Manny Vega
Manny Vega
  • 28
  • 250 644
2017 Audi Q7 AC not working FIX!!!
Temporary solution to AC compressor not turning on. Common issue: High pressure ac sensor no signal also ambient sensor no signal. Problem fixed by running a wire from the red plug T17b/6 (purple /white) wire inside the car located under the driver side foot rest, to the purple/white wire on the high pressure sensor plug in front of the car.
มุมมอง: 5 349

วีดีโอ

2012-15 Honda civic water pump replacement
มุมมอง 7K9 หลายเดือนก่อน
2014 Honda civic water pump replacement, this procedure applies to 2012 to 2015 Honda civics with the 1.8L engine. #honda #civic #9thgencivic #diy
07-10 Audi Q7 rack and pinion steering replacement.
มุมมอง 4Kปีที่แล้ว
Watch me replace a rack and pinion steering on a 08 Audi Q7 3.6L . Step by step process and detail description of what needs to be done in order to get this part replaced. This also applies to VW Tuareg and Porsche Cayenne of the same years. #Audi #Q7 #rackandpinion #repair
07-15 Audi Q7 wiper motor replacement
มุมมอง 15Kปีที่แล้ว
Watch me replace the wiper motor on my 2008 Audi Q7 3.6l engine. Step by step process and detail size bolts and tools to use. #audi #repair #q7
02-04 Audi A4 engine mounts replacement.
มุมมอง 23K2 ปีที่แล้ว
Engine mounts replacement on B6 Audi A4 ,with v6 engine.
B5 Audi s4 after run coolant pump replacement
มุมมอง 1.6K3 ปีที่แล้ว
2000 Audi s4 after run coolant pump replacement without removing the intake manifold. Watch me replace this part for the first time.
02-04 Audi A4 Body Control Module replacement.
มุมมอง 45K3 ปีที่แล้ว
Body control module replacement BCM on a 2004 Audi A4 . Symptoms of a bad BCM on my car are wipers not working, rear view mirror not working and headlights are always on even when on the off position. Watch me replace and fix these issues. If you want to reprogram your module thi is what you do; on VCDS . Open the VCDS, then go to SELECT, then 09-Cent. Elect. It's going to show your control mod...
Lonely by Manny Vega Solution
มุมมอง 1.3K4 ปีที่แล้ว
Lonely by Manny Vega Solution bachata 2020
Audi S4 Low Oil Pressure Light FIXED!!!
มุมมอง 7K4 ปีที่แล้ว
Red oil lamp warning light fix for 2000 Audi S4. It also applies to Audi A4 and some Volkswagen Passat.
Acura TSX Rack And Pinion Replacement
มุมมอง 47K5 ปีที่แล้ว
2004 Acura TSX rack and pinion steering replacement step by step process.
2008 Audi Q7 fuel filter replacement.
มุมมอง 20K5 ปีที่แล้ว
Fuel filter replacement 07-10 Audi Q7, might also apply to 03-10 Volkswagen Touareg and Porsche Cayanne 03-10.
Audi S4/A4 V6 Oil Pressure Sensor/switch Replacement
มุมมอง 24K6 ปีที่แล้ว
Audi S4/A4 V6 Oil Pressure Sensor/switch Replacement
Manny Vega en vivo este Domingo 31 de julio 2016
มุมมอง 1458 ปีที่แล้ว
Manny Vega en vivo este Domingo 31 de julio 2016
Sangre de mis venas requinto
มุมมอง 9K10 ปีที่แล้ว
Sangre de mis venas requinto
Manny Vega Grupo SOLUTION ensayo
มุมมอง 64011 ปีที่แล้ว
Manny Vega Grupo SOLUTION ensayo
Audi s4 2.7t cam cap seal replacement
มุมมอง 18K11 ปีที่แล้ว
Audi s4 2.7t cam cap seal replacement
Por culpa de tus Padres (SOLUTION) 2012
มุมมอง 4.1K13 ปีที่แล้ว
Por culpa de tus Padres (SOLUTION) 2012
Robertico y el Montro-mujeres en el mundo hay un monton
มุมมอง 30413 ปีที่แล้ว
Robertico y el Montro-mujeres en el mundo hay un monton
Loisaidas Ayer en Requinto
มุมมอง 2.2K14 ปีที่แล้ว
Loisaidas Ayer en Requinto
mi primer bebe video
มุมมอง 1.3K14 ปีที่แล้ว
mi primer bebe video
The king of the Monster Duranguense
มุมมอง 93914 ปีที่แล้ว
The king of the Monster Duranguense
El Alcohol The king of the Monster
มุมมอง 2.2K14 ปีที่แล้ว
El Alcohol The king of the Monster
Quisqueya Grupo Solution
มุมมอง 2.3K15 ปีที่แล้ว
Quisqueya Grupo Solution
GRUPO SOLUTION-TU DUENO
มุมมอง 4.8K17 ปีที่แล้ว
GRUPO SOLUTION-TU DUENO

ความคิดเห็น

  • @NathanVega-v5c
    @NathanVega-v5c 4 วันที่ผ่านมา

    Great music dad

  • @rbailey225
    @rbailey225 10 วันที่ผ่านมา

    How did you remove the plastic cowl cover? I don't want to break mine.

    • @mannysolution
      @mannysolution 10 วันที่ผ่านมา

      @@rbailey225 after you remove the wiper arms the plastic cowl it’s easy to remove

  • @gregrussell4527
    @gregrussell4527 หลายเดือนก่อน

    Please keep making Touareg repair videos Love my 2008 4.2 v8

  • @OBrienFleming
    @OBrienFleming หลายเดือนก่อน

    Take off the subframe mount to remove the whole assembly in one piece.

  • @terrywilliams8735
    @terrywilliams8735 หลายเดือนก่อน

    My Ac not working they told me it could be my compressor I’m thinking it might be my fuses what do you think

    • @mannysolution
      @mannysolution หลายเดือนก่อน

      It could be a fuse, but check all the links on the comments section. People encounter different solutions to these problems.

  • @luizcisneros3690
    @luizcisneros3690 2 หลายเดือนก่อน

    Thanks Manny. I will try this next weekend. Do you have the name or link to the audiworld thread?

    • @mannysolution
      @mannysolution 2 หลายเดือนก่อน

      www.audiworld.com/forums/q7-mkii-discussion-211/c-compressor-wont-come-3043620/page5/

  • @T-programmer
    @T-programmer 2 หลายเดือนก่อน

    th-cam.com/users/shortsA1Wb8EaeQlE?si=1F0cmN8q8s0r1JAT TH-cam does not allow links to the pictures I uploaded, but I did exactly the same process here. The LIN bus cables under that carpet are definitely breaking due to corrosion.

    • @mannysolution
      @mannysolution 2 หลายเดือนก่อน

      Thank you for your input! Did that fix your issue?

    • @T-programmer
      @T-programmer 2 หลายเดือนก่อน

      ​​@@mannysolution there are no error codes left. All sorted. 🎉

    • @mannysolution
      @mannysolution 2 หลายเดือนก่อน

      @@T-programmer thank you for your useful información. I’ll pin the link to the top comments for others to see

  • @T-programmer
    @T-programmer 2 หลายเดือนก่อน

    I add the links but they are automatically deleted by TH-cam?

  • @T-programmer
    @T-programmer 2 หลายเดือนก่อน

    Today these problems are solved! I removed the seat and checked the main wiring harness under the carpet. The 4 LIN bus wires in the wires going from the rear air conditioner were corroded and broken. I reconnected them all and wrapped them tightly with cloth tape to make them stronger. You can take a look at the pictures from the links.

    • @christhompson5725
      @christhompson5725 หลายเดือนก่อน

      Was this the drivers seat or the passenger seat?

  • @DanielVilchez-q6y
    @DanielVilchez-q6y 2 หลายเดือนก่อน

    Y para la q5 2010 no trabaja el compresor

    • @mannysolution
      @mannysolution 2 หลายเดือนก่อน

      No se si tiene el mismo sistema. Por ser diferentes modelos

  • @jesusmata9565
    @jesusmata9565 2 หลายเดือนก่อน

    I replaced it and ita still leaking from the boot😢

    • @mannysolution
      @mannysolution 2 หลายเดือนก่อน

      Was it new or used? Used parts are usually hit or miss.

    • @jesusmata9565
      @jesusmata9565 2 หลายเดือนก่อน

      @@mannysolution new

    • @mannysolution
      @mannysolution 2 หลายเดือนก่อน

      @@jesusmata9565 a new part should not be leaking.

    • @jesusmata9565
      @jesusmata9565 2 หลายเดือนก่อน

      @@mannysolution i know gotta look under good see where the leaks from,

    • @humbledhands
      @humbledhands หลายเดือนก่อน

      Was a bolt loose on that rack? Did you have to replace rack again?

  • @CornerCamTo
    @CornerCamTo 2 หลายเดือนก่อน

    @manny Vega! Quick update bro, one of the fine gentlemen on the Audiworld forums(ggms16) posted a pic recently on where to find the wire for the rear blower, seems easy enough so it'll be my next project.

    • @CornerCamTo
      @CornerCamTo 2 หลายเดือนก่อน

      Rear blower now fixed! Ice cold in the back too, the air sensor I dont really care about. All I had to do was remove the top trim off the back of the center console, remove 2 screws, get behind the AC controls and splice the purple white wire, I did it the lazy way so I ended up connecting to the exposed wire from my last job so I didnt have to reopen the front trim pieces. Worked like a charm!

  • @sandyvargas1998
    @sandyvargas1998 2 หลายเดือนก่อน

    This sounds better !!

  • @robhay23
    @robhay23 2 หลายเดือนก่อน

    Do you know what the letter under the barcode means? I got a N and a placement part has a S

    • @mannysolution
      @mannysolution 2 หลายเดือนก่อน

      According to Audi it’s a variation of the part number or an update on the part.

  • @Bresoto
    @Bresoto 3 หลายเดือนก่อน

    what are the differences 8e0907279 to 8e0907279F? Because i have a A4 B6 1.8T 2002, wipers are not working, and i bought this ONE 8e0907279 and my car currently using 8e0907279F

    • @mannysolution
      @mannysolution 3 หลายเดือนก่อน

      @@Bresoto it’s different years and models. But they can be coded to your car if you have vag-com vcds. On the description of this video I show how you can coded

    • @Bresoto
      @Bresoto 3 หลายเดือนก่อน

      @@mannysolution thanks

  • @jorgefajardo2213
    @jorgefajardo2213 3 หลายเดือนก่อน

    I replaced the thermostat there's no leak or sign of coolant splash ..the pump looks clean and it doesn't make any noise but the coolant doesn't move at all in the radiator the radiator and fluid looks clean too..please any advice?

    • @mannysolution
      @mannysolution 3 หลายเดือนก่อน

      @@jorgefajardo2213 might have a clogged heater core or clogged radiator. Is the car overheating?

    • @jorgefajardo2213
      @jorgefajardo2213 3 หลายเดือนก่อน

      ​@@mannysolutionThank you for answering my questions. The heat message came on my cluster so I turned the heater on full blast and also shut the engine off a couple of times untill I drove it home but no more over heat light after that I hope no damage was done . Tomorrow I'll change the pump and the radiator as the next two steps.

  • @MichaelWaller-s8y
    @MichaelWaller-s8y 3 หลายเดือนก่อน

    Thank you for sharing this video!! Looks doable and I’ll be attempting soon!

  • @maverick_da1735
    @maverick_da1735 3 หลายเดือนก่อน

    Subscribed. My 2018 Q7 3.0 A/C started blowing warm. Checked Freon w/ gauge and pressure even. Compressor clicks on but warm air. …

    • @mannysolution
      @mannysolution 3 หลายเดือนก่อน

      Did you tried the wire bypass to the sensor?

  • @gassan16
    @gassan16 3 หลายเดือนก่อน

    Did you clean the connectors from the ECU? Any updates on getting the rear blowers to work?

    • @mannysolution
      @mannysolution 3 หลายเดือนก่อน

      I haven’t done it yet, been busy with other cars. But video will come soon, I’ll keep you updated

    • @gassan16
      @gassan16 3 หลายเดือนก่อน

      @@mannysolution I'll give it a try on my own q7 tomorrow and report back. I did the wire to the pressure sensor but will also add the ambient sensor tomorrow. I really need the rear blower to work

    • @mannysolution
      @mannysolution 3 หลายเดือนก่อน

      Let me know how it goes.

    • @AhmedBhayat
      @AhmedBhayat 3 หลายเดือนก่อน

      @@gassan16 hey there, any update to this - the bypass worked great, rear blower still showing the same code. :(

    • @gassan16
      @gassan16 3 หลายเดือนก่อน

      @@AhmedBhayat cleaning ECU connections didnt work. I’m sure it’s something inside the cabin. I wired the Pressure sensor and the humidity sensor and those codes are gone, cold AC, but still no rear AC, I looked at the rear ac blower module and it seems to have the same colored cable, so I will soon wire that one to the same spot and see if it works. I believe blower is under center console

  • @mnoll1580
    @mnoll1580 3 หลายเดือนก่อน

    great video! I've got a super weird one though. Why would the turn signals, head lights and wipers not work when the interior lights are dimmed? I have VCDS and I've coded my new BCM/CECM to my S4 and I've used the Adaptation setting to attach the new VIN to the new box and its still not updating. I am completely lost as to why the new box will not attach the VIN. Every scan I keep getting the 01794 "Control Module - Incorrect Chassis (VIN) Number" fault. Anyone else run into this issue??????

    • @mannysolution
      @mannysolution 3 หลายเดือนก่อน

      Check inside the ECU box these cars are known for having water inside the ECU box. There’s some relays in there that sometimes get corrosion by having water inside for long and would cause all kinds of issues.

  • @alirahman4762
    @alirahman4762 3 หลายเดือนก่อน

    You opened the wrong screws of the tensioner. you only had to open the one 12mm screw at the end of the tensioner where the hydraulic spring is. But youve opened the two screws of the bottom casing that was holding the the tensioner. this made removing the tensioner out difficult. Once that one screw at the hydraulic spring was removed, the tensioner would have rotated around the water pump and come out, making your job much easier

    • @mannysolution
      @mannysolution 3 หลายเดือนก่อน

      Thank you for your input, next time I’ll do that 🙏🏼

  • @DjvvhcGgyg
    @DjvvhcGgyg 4 หลายเดือนก่อน

    How much was the part ???

    • @mannysolution
      @mannysolution 4 หลายเดือนก่อน

      I paid around $40 dollars on eBay

    • @DjvvhcGgyg
      @DjvvhcGgyg 4 หลายเดือนก่อน

      @@mannysolution thanks bro I see alot on like for $40 range I called O'Riley and they told me $200+ no mamees lol 🤣 I'ma order it rn I appreciate you bro have a good one padre

    • @mannysolution
      @mannysolution 4 หลายเดือนก่อน

      No problem bro! I’m here to help

  • @DjvvhcGgyg
    @DjvvhcGgyg 4 หลายเดือนก่อน

    This can cause it to hella leak rite bro ? Because it only leaks when iturn on the car or basically when ignition isturned over but itwasbad today ? If the gas tank was cracked wouldn't it leak constantly???

    • @mannysolution
      @mannysolution 4 หลายเดือนก่อน

      Yes this can cause a leak that you can smell as soon as you open your car. Mine was cracked and it looked like someone had try to repair it before. After replacing this filter no problem.

    • @DjvvhcGgyg
      @DjvvhcGgyg 4 หลายเดือนก่อน

      How kuch was the part I've been having this Q7 it's a good family car ​@@mannysolution

  • @ilia95rus
    @ilia95rus 4 หลายเดือนก่อน

    Tu bro! I fix my ac

  • @AED-903
    @AED-903 4 หลายเดือนก่อน

    Thank you bro, This explanation is really good. I also own a 2016 Q7 4M. I have been having problems with AC for 2 days. I am getting the following 3 different errors and I will examine the sockets you explained in the video first thing tomorrow. My DTC Error codes are ; - High pressure sensor, no signal - Outside air quality/air humidity sensor, no signal - Rear fresh air blower control module, no signal.

    • @mannysolution
      @mannysolution 4 หลายเดือนก่อน

      Those are the codes I was having. But after doing this my ac is working except for the rear blowers . I will try to figure out the root of this problem.

    • @AED-903
      @AED-903 4 หลายเดือนก่อน

      ⁠@@mannysolution The AC worked the way you described, which is great! However, as you said, the rear blowers are not working. Did you find anything else about this? I will continue to work on it. By the way, one last thing: Audi service asked me for 30 thousand euros for this problem, can you believe it? 😊

    • @mannysolution
      @mannysolution 4 หลายเดือนก่อน

      ⁠it’s crazy so many people are having this issue. I will get to the bottom of it one day😅. 30 thousand it’s ridiculous, glad you could fix it for less 😂

  • @matthewsuarez7321
    @matthewsuarez7321 4 หลายเดือนก่อน

    Why did u replace it?? Was it making a crunching noise of any type that u could hear from front end and feel in ur floorboard????

    • @mannysolution
      @mannysolution 4 หลายเดือนก่อน

      Mine was just leaking fluid through the boots

  • @renatomanuel2851
    @renatomanuel2851 5 หลายเดือนก่อน

    thanks you, Could someone show me a video of why the central locking system could not work?

  • @lou4nysq510
    @lou4nysq510 5 หลายเดือนก่อน

    I have a sg5 when I push the AC bottom, the AC light do not stay on. Blows hot air.. going nuts this just happened a few hours ago when it was 102 in NJ..

    • @mannysolution
      @mannysolution 5 หลายเดือนก่อน

      In my case the ac light was turning on fine. Maybe you’re low on refrigerant

  • @CornerCamTo
    @CornerCamTo 5 หลายเดือนก่อน

    Hey bro, I've got a couple of quick questions: 1. Where did you route the wiring in the end? Did you create a new hole in the firewall behind the foot cover? 2. I tried removing some of the panels and got the top two off, but the bottom one seems stuck and wont budge at the bottom. Did you have to take off the door sill/foot sill plastic to access it?

    • @mannysolution
      @mannysolution 5 หลายเดือนก่อน

      Honestly I haven’t route it through the car yet because I haven’t had any time. I just route it through the door and the fender for now but most likely will have to make a whole some where, but My goal is to find the short and fix it correctly.

    • @CornerCamTo
      @CornerCamTo 5 หลายเดือนก่อน

      @@mannysolution Fixed it - thanks for the video brother!! I also didn't run the wire properly yet, ran it under the bottom engine covers and then under the door sill. Front AC vents are blowing ICE cold but the rears are not working yet still have that rear blower module code and air quality sensor code. For another day... lol.

    • @mannysolution
      @mannysolution 5 หลายเดือนก่อน

      @@CornerCamTo no problem man! My rear vent are not working either but I’m happy at least I have ac in the front with the hot days we’ve been having lately.

    • @CornerCamTo
      @CornerCamTo 5 หลายเดือนก่อน

      ​@@mannysolution Exactly! just happy its working - what I'll be doing next is running a wire from the High pressure sensor to the Air quality sensor - might fix both codes at once. Based on how many people have talked about this looks like a common point of failure.

    • @AED-903
      @AED-903 4 หลายเดือนก่อน

      @@CornerCamTohi bro, did you know find any way to fix the other sensor issue? Thx

  • @CornerCamTo
    @CornerCamTo 5 หลายเดือนก่อน

    Enjoy that Ice Cold air brother!! :)

    • @mannysolution
      @mannysolution 5 หลายเดือนก่อน

      Yes bro! I’m so happy right now 😄

  • @edilbertoportillo1471
    @edilbertoportillo1471 5 หลายเดือนก่อน

    This is an awesome video! Replaced both ww fluid pumps and they still didn't work. I knew my lights were also turning on as soon as ignition was turned on but never would have thought both problems would be connected to the BCM. I have high hopes that I will be able to fix all these issues on my car! Thanks for the video bro.

  • @CornerCamTo
    @CornerCamTo 5 หลายเดือนก่อน

    What ended up being the fix for your car? I got these 3 codes and I bought the switch thinking it may fix it, I'll be trying your method on installing it over the weekend. 262658 - High-pressure sensor - no signal 263171 - Outside air quality/air humidity sensor no signal 393510 - Rear fresh air blower control module no signal. I believe my car has a shutter can I still access it using this method or would I need to take the bottom engine cover off.

    • @mannysolution
      @mannysolution 5 หลายเดือนก่อน

      I had the same codes but replacing the sensor didn’t fix the issue, my ac still not working.

    • @CornerCamTo
      @CornerCamTo 5 หลายเดือนก่อน

      @@mannysolution ah damn, I found an forum that mentioned it could be a wiring issue from the air quality sensor to the high pressure sensor. I'll try this first, if not might have to drop some money on having a mechanic check it out.

    • @mannysolution
      @mannysolution 5 หลายเดือนก่อน

      Please post any updates on this video hopefully we can figure it out together I want to help others solve this issue

    • @CornerCamTo
      @CornerCamTo 5 หลายเดือนก่อน

      @@mannysolution Yeah for sure! Will do!

    • @CornerCamTo
      @CornerCamTo 5 หลายเดือนก่อน

      ​@@mannysolution Quick update: The new pressure sensor didn't resolve the issue, I also checked the fuses, none were blown. Next, I'll be inspecting the wiring over the next couple of days. If that's not the issue, it might point to a problem with the compressor. I'm really hoping it's not the compressor though. The issue was sudden and random; the error codes timestamp perfectly with the AC failure.

  • @niconite
    @niconite 6 หลายเดือนก่อน

    what was the reason you changed it? I have the exact same suv and mine has a hard time cooling, like compressor wont engage, I usually have to run the suv for a few minutes with the ac system off, then it finally comes on.

    • @mannysolution
      @mannysolution 6 หลายเดือนก่อน

      My problem is the compressor is not turning on. I hooked up the scanner and gave me a high pressure sensor fault, I replaced it but didn’t fix the issue.

    • @niconite
      @niconite 6 หลายเดือนก่อน

      @@mannysolution oh man. These suvs are lovely but when they give problems, omg

  • @gibson3304
    @gibson3304 6 หลายเดือนก่อน

    Dude, thank you for the quick instructional video! This is exactly what I was looking for.

    • @mannysolution
      @mannysolution 6 หลายเดือนก่อน

      Glad it helped!

  • @orie1504
    @orie1504 6 หลายเดือนก่อน

    You are appreciated

  • @rudyhidalgo596
    @rudyhidalgo596 7 หลายเดือนก่อน

    Hola Manuel 😊

  • @pottypotter110
    @pottypotter110 8 หลายเดือนก่อน

    Thats not the fuel filter is it ? Looks like a pump

    • @mannysolution
      @mannysolution 8 หลายเดือนก่อน

      It’s a fuel filter. The electric fuel pump it’s on passenger side, and the other high pressure fuel pump it’s on the engine.

  • @maku8936
    @maku8936 8 หลายเดือนก่อน

    ⭐️⭐️⭐️⭐️⭐️👍

  • @AdrianAlvarez-o6n
    @AdrianAlvarez-o6n 8 หลายเดือนก่อน

    How many miles on the car? Was it overheating? Or just to change it ?

    • @mannysolution
      @mannysolution 8 หลายเดือนก่อน

      The car has 143k and it was overheating. But the reason for overheating was a head gasket failure , it was in an accident and the person drove the car with a cracked radiator warping the cylinder head.

    • @AdrianAlvarez-o6n
      @AdrianAlvarez-o6n 8 หลายเดือนก่อน

      @@mannysolution ok cuz I’m thinking of replacing my timing chain but they say it’s recommended to change the water pump too…

    • @mannysolution
      @mannysolution 8 หลายเดือนก่อน

      Yeah, you might as well replace it because in order to get to the timing chain you have to remove the water pump.

    • @JOP518
      @JOP518 8 หลายเดือนก่อน

      May I ask why would you change the timing chain? What mileage do you have? Thanks…

  • @austinyang6488
    @austinyang6488 9 หลายเดือนก่อน

    Whst was wrong with the old steering rack?

    • @mannysolution
      @mannysolution 9 หลายเดือนก่อน

      It was losing all the power steering fluid and it was coming out of the boot.

  • @moneygrip4464
    @moneygrip4464 9 หลายเดือนก่อน

    Havin a little trouble with the drivers side wiper arm huh??? It took me a while to separate it...

    • @mannysolution
      @mannysolution 9 หลายเดือนก่อน

      Yes it’s a bit hard to remove but it’s doable.

  • @CrappyCSX
    @CrappyCSX 9 หลายเดือนก่อน

    Thank you, great video.

  • @Fadez_Capone
    @Fadez_Capone 9 หลายเดือนก่อน

    I’m getting ready to replace my rack and pinion is my 2007 , when you put the new one in did you have to take that top part that feeds to the inside of the car when you put the new one in?

    • @mannysolution
      @mannysolution 9 หลายเดือนก่อน

      Yes I removed the top part of the rack and pinion in order to slide it out of the driver side of the car. You can also get an inch or 2 if you loosen the subframe a little bit but not remove the subframe bolts completely, just enough to get more wiggle room.

  • @OG-bh2rb
    @OG-bh2rb 9 หลายเดือนก่อน

    any idea if this is the same for the 1.8t engines

    • @mannysolution
      @mannysolution 9 หลายเดือนก่อน

      To my knowledge they have the same mount location , so same procedure and more space for you since you have the 1.8t engine.

  • @ilkinaz1961
    @ilkinaz1961 10 หลายเดือนก่อน

    Perfect explanation!) u are the best) best video ever to change Engine Mount by audi a4 b6/ b7 or Seat Exeo) VW PAssat and Skoda Superb same way)

    • @mannysolution
      @mannysolution 10 หลายเดือนก่อน

      Thank you,I’m glad I could help.

  • @mariusolarson9368
    @mariusolarson9368 10 หลายเดือนก่อน

    Thanks Manny for your informative video. I also have a few electrical symptoms in my B6, like ac flaps are constantly moving after the car is turned off, dipped headlight error all the time as well as the light switch that does not turn off the headlights. Do you think the dipped headlight error is coming from a faulty BCM?

    • @mannysolution
      @mannysolution 10 หลายเดือนก่อน

      Most of the electrical problems this car’s have comes from water getting into the BCM and CCM. The headlight switch and headlights are controlled by the BCM the part I replaced, but you should also check under the carpet (driver side) for water under there. And also under the hood where the ECU lives. Let me know if it helps.

  • @douglasmeireles3027
    @douglasmeireles3027 10 หลายเดือนก่อน

    Esse módulo também é do ar condicionado?

  • @eg39701
    @eg39701 10 หลายเดือนก่อน

    Whatever knuckle brained IDIOT replaced the engine mounts on my car last put RED LOCTITE on the bolt and tightened it down to 1000000 ft lbs. I'm literally going insane trying to remove this mount, because there's barely any room and any wrench I use on it just slips off. I was thinking of maybe taking an oil filter wrench and grabbing the mount and trying to twist it off. I've blasted the bolt with fire, WD-40, Acetone, and PB Blaster and no matter what I do I can't get this damn bolt off. Also, very good video. No hate :)

  • @mannysolution
    @mannysolution 10 หลายเดือนก่อน

    Check if your rack and pinion boots are greasy. If they are,That’s a sign of a bad rack and pinion.

  • @hamoodajmi3150
    @hamoodajmi3150 10 หลายเดือนก่อน

    I own a porsche cayenne and i have a strong whining noise only when turning the steering wheel right. is this a sign that the steering rack is failing? Or could it be the power steering pump?