วีดีโอ

Oh my! My weather strip didn't even remotely come off like that. It was so stuck and rotted, that I near pulled my hair our scraping it. Good of was the way at the time. I got it cleaned up and replaced, but went out today to buy a heat guns for all the other ones. I will clean it all up with goof off for a smoother clean after the heat gun removes the big part. Donyou think the heat gun will melt the old caulk around the outer edge that you first showed? Guess ill find out. This is not my area of work, but if I want it done ill have to learn as my hubs doesn't think it needs it be replaced. Thanks for the tutorial.

Curious if your jeep is still alive

So...I'm interested for sure...can u do color's?... Like yellow or green?

That one is so much better than the original

And then goes another 1 😢

Or the cat is bad most likely but you gotta make it go lean and rich to test to see if it's lying or not

Just bought 2 of these on your eBay store! This is my son's favorite little bow, so glad he can get it working again!

When you changed the pcv did your jeep burn less oil?

Found this video. I got a 06 commander and can’t find out why I have rear vibration under slight heavy acceleration. I even replaced the whole rear end. I never suspected the drive shaft because the u joints were still ok. The feeling it gives me is like an unbalanced DS. So this might be my problem

thank you for the help brother

The shutdown portion of time is not relevant as people usually do not wait till end of shutdown. The startup time is more relevant

Should have changed the u-joint as well thats probably causing the rumble and vibration u heard and felt on the test drive. Did u have an annoying scraping noise before replacing the cv joint? Just curious

Why don't you change the Flyers to the correct motion there you know the clippering pliers dumbass

Cool, isn't it ??

took my off, PCV rubber turn into platic and broke off inside the cover . Had to carefully pry the ring out without breaking it. Took me a 1.5 hour to get it out. Was stressing about it. I used a vise grip and a screwdriver to work it out also lubricated with a few drops off oil.

i have the same code reader and a 2003 Tj 4.o with a po175 code lmao 🤣🤣🤣

i pulled mine out without dropping the trans cross member

Can you make a bristle one so it doesn't tear the flights up. That's the problem with them

We bought some of these, but the new rest is chewing up the fletching on my daughters arrows. Any suggestions? I tried filing it down a bit, but that is just lowering the arrow in the rest and bringing the top fletchings down into the groove as well.

8yr old vid but for anyone just seeing this, if your frame (or the one you're wanting to buy) looks this bad, don't walk, RUN AWAY. One pothole and that frame will fold like a taco. For those (including the OP) thinking spraying a rust prohibitor such as Eastwood will correct the issue and prevent any more damage: *WRONG*

What model meter is that?

I have the same issue with TYGER brand hitch from Amazon.... Left light blinker doesn't work and it's acting weird with the harness, trailer lights don't come on at all ...

I see that you only ship to the US. Is it possible to get the 3D file and print it myself? I cant' buy it anyway since I live in Norway.

Worked like a charm. Thank you

Thank you some much your a life saver

Yessir!

I need to know what was the sound and vibration like? My 2005 jeep grand cherokee 5.7 hemi vibration is like driving over rumble strips by the side of a highway, wondering if yours was the same?

heres a way to get rf burn take of the antenna then touch the antenna connector while hitting the transmit.

i saved the link to your ebay in my email as if i ever break one i will order it. thanks for this info.

boy i would love to get a couple of those. i bought 2 for christmas.

Which Graphic Card Did U Install Sir ?

Same thing happened to me...3 shots in and it broke... Just went and grabbed one of another one

Can you make one where the two triangles are off center. So that it fits different arrow notch orientations.

Take the pivot pin out of the pliers and put it in the other hole . The pliers will now work the opposite way .

33:05 you just made yourself a mess

friend I have a grand Cherokee laredo 2007 3.7 and when I reach a speed of 100 k / H a buzz grabs him and if I pass that speed it takes away you think it is the cv joint

Wife broke her arrow rest within one evening of shooting. Got 5 of these just now from your eBay site. Thank you very much.

Slinging grease and not packing grease.

I fell asleep. When i woke up your hands were still clean and still disecting the parts. Ouch sandpaper! Chrome dont get ya home. How much to balance?

I have a 2006 Jeep Grand Cherokee and on bumps I hear like a clicking noise like something loose and around 40-60 it vibrates. Do you have a clue on what it could be? Thank you

OK I found it you went with steel is there any difference in the way the car drives performance I mean going from aluminum to steel

Can I get the website where you ordered this driveline and a part number I called the dealer they want $1500 for it

My Windows 7 Pro It starts in winchester in 10-15 seconds

My 2010 grand Cherokee only vibrates under acceleration. Could this be it?

will this work on the re-curve model?

Hey try it with a Abbree 124cm tactical follding antenna ..20 nzd

Clamps are available at NAPA Auto Parts, They are just CV Boot Clamps. They also have the tool for them in the Service Tools line.

How do i go about ordering the centershot arrow rest. I looked on amazon and could not find it

I thought RAM/ memory was the speed, not the drive.

bro this made me get that