- 41
- 180 017
GO-DO-IT-er
United States
เข้าร่วมเมื่อ 20 ส.ค. 2007
Easiest way to Fix Cracked and leaking Torch Hoses.
Easiest way to Fix Cracked and leaking Torch Hoses.
มุมมอง: 3 211
วีดีโอ
Kayaking Prep: Hiking Hidden Trails and a Mostly Dry Feeder. We Found Beavers!
มุมมอง 107ปีที่แล้ว
Kayaking Prep: Hiking Hidden Trails and a Mostly Dry Feeder. We Found Beavers!
Jeep in rednecks with paychecks bounty hole
มุมมอง 64111 ปีที่แล้ว
Jeep in rednecks with paychecks bounty hole
Rednecks with paychecks mud race old but fast
มุมมอง 41611 ปีที่แล้ว
Rednecks with paychecks mud race old but fast
Rednecks with paychecks mud race almost crashes
มุมมอง 33411 ปีที่แล้ว
Rednecks with paychecks mud race almost crashes
Thrill Billy at rednecks with paychecks
มุมมอง 1.1K11 ปีที่แล้ว
Thrill Billy at rednecks with paychecks
Nearly Satisfied at rednecks with paychecks
มุมมอง 38111 ปีที่แล้ว
Nearly Satisfied at rednecks with paychecks
Nice!
Knows nothing about current flow
It will discharge
As a plumber watching you cut across the barbs hurt a little 😅. I dunno about these gas fittings but you do that on a brass pex fitting your definitely getting a drip.
I just use adjustable wrench
Excellent video, thanks for sharing the knowledge. God bless you
I saw someone sayings heat shrink works well but ya i have been using electrical tape on them forever in part to keep it ridgid enough but also because im going to use it on an impact and the pins fly out
The dog “I WOKE UP IN A NEW BUGATTI!”
Yeah buddy 👍👍🇺🇲
Is that black betty?
Nice!😜
Beautiful!
Imm get one soon
"Promosm"
If you want a packer out an extra tool. Just use your razor
A plumber trying to strip wire…..🤦🏼🤷
I have that little $100 handle with a blade sticking out of the end and you can adjust the blade height and it has a spring-loaded clip that goes over the wire keeping pressure on the blade into the plastic of The wire
I will not be doing that. Thank you.
We call that a circumciser
i think there’s a lot to be improved on this. really good tool if you don’t want to knife it out, wish i knew during my apprenticeship. i’d take me twice as long to cut when i was just starting out smh
You freaky made that look hard,,poor advice .
That took way too long
I just score a circle with my knife and then a cut a slice down the end and it pops right off without the extra tools..
Or score it with a knife or razor in 1/8 the time
Yeah 👍
Or just get lineman's since you're working with wire anyhow.1
Oddly satisfying
Ok, i think this is sarcasm and you're the exact opposite. Because those welds beat mine by 10000000 welds
Yeah, it’s sarcasm. All you gotta do is weld more, you’ll get there one day.
Oh hell, I can do worse.. lol
I can do worse also.. lol
Can a fitting be too tight?
Book says 3-4 spins by hand 2-3 by wrench Act accordingly
So this is why I can't take my fittings apart. Lol
Tape than dope
That was pretty impressive and a huge time saver. You must make pretty good on jobs, nice work!
Thanks 👍
That’s never leaking holy cow
Heat shrink....
no shit
🫤
I mean you could just try not putting it on the bolt like a spastic? It normally work for me.
No, next question.
key word is ivy. so no
Leaves of 3 just leave them be
Touch it and find out
No
i always rape mine, but we have harnesstape which doesnt wear om plastics if i have to use it close to cosmetic panels
My ujoint extension still has tape on it from 20 years ago.
You don’t get paid at all do you are you there? Sweeping the floor guy
I did and put grease in a socket to hold the nut for hard to reach areas
In the field we would use 2 crescent wrenches
Stupid as a stupid does