วีดีโอ

Don't forget to get alignment, on factory arms its angle+length, now it's only on the same length as factory arm.

quick trick to install any banjo bolt with new washer, tighten to 50% of required torque, then hammer the bolt on top to seat in new washer, then torque it up to spec. on brake components, especially after u removed washers the contact surface will not be perfect, clean up contact surface and do the trick will avoid 99.9% of fluid leakage

Thank you very much for the video, but I have 9 wires, what should I do for the other wires, including the seat belt please help me with the seat belt wires

Bro I have a question if I take my stock springs out of the rear on a V36 will it lower the car or will it sit the same?

Thank you so much for the video. It's a brilliant idea. If there is an accident, can the airbags still protect drivers and passengers after you bypass airbag lights? Thank you

My sensor is not beside the shifter it is way back & its big with 20 to 30 wires on it what wire to cut. 2004 z

Wait RHD g35 ??!??????

It will be really cool the out come of the bros car good luck with everything

yo bro ive been waiting for this! great to see her go to a home she deserves, this content is great man keep it up, cant wait to see the future videos on the beast

sweet G

Bro I’m looking for that rear lip everywhere man! Lucky to find that

how email ? thanks

I always wonder what this wind would look like if the middle bars were cut out, I wonder if it’d look like the greddy wing thst never made it to production

Engine swap for the sake of humanity

After 3 years of hard work on my truck It looks like the new clutch master cylinders has a 3-6 week brake in period And that's why I keep having to bleed the clutch every couple of days But after about a month it finally started and now I can drive normally.. China parts euggh😢😢y

I have a replica nismo wing. The real one is a lot slimmer all around. The duraflex one looks like the mold was made sloppily from a real one. The real one definitely looks a lot better. (and probably performs better) I wonder if the rocketz replica is any better.

Looks fuckin awesome mannn!!

Car looks great

Thats not a gktech button...they dont go over the oem. You can just easily remove the button like the video explains w/o taking out the center console.

is it worth upgrading to a g37 or keep my g35

car looks clean fr

Bro where you from? You sound like a kiwi?

put plywood under the stand and use a suabru for awd lol

You are the goat bro! You just saved me $150 bucks🤣

Next time your doing it that way on dirt put the wheels on the car and roll the car not the engine hoist.

yall got stuck on the power steering line and messed em up. I did this ... almost messed up the rack. i had to go to the pulga to pull lines off a rack and replaced it. ***Them line from nissan be 300+ $$$

Nice! You should put some shrink wrap on there too ya'll it will protect the resistor better than tape.

I mean if u wanna use my subaru😂😂

Thanks, just did. Just a note to all out there , I’m a 72 yoa did it myself 370Z, 51,000 miles. Good luck

gktech sells them for the 350z not sure if they ship internationally or anyone out of the states and canada

Thank you, that was very useful.

now that the interior of the car is "fixed", do you know how to bypass the impact sensor in case it has been damaged?

Thanks for the tip. This didn't work quite exactly for me. My bolt would go crooked and disengage. What did work was a much larger both and nut. I ground the nut down to the inner diameter of the bushing, thinned it so it would just fit past the end of the bushing, and put a flat on one side to use for the screw driver, and voila, the bushing came right out. And how I have a tool for the next time. There was not enough room for a proper puller. I'm doing it without removing the transmission. I just have the transmission pushed to the side in a Civic.

Please tell us where you got the test pipes from!

Good job 👍👍👍

Just did this on my Z31’s VG30. It’s almost funny how easy this is. Thank you! 🙏

If you do this mod you can go off of the belt part number or get an 08 fx35 belt

What of my g35 pedal it’s hard and also noise on the pedal squeak noise

Nice car

Dude i love these videos. Please keep going <3

Great Video but if the plug has an additional earth/Ground Wire what do you do then?

I have a 07 skyline and have the rca jacks in the middle console, im running my amp to it but it doesnt produce any sound. Any ideas?

It worked! Thank you 💪💪

Jackson Ronald Walker Barbara Clark Patricia

Good info bro

This saved my butt today!

my bolt is bent and rounded its in there tight

Any chance you have the part#'s to uograde the master cylinder and brake booster?

I put the 370z akebonos on my 350z 06 touring (non brembo). and the brake modulation feels barely any different.

Good information, thanks!