วีดีโอ

Brilliant, £4.75 on Amazon, thank you 🙏 👍🏻

Boiler lights then goes out

Helped greatly. I'd had the funny flashing box (top left corner; bottom right corner) with a 94 number apparently inside it. Didn't appear to match any fault code nor was the flashing 'box' in the manual, so a bit stumped. Your video was clean and clear on getting the tru old code. Had to watch your finger for the final 'get back to normal' step 😅. All good.

Great information thanks

+++

How do you unravel the clips on top of heat exchanger. I really struggle

How do you unlock this valve

Nice one 👍🏼

It’s a great feeling when you’ve done all that and the fan pressure test is worse than before you fucking started, new heat exchanger here we come.

how do you change selector knob if broken

Legend, you’ve just saved me a fortune. After 3 weeks of no hot water I replaced pcb (thankfully a cheap eBay second) and still failed. Put on my big girl pants to have a go myself in the depths of the scary boiler beast and Venturi was completely blocked. Quick cocktail stick and pipe cleaning and now fires again, better than before. Very grateful you enabled me to fix myself with zero boiler knowledge. Thank you!

Do you have an annual service video for the Baxi neta-tec combi 33ga, Thanks

Will the fga not pick up that Co around the site glass ?

my manual air vent is leaking water continuously, any ideas why? Gonna call the plumber tomorrow

Thanks mate, explained in detail, very helpful

for those whose tubine is stuck solid. 1. remove pump (2 screws). That will give you space. 2. Use 18 mm six sided socket (from toolstation). standard 18 mm 12 sided will slip. 3. get a breaker bar, or extended rachet. (spray some wd40 on flow turbine) you should be able to get off.

could be a better video

That's a proper service there, cheap engineer just checking operation and clean trap

We had groaning noise each time boiler fired up, which has now disappeared after engineer from Ideal replaced burner because we weren't getting any hot water.

Thank you so much, worked a treat. 🎉

Got red and green lights flashing, changed the PCB but still the same cant reset?

good vid mate , ive recently qualified so this sort of content is well handy

This video gave 0 information regarding the noise cure

Great videos mate, they are a great help.

Once a took it out service mode just getting message c-On and number you know why

Thanks for sharing. I’ve got a Baxi Platinum and an 18mm socket fits well but the whole cartridge is seized in the manifold…..I’ve tried a lot of force but it’s not moving. Any tips? Thanks.

I turned the square plastic bearing block round on the back of the machine but the scraping noise is still present as if the front of the drum is rubbing on metal, but further investigation shows there is a felt lining between the front rim of the drum and the plastic door housing, looks like I will have to buy a new one 😢 thanks for video anyway 👍

Great support,thank you for uploading videos

Do you have to replace the gaskets when you talk fan off and main heat exchanger off

Hi, I have an ariston e combi evo. Do you know if a smart thermostat would be compatible with it, and which one? At the moment we have no thermostat and can only control the heating through on/off on the boiler. Thanks

Just has our boiler serviced by heatforce who fitted the boiler 3 years ago and they didnt do half of what you did when they serviced it as i was there the whole time, it has a TF1 Sigma filter should he cleaned this as he didnt do anything we paid a lot for the service and he didnt seem to do much for the ammount we paid

Amazing 👍

Great tips 👍

Another great video fella. Not sure how i missed it previously..

Terrible video !

Entering the engineer mode when setting the output is this the percentage output or the temperature. I want to use this for balancing so as to have a constant output. Modulation is great not just when you are trying to set a drop which keeps changing.

Hi, i have ariston combi clas evo he boiler , when i try on test mode change from heating to hot water and open hot water pipe nothing happened , heating working perfect, but no hot water😢

Didn't work for me as previous person used loctite couldn't even undo it with grips

203 code ?

many thanks for your video, it's the only one I found that actually explains draining the boiler, and not the whole system. Need a little help from you or anyone else that can help me with this query. The screws that you turned to stop the hot and cold water flow has imbedded screws. Do I need to loosen the inner screw before shutting of the flow to the taps? I need to replace the heat exchanger.

Suprima 100L Same problem get spark but no start up. Checked the venturi valve as video but the 100L looks nothing like yours. Only 1 cm long within fan and opening full dia size 3mm. Is that correct?

😊

My Alpha cd32 burner was only firing for 50 seconds before switching off every 4 minutes. Radiators are all hot. The burner short cycles even when warming the system from cold. The upper pcb dial is turned to full burn. Is this dial used to enter service mode or to safely turn down the burner and reduce cycling on and off?

My boiler keep displaying 0 and won't come on with water or heattint

I have a six year old Alpha intec boiler and it has broken down with the same thing once a year, every year since installation. The diverter valve goes. Is this a problem on all Alphas? I could do with knowing how to change one when the warranty runs out.

This worked for me! So a big thank you for making this video has this has saved me from having no hot water or central heating over Christmas. 👍

What happens if you have an e10 error you've added water pressure to the green area to about 1 and boiler still doesn't kick in

Great video! Thanks 🙏

Have a green star 30 cdi. All the lights are flickering. What could be the fault? Thanks

Hello, I have a Vibe 25a gas stove. I have a problem with turning on the stove.The furnace has a problem with starting. When I hit the integrated circuit board, the furnace starts.The question is which relay is responsible for starting the furnace.