- 9
- 46 745
Truck Tech Tips
United Kingdom
เข้าร่วมเมื่อ 20 ม.ค. 2022
Truck Tech Tips are all about real life automotive diagnostics. How to perform tests that will assist with fault diagnosis to make the Technicians life easier. The plan is to create videos that show realistic processes for testing electrics, fuel, SCR and communications systems.
The areas will not be limited as we will create videos based on the viewers needs, what YOU need to know and want to see.
We want to incorporate oscilloscope testing as this is becoming more and more common and necessary for accurate diagnosis. Hopefully you will get something from the channel that helps you back at the workshop and makes your day to day work life a bit easier 😊
The areas will not be limited as we will create videos based on the viewers needs, what YOU need to know and want to see.
We want to incorporate oscilloscope testing as this is becoming more and more common and necessary for accurate diagnosis. Hopefully you will get something from the channel that helps you back at the workshop and makes your day to day work life a bit easier 😊
Toyota Auris Powerdown
This video shows the powerdown procedure on the Toyota Auris. This is the same procedure for the Prius (battery in the luggage compartment).
All EV work should be carried out by qualified Technicians.
All EV work should be carried out by qualified Technicians.
มุมมอง: 27
วีดีโอ
Maxus Edeliver R9 High Voltage Powerdown
มุมมอง 9521 วันที่ผ่านมา
This video demonstrates the high voltage power down procedure for the Maxus Edeliver R9 van. The steps followed in the video are in line with UK EV Technician rules. Do not attempt to work on any high voltage circuit if not suitably qualified and following the rules in your region.
Relative Compression Test Cummins ISBe
มุมมอง 250ปีที่แล้ว
Here is a short video showing you how to do a relative compression test using the Picoscope and also how to obtain the injector, camshaft and crankshaft sensors on a Cummins ISBe engine.
Cummins ISBe Injector Scoping
มุมมอง 190ปีที่แล้ว
A short video showing how to scope the voltage and current on a DI Cummins fuel injector. The scope used is a Picoscope 4425A using the latest pico7 software.
Voltage Drop Test
มุมมอง 3Kปีที่แล้ว
Here is a quick video showing the V1 to V4 voltage drop test. This will highlight whether your fault is on the positive or negative side of the circuit. Plus, it shows how something as simple as a fuse can can cause a fault if it hasn't completely blown.
NOx Sensor Testing
มุมมอง 31Kปีที่แล้ว
A quick video showing how to check the NOx Sensor circuit to determine whether the issue is in the loom or the sensor. The test was carried out on a Renault Midlum but can be adopted for other manufacturers. Light vehicle Technicians can do the same test. Just expect 12V as a supply voltage not 24V.
How to test SENT Sensors
มุมมอง 830ปีที่แล้ว
This is short video that shows the expected values when testing SENT sensors and details how to set up the Picoscope to view a SENT sensor signal.
BMW 118i Drivetrain Warning and Engine Derate
มุมมอง 2.5Kปีที่แล้ว
A very short video just highlighting viewers on a potential issue that can show as a wastegate actuator fault on the 3 cylinder BMW 118i engine. This was on a 2017 model. The initial engine codes were permanent and would not clear until I disconnected the battery then reattempted to clear using the scantool. The engine ECU pulls back the throttle and boost when the clutch slips but also logs th...
Renault Midlum CAN Bus Basic Tests
มุมมอง 9K2 ปีที่แล้ว
Hi all, here is a quick video highlighting the voltage and resistance tests that can be performed on the powertrain CAN Bus network. These issues normally give non start faults and network DTCs.
Could you do another one. This time with a buried faulty cable power or earth?
Thank you for the well explained process. What was this fuse operating please?
This is fuse 7 in the engine compartment fuse box (next to the pcm). This one fuse feeds a lot of components. Inlet cam solenoid, oil pressure control valve, coolant pump relay, canister purge solenoid, turbo pressure control and bypass valves. It feeds the red/yellow wire to each of these components.
Interesting measurements but I bet if you disconnected the NOx module while the truck was running you'd get a DTC that was shouting that something was wrong with the comms to that unit so most of these measurements could be short-circuited, so to speak.
True, but what if it wasn't on the CAN. I had a NOx fault where the issue was a voltage drop on the earth. Loading the circuit at the sensor proved it. Comms issues are not always relating to comms wires.
Can you explain about 6 wire socket nox sensor Man truck
Hello there. I haven't specifically seen the MAN 6 wire sensor, but I have seen 5 wire sensors which contain 2 earths, 1 positive and CAN High and CAN Lo. I will have a look out for one and do a video on it. Thanks for the question.
Nice work. Very helpful.
Great job, Thanks for sharing! Is there a way to test the actual sensor, not just the module?
Hi, there are a number of NOx/O2 sensor tester kits available in the market. My friend has one. I will find out the make and model and let you know.
Do you have a video for 5 pins as well? My nox sensor 2 has 5 pins. Yours in video is with 4 pins. I changed the nox sensor and now is failed again. P229 FO9 NOx sensor 2 (cylinder bank 1) has a malfunction. There is a component fault. --NOx sensor 2 (cylinder bank 1) has a malfunction. No signal change: Voltage level is too low.--The switchover between the maximum and minimum values of NOx sensor 2 (cylinder bank 1) is too slow. There is a signal below the permissible limit value. .. i changed one nox sensor and i suspect to by problem with wiring and not nox sensor. Thanks
Hi there, what vehicle is it fitted to? Some 5 wire NOx sensors do no use the 5th wire. So they only have a positive, negative, CAN Hi and CAN Lo. Sometimes you can get downstream NOx sensor issues if the SCR catalyst is not performing as it should.
Thank you so much
Is it the same procedure on the Iveco Stralis 450 E5 2007? The problem is that after replacing the sensor, it reports an error: LONG TERM NOX SENSOR FAILURE DTC:45F. By replacing the sensor (from another manufacturer), it reports an error :NOX SENSOR FAILURE DTC:1A3! Three new sensors have been changed and all three are showing errors. I ask for help and advice. Thank you!
Hi there. So there are a few things to consider. Firstly you need to make sure that the NOx sensor that you have fitted is the exact component for your vehicle. Different manufacturers may have CAN High and Low swapped round. Secondly are there any other DTCs stored? Do you have any for EGR for example. The EGR also assists with the reduction of NOx. If there is an issue with this system NOx levels will be higher than normal. Thirdly, does you vehicle have a pre and post NOx sensor or just a post NOx sensor. Potentially the SCR catalyst could be an issue although this is only in extreme cases. Just a few things to consider.
Thanks for the reply, problem solved. The problem was in the SCR catalyst. Thank you!
What's that component called at 0:32?
That’s the turbo wastegate actuator
Fantastic outline of the procedure, definitely going to subscribe
Many thanks. Should be creating more videos soon.
Clearly explained, thanks for this. I'll be testing those points on my sensor.
Thank you.
I replaced the cultch and my drivetrain fault is still there what shall I do now?
The drivetrain fault can be caused by many issues. You will need to connect a scantool the read the stored fault codes.
Would you recommend getting a 2 or 4 channel picoscope? thank you !
Hi, I would always recommend going for more channels if possible. This means you can measure power/ground and signal at the same time when you are looking at most sensors. Really depends on your budget. I have both, I started with the two channel which cost me £150 ($195). Relatively cheap, but got me used to using the software.
Thank you the video is super helpfull and in good detail
You're welcome! Thank you.
Some great videos, hope you will be doing more..
There will be, hopefully soon 👍
I have a 2008 Midlum and the display/dashboard is not working at all after boosting the battery with a battery staring robot. Everything is working properly except the display. Checked everything the relays and fuses there is no fault. The diagnostics device cant access the display module ... have you meet some similar problem?
Hi, we haven't had that fault, but here are some things you can check. Remember the cluster is just another module so it needs a few things to communicate, powers, grounds and connection to CANbus. If these are all there then the cluster module could be at fault. There are 3 plugs on ours C, B and J. Plug C pin 13 is the cluster ground. Plug C pins 11 and 12 are high speed CAN check your resistance and voltage at these pins. Plug J pins 1 and 2 are diagnostic CANbus, check you have approximately 4V and 1V (CAN Lo and Hi) respectively. Plug J pins 6 and 8 are high speed CAN so check your resistance and voltage there. Finally plug J pins 10 and 23 are power supplies. If you have all of these then it looks like the cluster module (MID140) is at fault.
Hi! As a feedback for the tips above You have right. The fault was at the cluster module, the resistance and the voltage was exact as you mentioned... I'm grateful to you that you answered my question and for the useful answer, we have saved a lot of money (replaced the module with a used one for pennies). Thank you for sharing your knowledge! @@trucktechtips638
This is the difference between a real mechanic and someone who just replaces parts. Anyone can replace a part.
Nice job and what a cracking video. Not so common to find corroded fuses and sometimes not possible to see this resistance with the naked eye. Hell of a drop there 👍
Thank you. It definitely was an unusual fault. Proof that checking for voltage drop is a great diagnostic test. 😊
👍
👍
👍
Very interesting thanks 🙏
Glad you enjoyed it
Fantastic explanation but this is why I teach my apprentices to use test lights on fuses.
Absolutely. The test lamp is still one of the fundamental pieces of diagnostic equipment that should be used when checking circuits.
Excellent presentation of a simple method of narrowing down the problem... Saving!
Glad you liked it, many thanks.
Hello, thanks for video
You are welcome 👍
nice job thank you for sharing I have questions what is the car and what is consumer connector was ?
The car was a 2012 Audi A4 1.8TFSI. The fuse was number 6 (15A) in the left plenum chamber (next to engine ECU). This powered the engine component supply relay coil and three of the fuses in fuse panel c (at the side of the dashboard). The three fuses where for clutch pedal switch interlock (5A), fuel pump control module (25A) and brake light switch (5A). I used the free wiring diagram CARMIN STD in the app store to find it.
beautiful
Thank you! 😊
Hi as an aside is there a way of using the NOx sensor to detect Nitric Oxide at parts per million as a stand alone test set, the real one cost $885. I have a iNO generator on my workbench bench and want a test sensor
What an interesting question. I scraped a pass at Chemistry at school so take my answer as one not coming from an expert. In theory, yes, your commercial NOx sensor can measure in the region of 0-1600ppm. The term NOx that is used is only the collective term for Nitrogen Monoxide (Nitric Oxide) and Nitrogen Dioxide I believe. The iNO generator you have is this a respiratory machine? Have a look at this article I found about NOx sensors. There is a fair bit of reading in it but it discusses what the sensor is actually doing. dieselnet.com/tech/sensors_nox.php#:~:text=The%20NOx%20measurement%20range%20is,%C2%B110%20ppm%20%5B3899%5D%20.
easy way&greatlly diagnostic job.thank y for yr explanation.
You are very welcome.
Perfect diagnostic methods. Will be subscribing 😁
Thank you 😊
Thanks for video
You are welcome 😊
Thanks man very well explained 👏
No problemo! Many thanks
Awesome share. Thank you so much!
You are very welcome 😊
Thanks boss,really very beneficially.
You are very welcome!
Can please give a little info on the scan tool you used? ie: make Ancel...model?
Hi Neil. It's an Ancel X6 HD, they retail about £450.00 ($545.00). You get what you pay for with scantools. We haven't had any success with it on Iveco. DAF, engine and SCR faults but no ABS. Volvo, Renault, Dennis pretty good to be fair. The tool allows for 1708 CAN diagnosis which is helpful on these models.
@@trucktechtips638 Thankyou
Finally, someone else using a picoscope on a truck! I work on Cummins in the States and just got a 2204a. Thanks for the video and keep them coming please! If you know any others on youtube making videos with a picoscope on a truck please share!
Many thanks for the comment Paul. There will be plenty more Pico videos to follow.
Thanks!!!!!! keep them coming finally some who works on European trucks who presents in english great job man
Many thanks, definitely more to follow.
Good job on your presentation however the high speed can on these Vovo is green and yellow & orange and purple on j1708 just an observation
Many thanks for the comment and the clarification. Much appreciated 😊
Very informative. Thanks.
You're very welcome.
Very good explanation of canbus. Ive worked on HGV's for years (not in dealerships) and have muddled through with very little training. These types of video's are excellent. Thank you 👍
Many thanks Daniel. Anything that helps is always useful when you are a tech. There will be more regular videos to follow.
Bravo.......is it true......by unplugging the 120 resistor it will start blinking the codes on engine light chanel .....dash......old cars...cheers
I haven't experienced that myself Matt but to be fair it depends where the break or issue is. Volvo FE/ Dennis's where always bad for the CAN lines breaking right at the Engine ECU so you wouldn't have communication with the module and no DTC's available on the Scan Tool or Instrument Cluster from the ECM.
Thumbs up👍
Hi, see you again.