everything better 😊

It's the same hull as a Bruce Roberts spray 38, all the work that needs doing is within my abilities. I'll be replacing the through hulls, seacocks and sturn tube dripless seal with a stuffing box. Antifouling and put her in the canal. A really good clean out then livaboard and work. New rigging, new head sail and painting. It's going to be hard but worth it.

@@Sailingon excellent, I'll stay tuned