วีดีโอ

Hello, I have ER-TFT043A1-7 LCD screen. I couldn't find sample code for the st7262 driver. I want to run it with Stm32h5 device. Can you help?

Please help me i really like the watch i think you can help me

Hi can you mod Casio CA-53wf-1b it has negative display but doesnt have backlight😢

is this display usable without backlight ? (transflective)

how to wire it with esp32?

because of you, now I know this beaitty song. Thanks

Is this compatible with Arduino uno r4 wifi?

Can you recommend a 7inc touchscreen lcd that is compatible with Arduino uno r4 wifi

Umm you have a low voltage warning⚡... And also, 1st 👆🏻

i have purchased and trying to interface it with pic microcontroller, but it isnt working. could u plz provide me example code with pic or with any other microcontroller.

Podrian compartir el codigo de favor

I want to use it in rpi 3b+ for temp and ip address showing please help me please

incredible video. i am stunned

Is the HDMI board universal for every LCD?

Good day . Could you help me? use Arduino Due and 7" TFT LCD Display SSD1963 Module Touch Screen Shield. I can't read the image from the sd card. I bought your lcd display, I was hoping that the libraries and examples are! Marian PaĽa- Slovakia - PREŠOV.

hey can I use this with arduino giga r1 wifi?

Display controller is similar to ILI9341/GC9A01A

do you have same screen but 3.2" ?

I want to buy this item but my 11 pin is from Indonesia

The UC1609 also works with the i2c interface, but this requires minor modification to the PCB.

can this be used with an i2s adapter module?

can this be used with an i2s adapter module?

Thank you for THIS.... Recording. Regards. Dziękuję za TO.... Nagranie. Pozdrawiam.

Just bought this display. Planning to connect to raspi 4. Unfortunately your docs doesn't match the spi interface labels on the lcd board, which are VCC, GND, DIN, CLK, CS, DC, RST Guessing DIN is SDA and CLK is SCL. Am I right? A python example would be nice. Thx

For a sec I thought he was going to write HELP! on the screen..

I am testing the Circular Progress Bar(DCh) function with my ER-TFT028A2-4-5465 (2.8-inch) screen. When I send data (from UserCommand on UI_Editor), for example I send 0000 000A and then 00 00 0050 and then 0000 0165, everything works fine. The problem is when I send, for example, 0000 0160 and then 0000 000B (a number smaller than the first one sent), the bar stays full and there is no change.​ I hope you can help me with that.

do you think it works on Sharp LQ050T5DW02 is a 5 inch TFT LCD panel with a resolution of 480x272 pixels. ?thanks

Nice little display. Very cool!

Greetings! Only Chinese sources? I am testing its 2.8-inch screen (ER-TFT028A2-4-5465), I followed this same tutorial, but it does not write any text on my screen. I am also using UserCommand to send the data through the UART, I project images (80h), numbers (90/91h) but the text does not work for me.

hello can i connect this to arduino mega without arduino shield ?

Hello, please help and guide me. I have a 9-inch monitor, the model of which is this HSD0901CW1-A00 This monitor has 26 input pins. Now, in your opinion, which control board in the market can I use to run it? My goal is to transfer the av image to the monitor please help

Também preciso do diagrama de conexão para o Esp8266

Do you have micropython driver for this particular display?

Too bad the customer registration area is very poor. On any international supplier's website, you have the option of entering the buyer's documents, and if it's a company, the company's registration, so Fedex can clear customs. I didn't see any of this on Buydisplay; it goes straight to the payment page, which makes it clear: they don't seem to care about the customer. The customer bought it, paid for it, now it's up to them! I'm from Brazil and I wanted to make some purchases for my company

Too bad the customer registration area is very poor. On any international supplier's website, you have the option of entering the buyer's documents, and if it's a company, the company's registration, so Fedex can clear customs. I didn't see any of this on Buydisplay; it goes straight to the payment page, which makes it clear: they don't seem to care about the customer. The customer bought it, paid for it, now it's up to them! I'm from Brazil and I wanted to make some purchases for my company

Too bad the customer registration area is very poor. On any international supplier's website, you have the option of entering the buyer's documents, and if it's a company, the company's registration, so Fedex can clear customs. I didn't see any of this on Buydisplay; it goes straight to the payment page, which makes it clear: they don't seem to care about the customer. The customer bought it, paid for it, now it's up to them! I'm from Brazil and I wanted to make some purchases for my company

Too bad the customer registration area is very poor. On any international supplier's website, you have the option of entering the buyer's documents, and if it's a company, the company's registration, so Fedex can clear customs. I didn't see any of this on Buydisplay; it goes straight to the payment page, which makes it clear: they don't seem to care about the customer. The customer bought it, paid for it, now it's up to them! I'm from Brazil and I wanted to make some purchases for my company

Too bad the customer registration area is very poor. On any international supplier's website, you have the option of entering the buyer's documents, and if it's a company, the company's registration, so Fedex can clear customs. I didn't see any of this on Buydisplay; it goes straight to the payment page, which makes it clear: they don't seem to care about the customer. The customer bought it, paid for it, now it's up to them! I'm from Brazil and I wanted to make some purchases for my company

how do I connect it to the respberry pi?

how do i get the package to come in my company's name. in the registration area there is only the data of the individual (even then you still need the personal documents; which you don't have on the registration page). when it arrives in Brazil DHL does the customs clearance in the name of the person who bought it.

i am angelika bullmann and its a good video

Cool displays, I enjoy using them. What SPI bus speed are you using in this video?

how can i buy this display? i'm from indonesia

Your videos are short but very informative! Best wishes.

Who is the manufacturer of this Display? BuyDisplay is manufacturer or supplier?

​ @buydisplay5727 I bought one SPI / 8080 parallel screen from BuyDisplay. I only see the demo code for Arduino with SPI interface. I want to do Parallel transfer / get data in Arduino. Please can you have a working demo code.

This is awsome. I was searching for the datasheet for NV3030B all over the internet. Here it is. Thanks a lot :)

hey im completely new to the tinkering community and was wondering if you have code that would allow gifs to be displayed on this oled from a raspberry pi A+

nice

Bisa untuk keyboard piano gk