วีดีโอ

Give it one more tap for good measure 🎉

Very informative Jim .Wish id seen this video before. I can show it to my repair garage to avoid any confusion .After all these new clutch parts sticking first and reverse gear began again .

2003 passat 1.9tdi 130bhp 6 speed manual is this compatible

Would this work in a b5. 5 passat 6speed gearbag

I've got a 2012 Mk6 GTI that has recently had the infamous mainshaft bearing noise problem. I've been driving the car daily for a couple weeks after first hearing the noise, trying to keep away from 4th and 6th gears where it's most audible (was just about to perform the bearing washer repair tomorrow! what bad luck/timing), but all of a sudden today when shifting from 1st to 2nd the transmission made some terrible sound and now won't go into gear. Shortly before this happened, I had the car go through a lite touch wash; almost immediately after pulling away from the car wash, I heard a small knock sound, as if something may have broke.. it was faint enough where I didn't initially think much of it.. but then 2-3 min of driving later is when the transmission failed to go into 2nd gear from 1st (from standstill). Luckily I was very close to home, so I coasted into my driveway from there. It appears the shifter linkage works (can see the linkage moving when changing gears), but when pressing clutch in (engine running) and shifting into Reverse or 1st, it doesn't go into gear at all. Engine runs perfectly fine. Would the mainshaft bearing issue all of sudden have worsened to the point of failure?

Does this shim work in the 6speed manual transmission in 2012 gti? Transmission has the plastic cap. How much play does it take for it to fail?

Hello,for vw sharan,FVA gearbox(6S),fits?

Thanks for the video. Aftermarket cover: FEBI 47167

Did you reuse the plastic cap?

This work with Audi a3 automatics 7 speed ??

Is it 2002 vw sharan 6 speed manual gearbox may have same issue?

Would this apply to a 2016 passat. I have a decel whine and sticky 2nd gear.

Gracias por tu video...me puede decir medida para seat Alhambra 1.9tdi 115cv 2004. Gracias

Works on seat Altea xl freetrack 1400tsi 2011 6 gears manual transmission??? please someone answer

Recently, I'm having this similar grinding/rattling sound at 3rd gear deceleration. But mine is a dsg gearbox. Does this fix apply? Or it's for manual trans?

Will this kit work on a 2006 Audi s3 2.0T 6speed manual transmission?

bought the kit including new end cap for £20 Fitted and 1st gear selection is back to normal BIG thanks

If my bearing isn't spaced will that be a problem, and can i change the bearing without stripping the gearbox?

hello there, I have same problem on my golf mk5 2.0TDI 6 gear but I don't know what are OEM numbers and where I can order these parts. Please if someone can help me. Thanks!

This may be a foolish question but does this cap require changing when doing a clutch change?

Had a quote of £700 to rebuild my gearbox . I had a whine in 3rd . Done this and da da . Whine gone . Very cheap fix ( seat Leon MK1 cupra)

does this work and fit the octavia vrs petrol 2008

Hello! This video is a revelation. However, i have the 2002 version of the 02M. Do you know if the shim also fits on this box?

Can i do this for 2.0 tfsi audi a3? Or it's only for tdi?

This resolved a reduction and shift whine I had in 5th thank you

Hy, hope you will help me with something, i just have changed the clutch with all the parts, pressure bearing, pressure plate, flywheel, clutch disc, and the clutch pump (the clutch pump was changed to solve the problem, but it wasn't from there), after that a problem it appeared. Now sometimes i can't get out of speed 1 and R, i mean, i don't have any other problems with the rest of the speeds.. My clutch pedal it's slack, the air from the installation was removed 3-4 times (different periods). I saw the problem it's show when the engine getting warm. It's embarrassing, cause i can't park the car normally, cause it remains blocked in R speed even if i have the clutch pedal completely down. The problem manifests itself in the following way: i press the clutch pedal for example, i put the lever in R speed, i try to release the clutch pedal slowly and when i feel the gearbox has engaged, i press the pedal again to the ground, but the gearbox it's stay engaged in R speed and i can't get it off, i can release from R to neutral just if i stop the engine.. I hope I made myself clear...

Hey Jeff, Good stuff man thank you in advance, Currently have my tranny out the r as well and having similar issues to the folks in the comments. Gear lock out, Creeping, so on.. Have some questions though! Doing research a while back i purchased a 02m slave cylinder shim kit nothingleavesstock.com/online-store/#!/02M-02Q-clutch-slave-shim-kit/p/13912883/category=2903030 in hopes that when the time came this would be included in the work i plan on doing. Im just now seeing your video, seeing simplicity + effectiveness and wondering.. what to do lol. And are these shims essentially closing up the same gap/movement in the shaft?? one from the cap end as in your video, and the other(mine) from the slave cylinder? If nay, do you recommend one or the other? Both? and if they have different applications, whats one/the other better for? much appreciated!

Where did you get the nifty picks you used on the snap ring?

YJJJKJJULKOPTMYYY 90P

Did the same thing on a SEAT LEON 2.0 tdi 136cp, 3 years ago and no problem since then. Had 5th noisy.

Did this nearly 2years ago.car still fine with no gear issues.just come back to thank jeff again for saving my ass out of 1grand.

Hey this work for Volkswagen CC 2010 manual Transmision 6 speed Please I need help

This is for Octavia 2? Oil must out? Thank you.

Iv done this onces and it worked but started agen do u think id get away with another shim

How hard is it to take out the bearing you can see in the video mine has fell apart and spray the cover off

I did this but still have slight play on the shaft. Seems like I need a thicker washer?

@Jeff Straker or anybody.. Do you know what size shim or what part number I would need to do this to my Mk5 Golf GT-TDI 140 bkd. Gearbox code O2Q? Thanks in advance!!

Hi my 2004 seat alhambra 1.9 tdi 130 seems creep forward in 1st gear or reverse with my foot down on the clutch fully too the floor, sometimes the gear will get stuck untill i turn off the engine then i can put it in neutral. The clutch biting point seems to be very close to the floor too. Its had a new clutch and flywheel by previous owner about 20k ago. Iv heard this may fix the problem!? What do you guys think. Thanks

Thank you Jeff! Worked perfectly for my Skoda Octavia. Repair parts 19€ vs repaired transmission 1400€. Here's before and after videos of my transmission. th-cam.com/video/MUn9fWk_q10/w-d-xo.html

I’ve got winning sound in 5th on 6 speed box will this help me as see comments others it did but sure there had 6 speed or 5 thanks

Jeff, i hope you see this message for i was about to purchase a new(to me) O2M do to play in my input shaft. in my case the humming sound was more of a click when i bought the car a few weeks ago and turned into an all out "Knock.' Do you think that shimming the bearing(barring its in good condition) will fix the problem? Really hope for some insight before i spend a big chunk of change on something not needed.

I have deceleration noise while I'm in 3rd gear ? While I'm.on the gas there is no noise. Would this be the fix? Sounds like 3rd isn't fully engaged and you can hear some metal rubbing sound, not really grinding id say but only in 3rd

reporting back.problem 5th gear whining gone no noise at all.i was about to spend £600.thank you jeff.

I am doing this tomorrow on a 2006 touran 2.0 tdi to resolve 5th gear whinning.I will report back once the job is done.

So does this work on 02Qs?

Great information in this video repaired my 2.0 TDI Sport Touran in the U.K. Got the parts from the local SEAT dealer WHT-001-976 for the washer/shim was slightly translated to EWHT001976 at this dealer and 02M-301-211-B was E02M301211b for the black cap. Be careful knocking in the cap with a soft hammer as I slightly dented mine, this can be avoided by only hitting it around the rim. Believe it or not the shim and cover only cost £11.05 total including tax!

Thanks for the video. The numbers for the parts are:WHT-001-976 for the Shim and02M-301-211-B for Cover

Thanks for this. Such an easy fix haha. Doing an R32 clutch and noticed this. Glad it's not very intrusive work.

hi mate thanks for the video have u got a part number for the shims? and where did u get them from thanks brian

neradi se to tako