วีดีโอ

It’s just another little piece of 1.25in pipe glued around the 1in pipe to act as stop. I think that’s the fitting you’re asking about?

Glad this was helpful, If you scroll through the comments I listed the part numbers for the ram mounts in some of my replies. And then I believe list the PVC components that I used in the video. Thanks!

I believe it’s about a foot below the pontoons, I can’t remember the exact measurement but I’ll try grab that measurement soon and post it for you!

Glad you found it helpful, thanks for the kind comment!

Lowe’s

If you’ll scroll through the comments, I listed the numbers in one of the replies previously. It won’t let me copy and paste it for you or I would. Thanks!

I mounted the box inside the storage bin at the front of the boat, I’m assuming the box needs to be protected from water pretty well, I haven’t seen the specific specs for that but you know how well water and electronics work together haha.

I run it on 24volt at 80 lbs and it does great in the wind, you can add a 3rd battery and get 100lb thrust on 36 volt but I haven’t seen a need for that yet, been in some pretty strong wind and it holds up.

RAM Mount Composite Short Double Socket Arm f/1.5" Ball Base, RAP-294U - 1.5" BALL W/ FEMALE SLIP PIPE, RAP-404U Medium Tough-Claw with 1.5" Diameter Rubber Ball

@@gabecordova8025 couldn't you use an adjustable 1" flag pole mount and mount that to the rail of the pontoon? Then put a 1in piece of pipe in your flag pole mount to your 1 in × 1 1/4 T. That would cut about $60 off the price.

@@jasonstokley7274 you could probably make that work and save some money, from my experience though, the versatility and ease of use of the Ram mount is worth the money for this application.

The flag pole mount has 4 screw holes, so I just used shorter screws that do not come through the top of the deck and haven’t any issues with it coming loose.

I’ll try to get that and post it for you soon, you just want the length of the pvc pipe?

@@gabecordova8025 My sun tracker is a 3 log boat. The logs are larger in diameter than a 2 log boat. I couldn't tell which you had. I really don't know if it is enough difference to worry about. I am more concerned about the 1 1/4" length to the flag pole fixture. I believe our decks are the same size from rail to brace.

I used a flag pole holder and I screwed it directly to the plywood on the underside of the deck. Then I used a 90° fitting with a piece of pipe sticking out of each side of the 90. One piece of pipe to go up into the flag pole holder in another piece of pipe to connect the PVC T-clamp. Hope this helps!

Glad it helped! 6ft long.

Spot-lock is great! 18 ft pontoon equipped with the Garmin Force Trolling motor.

This is my trolling motor on a 22' Sun Tracker ELP fishing barge, Minn Kota Ulterra i-Pilot GPS/US2 Bow-Mount Electric Trolling Motor - 60in Shaft 80lb Thrust. Spot lock can hold my boat in light wind. The 80 pounds of thrust moves it very well.

Thanks! They are listed in one of the comments already.

@@gabecordova8025 On the double socket arm there is another ball that is going into the pvc. That didn't come with that double arm part did it? Do you have the part number for that? Thanks

@@thomaselsenpeter2942 It’s RAP-294U, it’s a 1.5 inch ball with a female slip pipe. It has to be bought separately.

One more question. Where did you get the flag pole mount?

@@thomaselsenpeter2942 I picked mine up at a local hardware store.

I am assuming that you are talking about the part that connects the PVC to the ram mount coupler? If so, I bought a 1 1/2 inch ball with female slip pipe and just glued it into the PVC.

Ram mount components purchased online from Ram Mount website. All mounting brackets and hardware for Garmin units purchased from Bass Pro.

Glad it helped you out!

The long piece of pipe that goes down into the water is a 1 inch piece. There is just a short section of inch and a quarter that I have it ran through and then the T is 1.25 that reduces to 1” on the side that the ram mount attaches. So the 1.25 pvc pipe just buts up to the 1.25 T. I think you can see what I’m talking about at the 1:10 - 1:30 mark in the video. Hope that helps!

The 1” ball shouldn’t matter as long as all the fittings fit together. On the PVC set up, The T does slide up and down the pipe, I epoxied a small piece of 1 1/4 pvc just below the T so it can’t slide very far in that direction, and then the elbow at the top of the pipe keeps it from sliding any further in that direction, hope this makes sense.

Thanks Gabe...I traded back and went with the 1.5 setup... yes, I now understand the PVC rig... the pole does extend down below the pontoons right... did you use any particular epoxy?

Thanks, they actually make those PVC clamps, order online or pickup at Lowe’s. I imagine you could also cut a T open, but probably wouldn’t work quite as well.

Is that going to be the only graph you have on the boat?? I definitely recommend mounting it at the bow, you need it to be right there where you’re fishing. If you don’t have another graph I recommend adding something cheap at the console so you can find structure while driving.

@@gabecordova8025 ok yes I’ll have another one already installed at the console. Any recommendations on where to mount it on the bow? Deck, maybe on the railing? I think it would interfere with the mooring cover possibly.

@@MackZero I’m not really sure if your pontoon is like mine or not, but I have 2 storage compartments, one in each corner at the front of the boat. I mounted mine on the lid on of one of those compartments, you can actually see it behind me in the video. This also allowed me to put the other components down inside that compartment which is nice. If you don’t have that compartment then I would recommend mounting on the deck and using a riser to get the unit up to the right height. It would definitely interfere with the mooring cover if you put it on the rail, so you would need to put it on a removable ram mount just like I did for the pole mount.

@@gabecordova8025 Appreciate the advice! Subscribed!

I am using two of the Garmin 93sv UHD units. One at the console and the other is mounted to the lid of the storage compartment up front on the starboard side of the boat, there is a rod holder on that compartment, and I ran the wiring down through that rod holder and installed the network box inside of that compartment. My two Garmin units are linked together with a network cable so I can see the livescope on both screens at the same time. If you watch the video from 6:30 to the 7 minute mark, you can see where the front unit is mounted. I’ll try to get some pics or video of the setup when I get a chance. Glad this helped you out!

@@gabecordova8025 I GREATLY appreciate your response to me question above, I thought I had hit like way back then. I have finally saved up for my Livescope!!! Exactly How long is your 1" PVC Pipe?

@@gabecordova8025 Also, could you post or email me a short video of your Bow mounted 93SV. I have the same storage compartments you have. I appreciate your time and allowing folks to steal your ideas!!!!

RAM Mount Composite Short Double Socket Arm f/1.5" Ball Base, RAP-294U - 1.5" BALL W/ FEMALE SLIP PIPE, RAP-404U Medium Tough-Claw with 1.5" Diameter Rubber Ball

@@gabecordova8025 Thanks