วีดีโอ

My machine is slightly different. My machine does not have a cold button, model number WTW7500GC0, any idea how to put this in service mode? Appreciate any responses!

Amazing 👏 thank you so much

I have a kenmore model 111.75405120 I can find the fan motor for this unit. Do you know if they make a replacement for it fan number is DREP9020LJ and DREP9020LL

The thermal fuse button part is called what? You said it had a couple names. Would you tell me the part number for it. I pressed that button and my LG heated up but you said to replace it so I will. Thank is for your kindness and this vid.

Great video. I guess my model is probably newer as in the never ending quest to make things cheaper, mine only has 5 wheels.

Thanks for your very informative video! Water has been collecting in our fridge for weeks, but we easily fixed the problem in just over an hour following your instructions (and using a hair dryer instead of steam gun). So glad you posted this video.

THANK YOU! I actually liked doing the whole process for knowledge and it worked perfectly 😊 Feels great to be a handy gal!

THANK You! We have a GE GNE29GSHCSS fridge, and the GE website is showing Part #WR60X20880 was the original part, but has since then been superseded by Part #WR60X35205. Now this is where it gets complicated...the fan that's currently in the fridge is a #WR60X10356. I assume that replacing the fan with the 10356 would do the trick and we should assume that no software update is needed?

Is that a gas dryer you're working on? I have the electric version. The reason I ask is because the part number is different that what is on the video.

Very helpful - Any concerns about the foil causing a spark or fire?

Ok this is a very informative video but my one question is can I test anything without taking the entire thing apart

I wish you would have gone into detail and explained why this works, why it broke in the first place, and I'm curious how you became aware of this fix? Thanks!!

Followed to a t problem fixed thanks!

Very well done and informative video on disassembly. Thank you.

Washer enters rinse mode. Completes rinse and Drains. Briefly enters spin mode and then returns back into rinse mode. Help!

Mine blinks Sense&Lid then Done. Can someone help me figure out the code for this

Thank you so much for your post. I was ready to buy an new motherboard, and found this video from Reddit that suggested to search for the Reynolds Wrap fix! I did not need to unwire the harness, but did pull it out so I can get the tin foil wrapped around it.

Helpful video. Audio sounded a little artificial to me.

Hello! I get 5.15 to 5.20 DC Volts from my first reading. From the other cable I get 120v. The fridge and freezer are 25° and 41° respectively. I cleaned the condenser this morning but temperatures still the same. What could it be?

The solnoids go out due to hard water. $22 off of amazon same thing as the one in the description. W11220230 W11096268 Washer Water Inlet Valve by PANDEELS- Fit for Ken-more, May-tag Whirl-pool Washing Machine - Replaces W10632527, W10758829, W10853296, 4591408, AP6329544, PS12349461

Hi. I got f5 e1?

Is the LG front loader 8kg door switch the same with every other LG front loader?

Thank you very much for the video!

Do I need to replace the panel if it’s not damaged?

Great video. My kids broke the ice dispenser door but I’m not sure how to remove the front panel so I can replace the arm of the ice door. Any idea?

Great video. Question. Is the goal of the foil to creat constant contact between the spring and the inside of the touch board, or just to use a thin layer to amplify the signal when my finger hot the power button? Thanks.

Mine doesn't leak or make any ice. The tray is simply empty and the Fridge Manager says the Ice is Full. I think it would start making ice again if it didn't think it was full.

We have the exact same fridge. About a week ago we defrosted the fridge and restarted it, shortly after the freezer didn’t freeze food. Today we did a reset on the control panel and a couple of hours later the fridge was 24 degrees celsius warm. We’re getting a Samsung technician here in a few days.

Worked on my WT7305CW. Awesome! Thanks for sharing. I'll keep extra foil on hand.

Hello. My dryer is glowing, and then *clicks* but no flame. Is this a solenoid and igniter issue? Or a gas valve issue?

Hi buddy, thanks for your video. I have an LG DLEX3700V dryer that's giving me the error code TE1. I looked it up online and found that it might be a bad thermistor. I ordered a new one (model 6323EL2001B) and replaced it. I measured the resistance of the old one, which was about 8K ohms, and the new one reads around 10.8K ohms. From what I found online, the normal range should be around 11K ohms, so I think the new thermistor is fine. I also tested the round thermal fuse you mentioned in your video, and it reads 0.04 ohms, which seems normal. I took apart the vent and cleaned everything, inside and out. There’s no dust or blockage near the two sensors. After reassembling everything, I double-checked all the connections to make sure they're tight. I also measured the resistance at the yellow and blue wires leading into the control board, and it shows around 10K ohms, which means the connection to the board should be fine. Once I put everything back together, I reset the dryer by holding the start button for five seconds while it was unplugged. But when I powered it back on, it ran for a few seconds and then showed the TE1 error again. I tried restarting it a few times, but the TE1 error keeps coming up. Do you think this could be a control board issue? The board is pretty expensive, so I don’t want to buy one without being sure. Could you help me figure out how to use a multimeter to test the board and what kind of readings I should be looking for to determine if the board is bad? Thanks for your time, and I really appreciate any help you can offer!

This was my exact problem. Thank you for creating a concise and clear video on a solution.

Thank you! I was able to do this with my 17 year old son, and it worked.

Even if you adjust your washer, like push it so it's not to close to your wall or dryer or whatever. Anytime the washer is moved, adjusted, repaired, it needs to be calibrated

Thanks for this. I had to get a dead mouse out of mine and this helped me find it.

Thank you! I have the same model and I have been searching for many days on how to open the panels of this model to replace the rollers, belt and Idler pulley I am glad that I found this video.Thank you so much!

My cabrio looks like it’s an older model. Are the parts the same?

Thank you so much! I didn't find any other video that solved my problem. Saved a bunch of money doing it myself.

Make more like this

Works like a charm thanks washer is back to 100%

This video was the first I looked at. It described the problem perfectly. The repair video was perfect every step of the way. The evaporator hose was completely clogged. Once it was removed and flushed into the sink, all was back in good working order. I used a hairdryer to get rid of the ice buildup as I don’t have a steamer. It probably took a bit longer, but no real difference I imagine.

Great video! Thanks!

Do you have a suggestion on the settings for the harvest temperature code and the ice room code to help keep it from freezing up but harvests ice at a decent rate?

Excellent video - love how you actually waited for the sounds. I have the french door version of this fridge and have a similar sound, but its slower and makes 2 cycles - tick tock...tick tock (vs what you have here - tick tock tick tock tick tock rather quick). I thought the same thing that a solenoid was making 2 attempts to do whatever it was trying to do and then stopped. It's really random when it happens, but the noise cycles are always the same. We were having issues with the defrost, but replacing the harness that wires the heater coil. Have you ever heard that type of noise?

Wow, first rate editing and filming. Subscribed!

I have model ZISB480DRC with same display as your video shows. However, pressing and holding all 4 does not start diagnostics. Any ideas? I really need to run diagnostics to find problem. Fridge freezes up sometimes. Caused water bladder to crack and leak.

This saved me. Thank you!

Outstanding video....thank you so much!!

I’ve got a GE fridge with a WR55X11029 inverter. Compressor not kicking on. From everything i read and see, the control voltage input should be between 4-6VDC. Im getting an input of around 14vdc. Im assuming a motherboard problem but was curious to know if it should still run at 14v, and perhaps its the compressor. Ive already replaced the inverter with no change and i checked the compressor windings. The windings were a little high… 16 ohms rather than 6.5 ohms, but all three posts read the same What do you think could be the problem. By the way, this defect occurred after our recent hurricane and it was being run for several days off of a generator

Nice video! Is it normal for the solenoid to make that clicking sound after power up? Seems like it was clicking several times at the very beginning but also clicking after you changed it. Thanks