วีดีโอ

@@cameronchivers7436 interesting that you mention electric. I used an electric shrink wrap gun many years ago when I worked for a company that rebuilt diesel engines. After rebuilt the engines were painted and wrapped. That was my first exposure to shrink wrap. Yes, it had better control and was easier to use. It also had a very thick cord, I am assuming 240V if not 550V, it definitely used a lot of power. I looked into electric for my DIY shrink wrapping, they are very expensive, not pragmatic for my uses. Meanwhile, I have used a regular 120V heat gun to wrap small parts, it worked but was very slow.

@@johnbannister501 There was a brief scene when the board was supported by sawhorse brackets on one end only. That was just during set up; both ends were supported by sawhorse brackets before shrink wrap. Thanks for watching and for the comment.

Dude, did you watch the video at all? I explained which plastic and where to buy it within the first minute of the video.

Vents are always a good idea but not always necessary. Dry boats don’t need vents. If you park your boat on the water all season you should definitely use vents.

He was one of a kind, the greatest. RIP Oscar Wellington

Maybe, depends on which type of vent. The area around the hole may also be overheated and thin. It might be too weak to support the type of vent that pokes into the shrink wrap. If you have the type of vent that gets taped in place after you cut a hole it will work.

Patience my friend! I am not even working in that area of the hull yet. keep following, there will more videos for this project posted at a later date. Future videos include improvements to the aft end; including a bilge pump, substantial reinforcement to the transom and possibly a splash well delete (to make room for rear fuel tank). Power will ether be Merc 200 XRI (same wight as the XR6) or a Yamaha Pro-v 200 The format of future videos will change from time-lapse to video with commentary. Thanks for watching.

I don’t think these boats are crap, Grew boats have a good reputation and are actually well built IMO. The previous owner left the boat on the water, with leaky mooring covers, every summer. It rarely got used and then was pulled out in the fall and shrink wrapped; never getting an opportunity to dry out. Under those conditions the plywood cores didn’t stand a chance. They absorbed moisture from the fiberglass and floatation foam then rotted out. Fiberglass, gel coat and floatation foam are all moisture permeable and will absorb water. In extreme cases a fiberglass hull can absorb 10% of is weight in water. Any production boat would rot under those conditions. Once the flotation foam in a boat becomes water logged it is very hard (impossible) to dry it out and the rotting process accelerates. The high moisture content of the fiberglass and foam also created an environment ideal for rot and mold growth when shrink wrapped. In my experience boats that are covered well, and stored on trailers when not in use, tend to rot much less. Yes, I agree, voice over is much needed. Unfortunately, I don’t think the video quality is worthy of the time and effort that would take. I plan to make more boat restoration videos in the future. I have plenty of better quality footage waiting to be edited. I just need to find time to do it. My future videos will include sound, narration and less time lapse. Thanks for watching.

@@faykos9267 thanks so much for the explanation on how this happens. I am a boat owner and want to avoid. Good to know grew boats are ok too. But not often seen out my way.

@@jayk5549 Grew was a Canadian company based out of Penatanguishine, Ontario. They were also known as Cutter. I believe they also made some boats under licence for Chris Craft (Stinger 210, 230, 260 and etc). The company has a very interesting back story full of controversy and misfortune. Check it out online.

Good point, yes tall frames are good insurance against shrink wrap failure, regardless of what material is used. I still use tall frames on other boat warps. When I first started wrapping with vapour barrier I was using very tall frames. I wasn't sure how strong the vapour barrier was, or how well it would hold up. I wanted to be sure it wouldn't break under snow load. I never had an issue. So, over the years I started cutting the frames shorter. Also, the slope you see is not the final slope; I park this boat with the bow high, which increases the angle. Last season here in ON. Canada we had a heavier than usual snowfall. I did not clear it off the boat at all because I wanted to see if it would fail, it did not. Despite having a few feet of very heavy snow piled on it the wrap was fine. I will be restoring this boat someday and I am not concerned about it's current condition. So it was a good boat to use as a sort of test for the wrap. This video was filmed a long time ago, this wrap is going on it's 3rd season now and still hasn't failed. BTW I watch your videos and liked the one on 2.5L oil injection delete.

Are you Facebook? If so, I invite you to join the group Mercury 2.4L, 2.5L Owners. If you don't get accepted it's because I didn't recognize you on FB. I am very selective, so if that happens just Message me on FB and I will accept you.

@@faykos9267 Awesome, I'm gonna try a short frame on a boat that will sit for at least a year or 2 with regular wrap just to see. No facebook, this is my first attempt at social media, might have to make some more vids about old outboards or maybe not? Seems they're meant to be secretive like don't tell anyone how to manipulate the ec on an efi or make it easy to work on the carb motors.

Yes, it is a challenge to seal around the transom. There is usually openings on each side of the outboard where air can get in/out. If you keep your boat on the water during the boating season it's a good idea to add vents when shrink wrapping. Fibreglass is permeable so boat hulls can absorb and hold moisture. That moisture can be released from the hull during the storage season and create humidity, causing mold . My boats are kept on trailers when not in use, their hulls are dry so I don't need to use vents. I have been wrapping multiple boats/Sea-doos for more than a decade without vents and never had mold (because my boats are dry, kept on trailers). I highly recommend that you use vents especially if your boat stays on the water when not in use. Even if you keep your boat on a trailer it is good insurance.

True, and good advice. Useful on bigger boats with a high freeboard. I had a section of the video where I talked about preheating and post-heating. Unfortunately the video was getting too long and that part got cut. That advice should also come with a caution; you have to be conscious of the amount of preheat and adjust for it as you get higher up the wrap or else you could burn through.

Seems to shrink the same, did you actually watch the video? It’s drum tight, just like shrink wrap. In regards to UV, read the description. If you have proof of these UV additives please share. Otherwise you are just making an assumption that they exist. Consumers need to be less naive and trusting of marketing and branding these days. There’s a good chance you are correct, there’s also a good chance there’s no difference except color and the writing on the label. Without access to trade secrets we have no way of knowing which additives are added, if any. All we have to rely on is experimentation. I have experience: I have a 04 Sea-doo GTX, it’s a fibreglass hull, viper red gel-coat. It’s been wrapped with vapour barrier every season since 2010… it’s never been buffed and it’s still bright red. Red gel-coat is highly susceptible to fade due to UV, yet my red Sea-doo has not faded at all. So, my experience indicates that there must be some UV protection in vapour barrier. Advantages are cost, availability and convenience. Vapor barrier is 1/3 the cost of shrink wrap, by the time shipping is added the shrink wrap can be up to 4 times more expensive. Shrink wrap is not readily available to people in remote communities. Shipping may take weeks and the cost may make it unaffordable. Vapor barrier is available everywhere as it’s a very common building material. It’s really convenient to stop at a Home Depot vs waiting at home all day for a shrink wrap delivery.

It’s a fact, do the research if you don’t believe me. Got my roll of shrink wrap from Home Depot just ship to store $200 after tax no shipping snd enough for 4 years for my 18’ boat. To each their own but I would buy true 7mil shrink wrap. I am surprised it shrunk pretty well but true wrap would also shrink better due to the additives. I did watch the entire video and yes end result looks good to keep it dry👍

Not sure where you live. I am in Canada. They don’t sell shrink wrap at Home Depot in Canada. Most people in my area buy from U-line, my shipping cost from them is $127.00. I can buy a 2000 sq.ft roll of vapor barrier cheaper that! I am in the same city as U-Line. That shipping cost could double if I was outside of the city. So, let me get this straight; you are saying that you researched on the internet and found websites that list the additives in shrink wrap that are not found in vapor barrier. Please share. I am very curious where you found that information. Otherwise I call BS. I don’t think that information is readily available. Theres no doubt these additives exist in marketing and branding but I doubt they are tangible. If you have that information share it, prove me wrong.

Thanks for the video. I am in Alaska, these videos offer great options for us. Yes, if you lived in continental USA you will likely have many options. Amazon and Home Depot will only ship to Alaska for outrageous costs, thus defeating point of DIY

I manufacture shrink wrap for two of the biggest suppliers..... that said vapor barrier will do the job just the same! Thanks for sharing! Us boaters get shafted enough because people think because we have boats we have money. ​@faykos9267

Thanks and yes, GoPro 360. Edited with Quick, iMovie and Telemetry Overlay (for the gauge and map).

@@faykos9267 Best in boat video I've watched! Thanks for the info!

Thanks for watching. Cheers

I agree, but not all boats need vents. If the boat was left on the water, tied to a dock all season moisture will permeate into the fiberglass. That moisture can later come out of the fiberglass during storage. I have seen that cause black mold many times. If the boat was kept covered on a trailer when not in use it s hull will be dry and not holding moisture, in that case no vents are needed. Nonetheless vents are a good idea and a precaution worth taking. I should have mentioned them in the video My boats are kept on trailers when not in use; no moisture, no vents, no mold.

I absolutely agree with venting and then venting some more and also using a couple three desiccant containers inside.

@@edwardkawecki8101 Absolutely, it can't hurt to add some vents. I recommend adding vents, especially if your boat is kept on the water when not in use. Even if kept on a trailer it can't hurt to add ventilation. When I started wrapping my boats more than ten years ago, I didn't use vents, not sure why. Maybe I just didn't have any. Then I discovered I don't need them and I haven't bothered with them since. I wrap 2 Seadoo and about 4 boats every season. Been doing that for at least a decade or more. So, That is 60 wraps that I have done without vents and never had mold issues. If the boat is dry and not holding water in the hull when wrapped, then moisture will not increase beyond moisture levels outside. No moisture, no need for vents.

Any problem using the black 6mil for more UV protection?

It's just an old pond pump that I had laying around, not sure where I got it (check Amazon). A bilge pump will work just as good.

Thanks for the head up. The original links expired. I updated with new links and current prices.

@@faykos9267 thanks!!

I haven't tried it but I think you could trail a wrapped boat, it shouldn't be a problem.

yes you can trailer with shrink wrap on if properly wrapped most all new boats are shipped with shrink wrap on if going by Highway for a long distance.

I have been using 6 mil vapor barrier (super 6 by ever built) to wrap at least two Seadoo and four boats for ten years now. Yes it shrinks.

www.powerflexusa.com/shop/category/bmw-x-series-e53-x5-1999-2006-1816