วีดีโอ

Been a while since you have done a video. You ever doing any more?

I thougt it was shake and bake. Not shake and wiggle.

comment

Does this system you put on with the DBX mufflers have the hi flo cats?

The way Greg turned those knobs, I would bet his wife is really happy

Bullshit

Why does Harley always make the instructions so damn hard to follow? This tutorial is very, very helpful and easy. Thank you!!!

Found this after trying to do my 2012 RG Ultra fairing this evening. I like the idea of removing the headlights because I could not get my hooks to line up...forgive the ignorance but how do remove the lights and put them back in once the fairing in installed?

Great video gentlemen very simple & to the point! Thank You 👍

Does these come with hardware my stock CVo slips have the nut welded on the inside off the rear bracket.

Twisting that yellow thing literally doesn’t do anything 😂😂

Do you a video for installation of Trak Floor board Runners with for lights MYBY-0043 2022 ULTRA TRIGLIDE

Did you have to tune it with the slip ons

Where is mine on 2017 Road Glide? Can't find. Thks.

7:04 pm. Thank you. Great job!

Well, learned all about the back of your hand. Thanks for that. 🤔

I did this yesterday. It took a little over 4 hours, and when you say "We make it look easy" you're not kidding. In the end it is so worth it. Did you install the provided baffles?

Rineharts rule!😮

Ridiculously easy 2 install.

Came for the instructions, stayed for the muffled sped up voices :P

I purchased the HD Signature LEDs. The Dealership I went to had both the Signature & ProBeam on display so I used a light meter to see which one was the brightest. The Signature was about 400 lumens brighter than the ProBeam. That’s why I decided on them.

This is a load of bullshit lmao

You are a life saver bro! I was losing my mind trying to get the slack out of my M8 cables!

You don’t actually need any wrench when uninstalling/installing the heel shifter, there is a notch in the bottom that locates the nut and holds it in position. Just for anyone wondering, don’t use a wrench!!!

Great video, I have stage 1 with air cleaner, VH fuelpak and rinehart 4.0 slips. Getting stage 2 done this week, woods 555, S&S adjustable rods and S&S lifters. I am now also considering just getting these headers put on for a full exhaust. What do you think?

I just got rid of my Saddlemen Road sofa for a Mustang touring. Very happy with the Mustang

Did you need to get a new shaft? I have a 2021 RG and I want to add a heel shifter, but I have been told I need to get a new shaft because if I install a heel shifter. The shifter won't clear the primary. Did you find that to be the case?

What size windshield do you have? Do your handlebars/ brake/clutch or any of that hit when you lock out the wheel to either side? Sorry I know this has nothing to do with the intent of the video

Great video I've got the same setup with the slip on mufflers.... And now I'm getting ready to install the same headers.

I was going to watch a few of these videos to get some install tips. No longer necessary, your video was perfect. Gave all i need to know. Thanks

Did you have to use a thinner gasket? I’m trying to get mine done but the stock gaskets aren’t letting my line it up

Great video! I was about to install the P/N 69201599A on my 2018 FLHP, but realized there is no power on the 325b connector. Fuse seems OK (checked with ohmmeter), any ideas?

Exactly what I needed to know. Simple explanation and worked perfectly. Thanks!

Fuckin yuppy calling himself a tech. 😆 🤣 😂

Just ordered mine for my factory 47 bars on my Roadglide. Broke two ram mounts and hopefully this does the trick. Thanks for the information.

I good tip is when removing the bulb (w/cloth to keep hand oil off bulb) is to make note of the orientation of the 1157 bulb pins as you remove them. This way when installing the led lights will make for an easier insert into holder.

Lol.i need help getting it back on now lol I thought I had it

Thanks for the upload, a heel-toe shifter is a must unless you want to mess up your boots ( already starting a small hole in my left shifter boot).👍

This is not right!!! You need to adjust the clutch from inside the derby cover. Twisting the yellow spring does nothing. All that does is put slack in the cable to make the proper adjustment. Stop spreading BS

Perfect video. Just got the hardware for my '22 RK Special 👍🏼

New subscriber. Thanks for this video. I have a dumb question I have a 21 RK I don’t see the empty port. Is this plugged into something else. Per instructions it looks like it should be empty and visible. Can you help?

Did I miss it in the video ? Why did you change them ?

I'd like to get the Harley hammock but the seat is huge! You can land a plane on the passenger seat. I sure wish Harley would get there act together and develop a decent seat where it looks nice on the bike and not ridiculously oversized. It should not be that hard to find a good seat.

CD makes these for Harley, true story

I just need to connect a switched powwer source for my dash cam. The old one I connected to the power port in the tour pack but the new cam system shuts down if I plug just the usb outlet into it. this looks like just what I need. Which wire would I connect from this kit? Thanks

hi...I like the heel toe shifter but I have big feet(size 14 men) so I bought the extended toe shifter which is 3.5 inches longer. I no longer have any problems getting to the heel part, but when my foot is on the board, no part of my foot is under the toe shifter; I have to slide my foot forward to get it under. Do you see that as a problem? Really, the only time I need to shift up with my toe is to find neutral. What do you think??? Thanks!!!

Nice and simple. Great install and thanks for sharing.

i got the specs. just need to get the torque wrench.

whats the factory specs? what torque wrench should i get to do it myself? or is better to pay harley $150.00 dollars!

your way seems simple??