- 27
- 87 439
Civil 3D
เข้าร่วมเมื่อ 21 ก.พ. 2013
Autocad Civil 3D - Diş Kazısı - Step Excavation (Multiple Bench Excavation)
Contact for assembly: civil3d.designer1@gmail.com
Linkedin Account:
www.linkedin.com/in/civil-3d-designer-76a248299/
*Diş kazısı tip kesit ile 25 adede kadar diş kazısı oluşturulmaktadır.
OPERATION STEPS IN THE VIDEO
Objective: A new road project with a total width of 30 meters will be drawn on an existing road that is 10 meters wide. Step excavation will be applied in sections with significant ground slope in the fill, and its volume will be calculated.
*The alignment, profile, and the assembly of the road have been previously drawn.
1. A corridor and datum surface for the new road will be formed.
2. Step excavation will be applied on the existing surface. A different corridor will be created for the step excavation, and the step width will be set to 3 meters.
*A surface or feature line created from the corridor cannot be targeted for the parts of assembly that form the same corridor. That’s why a different corridor is created for step excavation.
3. The datum surface will be targeted, so step excavation will not be applied on the datum surface above this surface.
4. Step excavation will not be applied in areas where the ground slope is less than 20%.
5. Step excavation will not be performed on the existing road. To ensure this, the boundary lines of the existing road will be targeted so that the step excavation starts from these boundaries.
6. Step excavation will be performed up to the slope edge of the new road. The slope edges will be targeted for this purpose.
7. The final step width will be extended up to the slope edge.
8. A stripping excavation of 1 meter in height will be created, and then step excavation will be applied to the stripping surface.
9. The volume of the step excavation will be calculated.
10. Application points for the step excavation will be generated.
#autodesk #autocad #civil3d #autocadcivil3d #surveying #survey #landsurveyor #engineering #road #roadconstruction #roaddesign #civilengineering #subassemblycomposer #stepexcavation #step #excavation
Linkedin Account:
www.linkedin.com/in/civil-3d-designer-76a248299/
*Diş kazısı tip kesit ile 25 adede kadar diş kazısı oluşturulmaktadır.
OPERATION STEPS IN THE VIDEO
Objective: A new road project with a total width of 30 meters will be drawn on an existing road that is 10 meters wide. Step excavation will be applied in sections with significant ground slope in the fill, and its volume will be calculated.
*The alignment, profile, and the assembly of the road have been previously drawn.
1. A corridor and datum surface for the new road will be formed.
2. Step excavation will be applied on the existing surface. A different corridor will be created for the step excavation, and the step width will be set to 3 meters.
*A surface or feature line created from the corridor cannot be targeted for the parts of assembly that form the same corridor. That’s why a different corridor is created for step excavation.
3. The datum surface will be targeted, so step excavation will not be applied on the datum surface above this surface.
4. Step excavation will not be applied in areas where the ground slope is less than 20%.
5. Step excavation will not be performed on the existing road. To ensure this, the boundary lines of the existing road will be targeted so that the step excavation starts from these boundaries.
6. Step excavation will be performed up to the slope edge of the new road. The slope edges will be targeted for this purpose.
7. The final step width will be extended up to the slope edge.
8. A stripping excavation of 1 meter in height will be created, and then step excavation will be applied to the stripping surface.
9. The volume of the step excavation will be calculated.
10. Application points for the step excavation will be generated.
#autodesk #autocad #civil3d #autocadcivil3d #surveying #survey #landsurveyor #engineering #road #roadconstruction #roaddesign #civilengineering #subassemblycomposer #stepexcavation #step #excavation
มุมมอง: 1 175
วีดีโอ
Autocad Civil 3D - Betonarme İksa Duvarı (Yarmada) - Concrete Shoring Wall (Cut)
มุมมอง 9982 หลายเดือนก่อน
Create concrete shoring wall with assembly and its calculation Tip kesit ile betonarme iksa duvarı çizimi ve hesaplarının yapılması Contact for assembly: civil3d.designer1@gmail.com Linkedin Account: www.linkedin.com/in/civil-3d-designer-76a248299/ *Genellikle yarmada ve dolguda kullanılan betonarme duvarlar için “İstinat Duvarı” ifadesi kullanılsada, bu videoda duvara ait tip kesitin yarmada k...
Autocad Civil 3D - Betonarme İstinat Duvarı (Dolguda) - Concrete Retaining Wall (Fill)
มุมมอง 1.5K3 หลายเดือนก่อน
Create concrete retaining wall with assembly and its calculation Tip kesit ile betonarme istinat duvarı çizimi ve hesaplarının yapılması Contact for assembly: civil3d.designer1@gmail.com Linkedin Account: www.linkedin.com/in/civil-3d-designer-76a248299/ OPERATION STEPS IN THE VIDEO Purpose: A reinforced concrete retaining wall will be added to a filled section of a road project, and calculation...
Autocad Civil 3D - Multi Cell Box Culvert and Backfill -Çok Gözlü Kutu Menfez ve Geri Dolgu - Part 2
มุมมอง 1.9K5 หลายเดือนก่อน
Multi Cell Box Culvert (Create multi cell box culvert with assembly and its calculation) Çok Gözlü Kutu Menfez (Tip kesit ile çok gözlü kutu menfez çizimi ve hesaplarının yapılması) Contact for assembly: civil3d.designer1@gmail.com Multi Cell Box Culvert Part 1: th-cam.com/video/er-zgl9plt4/w-d-xo.htmlsi=OtJN3SMO8QNTnmUA *Skewed box culvert is not drawn with multi cell box culvert assembly. *Ço...
Autocad Civil 3D - Multi Cell Box Culvert and Backfill -Çok Gözlü Kutu Menfez ve Geri Dolgu - Part 1
มุมมอง 3K5 หลายเดือนก่อน
Multi Cell Box Culvert (Create multi cell box culvert with assembly and its calculation) Çok Gözlü Kutu Menfez (Tip kesit ile çok gözlü kutu menfez çizimi ve hesaplarının yapılması) Contact for assembly: civil3d.designer1@gmail.com Multi Cell Box Culvert Part 2: th-cam.com/video/TudX1v4f4T4/w-d-xo.htmlsi=D-M5dfxUQdkSOLyo Box Culvert (Kutu Menfez): th-cam.com/video/RJidLoU1_bs/w-d-xo.htmlsi=E_0_...
Autocad Civil 3D - Hacim Hesabında “Average End Area” ve “Prismoidal” Yöntemleri
มุมมอง 1.1K7 หลายเดือนก่อน
“Average End Area” and “Prismoidal” Methods in Volume Calculation Contact: civil3d.designer1@gmail.com
Autocad Civil 3D - Skewed Box Culvert - Verevli Kutu Menfez
มุมมอง 8K10 หลายเดือนก่อน
Create skewed box culvert with assembly and its calculation. Tip kesit ile verevli kutu menfez çizimi ve hesaplarının yapılması. Contact for assembly: civil3d.designer1@gmail.com *It was not possible to create a 3D Solid model properly in the transition areas of the skewed box culvert corridor, so this process was not performed in the video. *Verevli menfez koridorunun geçiş bölgelerinde düzgün...
Autocad Civil 3D - Pipe Culvert - Boru (Büz) Menfez
มุมมอง 4.4K11 หลายเดือนก่อน
Create pipe culvert with assembly and its calculation. Tip kesit ile boru (büz) menfez çizimi ve hesaplarının yapılması. Contact for assembly: civil3d.designer1@gmail.com *Skewed culvert is not drawn with pipe culvert assembly. *Boru (büz) menfez tip kesiti ile verevli menfezler çizilememektedir. OPERATIONAL STEPS Objective: To draw a pipe culvert project for a road project and perform the calc...
Autocad Civil 3D - Enkesitlerde Kot Etiketlerinin Üretilmesi
มุมมอง 1.3Kปีที่แล้ว
Producing Elevation Label for Cross Section Contact: civil3d.designer1@gmail.com
Autocad Civil 3D - Farklı Eğim ve Yükseklikteki Şevlerin Arasında Lineer Geçiş Şevleri Oluşturmak
มุมมอง 2.1Kปีที่แล้ว
Linear Transition Slope Among Slopes with Different Gradient and Elevation Contact for assembly: civil3d.designer1@gmail.com OPERATIONAL STEPS Objective: A linear transition corridor will be created and calculations will be performed between corridor models with different slope inclinations and heights. The application will be carried out in a project where all sections are cut, and the same as...
Autocad Civil 3D - Farklı Eğim ve Yüksekliklerde Palye Hendekli Şevlerin Oluşturulması
มุมมอง 1.7Kปีที่แล้ว
Bench Ditch with Different Slope and Height Contact for assembly: civil3d.designer1@gmail.com OPERATIONAL STEPS Objective: To draw a simple road project with different slope inclinations and slope heights and perform the calculations. 1. Create a simple road with a width of 10 meters and slopes as follows: - The first cut slope with a slope inclination of 1:1 and a slope height of 15 meters. - ...
Autocad Civil 3D - Box Culvert - Kutu Menfez
มุมมอง 20Kปีที่แล้ว
Create box culvert with assembly and its calculation. Tip kesit ile kutu menfez çizimi ve hesaplarının yapılması. Contact for assembly: civil3d.designer1@gmail.com *Skewed box culvert is not drawn with box culvert assembly. *Kutu Menfez tip kesiti ile verevli menfezler çizilememektedir. OPERATIONAL STEPS Objective: To draw and calculate a culvert project for an existing road. *It should be note...
Autocad Civil 3D - Harçlı İksa Duvarı (Duvar Boyutlarının Lineer Değiştiği)
มุมมอง 2.1K2 ปีที่แล้ว
Shoring Wall (Linearly Changing Wall Dimensions) Contact for assembly: civil3d.designer1@gmail.com OPERATIONAL STEPS A simple road with a 3:2 slope, 5 meters in width, will be drawn along a 100-meter route. An shoring wall will be constructed on the right side of the road, having the following specifications: - A fixed height of 2 meters between 0-40 meters. - A linear increase from 2 meters to...
Autocad Civil 3D -Arazi Yüzeylerini Tip Kesit ile Belirlenen Sınıra Kadar Birleştirmek/Kısaltmak(V2)
มุมมอง 2.3K3 ปีที่แล้ว
Combining or Shortening Existing Surfaces to the Limit Specified by Assembly Contact for assembly: civil3d.designer1@gmail.com
Autocad Civil 3D - Kesit Editörü ile Yüzeyleri Uzatmak - Extending surfaces with Section Editor
มุมมอง 2.9K3 ปีที่แล้ว
Contact: civil3d.designer1@gmail.com
Autocad Civil 3D - Farklı Dolgu Yüksekliklerinde Hacim Hesabı
มุมมอง 3.3K3 ปีที่แล้ว
Autocad Civil 3D - Farklı Dolgu Yüksekliklerinde Hacim Hesabı
Autocad Civil 3D - Enkesit Yüzey Kırıklarında Çizgi Uzantılarının Oluşturulması
มุมมอง 1.4K3 ปีที่แล้ว
Autocad Civil 3D - Enkesit Yüzey Kırıklarında Çizgi Uzantılarının Oluşturulması
Autocad Civil 3D - Creating Dynamic Surface and Profile Elevation Label on Alignment
มุมมอง 1.5K3 ปีที่แล้ว
Autocad Civil 3D - Creating Dynamic Surface and Profile Elevation Label on Alignment
Autocad Civil 3D - Dinamik Etiketli Şevli Kotlu Plan - Dynamic Corridor Elevations Label
มุมมอง 2.4K3 ปีที่แล้ว
Autocad Civil 3D - Dinamik Etiketli Şevli Kotlu Plan - Dynamic Corridor Elevations Label
Autocad Civil 3D - ITRF Koordinat Sistemlerinin Yüklenmesi (3 Derecelik Dilim Genişliğinde)
มุมมอง 6K3 ปีที่แล้ว
Autocad Civil 3D - ITRF Koordinat Sistemlerinin Yüklenmesi (3 Derecelik Dilim Genişliğinde)
Autocad Civil 3D - Farklı Eğimlerde Palyeli Şev Oluşturulması ve Şev Taramalarının Yapılması
มุมมอง 3.3K3 ปีที่แล้ว
Autocad Civil 3D - Farklı Eğimlerde Palyeli Şev Oluşturulması ve Şev Taramalarının Yapılması
Autocad Civil 3D - Sıyırma Kazısı ve Üç Yüzey Arasında Hacim Hesabı
มุมมอง 3.3K3 ปีที่แล้ว
Autocad Civil 3D - Sıyırma Kazısı ve Üç Yüzey Arasında Hacim Hesabı
Civil 3D - Arazi Yüzeyini Tip Kesit ile Belirlenen Sınıra Göre Aynı Eğimde Uzatmak/Kısaltmak (V1)
มุมมอง 1.7K3 ปีที่แล้ว
Civil 3D - Arazi Yüzeyini Tip Kesit ile Belirlenen Sınıra Göre Aynı Eğimde Uzatmak/Kısaltmak (V1)
Autocad Civil 3D - Harçlı İstinat Duvarı (Duvar Kalınlığının Otomatik Hesaplandığı)
มุมมอง 2.1K3 ปีที่แล้ว
Autocad Civil 3D - Harçlı İstinat Duvarı (Duvar Kalınlığının Otomatik Hesaplandığı)
Autocad Civil 3D - Harçlı İksa Duvarı (Duvar Kalınlığının Otomatik Hesaplandığı)
มุมมอง 2.4K3 ปีที่แล้ว
Autocad Civil 3D - Harçlı İksa Duvarı (Duvar Kalınlığının Otomatik Hesaplandığı)
Autocad Civil 3D - Label Slope on Corridor Links in Section View
มุมมอง 3.3K3 ปีที่แล้ว
Autocad Civil 3D - Label Slope on Corridor Links in Section View
great jobs, could you share these assemblies, thank you?
can i get your pkt file
Great work bro , how can I get link to subassembly for step excavation?
th-cam.com/video/fMXiF-a-2tM/w-d-xo.html
Elinize sağlık 🎉 mümkünse kullanmış olduğunuz sitil dosyasını gönderir misin
Emeğinize Sağlık Hocam Güzel çalışma
Çok teşekkür ederim Utku Bey.
please share dwg
Hi Moatef, you can contact me via my e-mail address.
Assembly Ücret nedir ?
civil3d.designer1@gmail.com mail adresimden iletişime geçebilirsiniz Elder Bey
Exceptionally great work !!!
Thanks for your comment🙏🏻
Diş kazısı ile ilgili bütün detayları düşünmüşsünüz mükemmel bir çalışma emeğinize sağlık civil3d ile çalışan meslektaşlarımıza faydalı olacağı kesin 💯
Çok teşekkür ederim Mehmet Bey🙏🏻
Tutorial please
amazing work sir, you are perpect civil design engineer....can u share file pkt or can u explained how to make it in SAC
Thank you very much, please contact me via my e-mail address.
What's your email...?
civil3d.designer1@gmail.com
Sir please share these assembly with me
Please contact me by email.
Öncelikle tebrik ederim. Udemy de eğitim programınız var mı?
Teşekkür ederim Tekin Bey. Eğitim videolarım yok maalesef.
Amazing job keep your great work and sharing with us and thanks Please share the DWG & subassembly Pkt file?
Please contact me by email.
This wonderful work sir Can i get the subassembly pkt file please? Thank you
Please contact me by email.
hocam merhaba hocam bu şev civil ın ıcınde var m ıyoksa sız mı hazırladınız paylaşabılırmısınız
Civil'in içinde yok, benim yaptığım bir tip kesit Ahmet Bey. Mail adresimden iletişime geçebilirsiniz.
İyi günler, TH-cam'daki videonuzu izledim ve farklı türdeki iki bölüm arasındaki bu bağlantı düzeneğini elde etmek istiyorum.
exelente amigo pero a las entradas y salidas de las estructura le hace falta el murete que es variable en altura lo cual se debería de poder editar o controlar
Hi Aquino. Are you talking about the piece of wall shown in that video? th-cam.com/video/er-zgl9plt4/w-d-xo.htmlsi=VYp79O8i2aS8He72
Çok teşekkürler sesli olarakta anlatım yoluyla olsa çok daha keyifli olurdu. Beğenerek takip ediyorum emeğinize sağlık kolay gelsin
Çok teşekkür ederim Ozan Bey.
Sir, excellent demonstration. keep it up your good work
Thank you very much for your comment.
Tebrikler çalışmalarınızı beğeni ile takip ediyorum kolay gelsin.
Çok teşekkür ederim Akın Bey, yorumlarınızla her zaman destek oluyorsunuz.
PERFECT
Eline sağlık
Teşekkür ederim Recep Bey
Can you send me pkt file bro
Hi Bekalu, please contact with me by e-mail
Sir it's really amazing and impressive work. Keep it up. Expecting more videos from you.
Hi Bhatti, thank you very much for your comment.
Gördüğüm en çılgın subassambly composor kullanıcısınıız hocam emeğinize sağlık güzel çalışma
Teşekkür ederim Utku Bey😄
Emeginize sağlık hocam profesyonel bir çalışma olmuş sadece o pkt dosyasının hazırlanması bile büyük emek her şey düşünülmüş bu tür uygulamaları bizlerle paylaştığınız için de tüm meslektaşlarım adına teşekkür ederim.
Çok teşekkür ederim Mehmet Bey
how i can ask this assembly?
Hi Aruelo, please contact with me by my email adress
i am happy to get this chance any pdf send me plse
Hi Lake, unfortunately I don't have a pdf document on this subject.
Please make this video in english version. Thanks.
yo tengo plugin para odt, si lo quieren me hablan, en mi perfil de youtube esta mi contacto
Can i have this pkt file?
Please contact me by email.
Gracias por el aporte, estoy interesado en conocer como es el .pkt. Me gustaría crear uno y no sé como hacerlo. Un saludo
Thanks a lot. Please contact me by email.
yo tengo plugin para odt, si lo quieren me hablan, en mi perfil de youtube esta mi contacto
Nice Work, I have one Question did you Create wing for box Culvert by Assembly ?
Hello Mahmoud. Yes, I made the entire assembly, including the wings, with the Subassembly Composer program.
Hi. Good job. Could u please share a small tutorial about the inlet or outlet assembly. Just the idea behind creating a progressive assembly. Thx
Hello Elmourid. For assembly, please contact me my e-mail.
Merhaba tipkesit ve DWG dosyanizı paylaşma şansınız var mı ? Çok güzel çalışma olmuş emeğinize sağlık.
Murat Bey teşekkür ederim, tip kesit için mailden iletişime geçin lütfen.
videodan ses gelmiyor hocam
Videoları ses olmadan oluşturuyorum Civan Bey, mümkün olduğunda anlaşılır çekmeye çalışıyorum ama takıldığınız yerleri buradan veya mail adresim üzerinden sorabilirsiniz. Mutlaka cevap vereceğim.
@@AutocadCivil3D hocam merhaba kolay gelsin hocam sizde menfezin ptk dosyasını bana göndereblirmisiniz
I am interested to learn your skewed culvert please send a copy of your drawing.
Hello, please contact with me by my email adress.
thank you for chanel.
Thanks for your comment Huỳnh.
videoda neden ses yok
Hamza Bey merhaba. Videoları, ses olmadan da anlaşılabilir bir şekilde çekmeye çalışıyorum, ama bunun yeterli olmadığı veya anlamadığınız yerler için bana yazın, mutlaka geri dönüş yapacağım.
Excelente video y uso del PKT. Saludos desde Perú
Hello Paredes, thank you very much for your comment.
very impressive.. can u share to me pkt file? i already email to yo
Hello Marcgun, thanks for your comment. I reply to all mails sent to me, please check your mailing address.
can you share the dwg and pkt file？
Thanks for your comment, please contact with me by e-mail.
Kindly share the file thanks
@@rolandojrmontemor174 Hello, please contact with me by e-mail.
Tebrikler...Anlamayana, tatlı dille anlatan güzel bir çalışma...
Can I get the style?
Please contact with me by e-mail.
Emeğinize sağlık, Kanat duvarlarını subassemblies de nasıl yapıyoruz bununla ilgili bir video paylaşmanız mümkün mü?
Evet güzel çalişma anlayana : ) İŞ VE DIŞ KURP OLAN YERDE KISMEN DENGELİYOR AMA TEK KURP DA KESİNLİKLE AVERAGE END AREA METOTU KULLANILMASI LAZIM.
Teşekkür ederim Ahmet Bey, çok doğru bir konuyu belirtmişsiniz.
Kübaj tablosundaki uyumsuzluğu anlatan güzel bir çalışma olmuş :)
Çok teşekkür ederim i.sayin :)