วีดีโอ

Hi, where did you purchase those cables? Thank you

Where is the wire diagram for autohex? Thanks

Hi really good video! I need to buy programming tool for mercedes would u buy vvdi mb tool like yours or cgdi mb? Any feedback i would be very grateful 🙏

Bravo

Great job, do you have a video or suggestion about cloning a new version of w164 ? it is from 2009 to up

Excuse me my friend who model opel is this?

To cloning ECU , you should have to smoke shisha

لازم اشرب اركيلة مع البرمجة وضروري يكون المعسل تفحتين ؟ أنت مبدع 👍 يعطيك العافيه

Hello Markos I need your contact plse I need training from what your doing thanks

Markos I have a similar issue with rear sam for a mercedes ml w164 2009 Can you help me in any way?

Hi Mr, i like to watch your videos and I would like to learn this job am a car locksmith from Kenya

I followed your instructions today and got a used ESI programmed on a W166 today thanks

Did u short circuit it?

Hi good video . Would love to watch a proper tutorial which shows from start to finish including the tools needed basically the set up .. there are so many tools and videos out there but nothing that will show step by step of the whole process . Thank you for creating this tutorial.

W205 same ?

Can’t see anything what you doing

Where do i get VVDI and the hardware?

you dont want help us .. why you dont explen pincode work .

What program is that?

Is this for programming if you have no keys at all ??

after you renew the ecu which tool did you use to programme it to the car?

Hola tengo que cambiar un cas 3 de mini cooper debería ubicar uno con la misma referencia o podria adaptar cualquiera gracias

Hi bro how can i get online software update for Mercedes.Please help me how to get this access?

Thanks for u video, The ESL u used,is it new of used one plz?

Hi Job well done, can I use a coil from any car?

Where are you located? What scan tool do you recommend to reprogram tcu for range Rover supercharged 2009

Thanks for this video

Where did u get the microscope with light?

Not good, can’t see anything plus clearly doesn’t have the right tools to open the module.

five-pin round connector next to the USB for what purpose?

Hello. Why do you subject the PCB to unnecessary heat treatment instead of using the much more efficient Round Pogo Pin Metal Needle Tools?

Thanks I did read Corsa d. Eeprom and d flash I uploaded file to get iprog. Not luck

nice

Nice jobb,just you forget to write vin first☺️

nice jop

Do all ELV modules repaired with a new motor have to be programmed again for them to work?thanks

Great explanation, thank you very much

Very good tool I need one

1:09 cant get those pins out

What adapter to VVDI do u use ?

Thanks a lot of, man... Can u show how to make a full complect for astra g containing ECU+CHIP+IMMO ? And how to use Immo pin-code for programming with ECU?

Hi.........I want to buy the magic box and can you help me choose the standard protocols to start the job and 1000 thank you

Hi. i need nmr for WhatsApp I am Ayoub you Friends from morocco. ✌️

Thanks for sharing👍🏻 my humble note: 1:Wrong soldering tip 2:too much solder

Hello Markos, after cleaning the whole unit I've checked it with minor microscope and there's no clear signs of rust or any other symptoms, but when i plug it to my car + fully reprogram it, I still face issues with fuel gauge + front door lock etc.. any recommendations/advice? before spending a fortune to buy new one!

Thanks mate its help me ❤

Hi how much cost this tool to buy I like it

Password no need ?

Boss pa rapier naman ako ng ECU

i cant see anything...