วีดีโอ

The small inverter has Three Mosfet HY1707. I have one the same.

Yes ❤

Fake video N channel MOSFET Inverter pe use hota hai Apne description me dia hai N channel 😅 P channel chahiye 🙏

Pm me

WTG champ. Builds a 100 amp regulated power supply and then demonstrates with something that would barely be using 1 amp. Not to mention, very poor workmanship.

This is stupid doesn't even let u know what the mosfets he's using wtf is wrong with this picture!?! TH-cam is getting worse by the day!!! Smfh

Is that a 9n90c ?

বস আমার ১০ এমপিয়ার চায়না সোলার চার্জ কন্টোলার সার্কিটে হাত দিয়ে ধরলে ডিসপ্লে আসে, হাত ছেড়ে দিলে বন্ধ সমাধান আইডিায় দিলে উপকৃত হতাম

load of rubbish and guessing

Is not pure DC

Can i connect my 10amp pmw solar charger to my car battery so i can charge my sla secondary battery while driving like a Isolator.?

I hope you can afford a microphone for the next video, might give you a thumbs up & subscribe then.

should be tested with some 50 amp equipment.

Form Bangladesh. Thanks

Can i use irf460 mosfets?

P75NF75 ic ki amp baranor jonno bro 🫡

am going to use this exact same controller with a massive 415watt ja solar panel in my next video www.youtube.com/@gatecrasher1970/videos

Mosfet name....

100 amp hahahaha.faker

Fake not 100amp, not 10amp

Not good. 100a cannot be used long term.

What type of diode did you use at the end?

Hello, I will be grateful if you can help me, if we put 2 or 4 igbts of AUIRGPS4067D1 type in the MOSFETs, what will the other required parts be?

Oh god! This is a buffered voltage divider. Not a regular.

I like it, simple straight to the point, no bullshit. 👍

Do you think that the print on the board will withstand such a current?

can this be used to adjust the output voltage of mma stick welder?😅

Any idea how to add current limit

Bonjour je recherche une solution pour abaisser l Amperâge de sortie de batterie 60volt lors de décharge à 5A comment pourrais-je faire ? Merci de votre aide

But still pwm

Is its output short circuit protected?

+1

Its good to test an IGBT, but you cant transfer 5A or 10A! or the IGBT will burn after Overheating, specialy if you have 60V input and 12V output!!! 60-12=48V , 48V*10A= 480Watt that means you produce 480Watt Heat in a 290Watt IGBT, and the Consumer get just 12V*10A = 120Watt :D Use a PWM circuit as a driver for IGBT, Mosfet, SCR ...

I'm watching from Russia. Everything is simple and accessible! Respect to the author! I have two questions for the author. 1. Why do I need a 10-mOhm resistor in this circuit? What does it give? 2. What is a 470 ohm resistor for? Is it possible to do without them and what happens if they are not installed? Can someone else, besides the author, explain in clear language and in detail?! With respect from Russia. \\ Смотрю из России. Всё просто и доступно! Респект автору! У меня два вопроса к автору. 1. Для чего в этой схеме, нужен резистор на 10 мОм? Что это даёт? 2. Для чего нужен резистор на 470 Ом? Можно ли обойтись без них и что будет если их не ставить? Может ещё кто-то, кроме автора, объяснить понятным языком и подробно?! С уважением из России.

You device is a battery kling machine. It is dangerous and worthless.

Electric Tesla your channel is Amazing, keep up the great work..Peace

The circuit diagram is covered by an advertisement for the next film. This is not good for you! Put the drawing in the right place! Another time, think about the reprehensible behavior of the sharer, that he will hide useful details!

What kind of motor is that?? Its bldc or dc motor???

Bom dia, muito bom o projeto, dê referências dos transistores,eu gostei Teresina-Piauí, eu sou rádio amador

What is the function of diode in the output.. please

100A ok ....

There are MUCH better ways of soldering than what you are doing. You are building for a failure. The PCB traces and the screw terminals are not designed for the current you are trying to put through them. Yet another place you are building for a failure.

You do NOT melt the solder with the iron. You heat the parts where they meet until they are hot enough to melt the solder. I saw at least two cold solder joints that WILL cause problems in the future. Good soldering is important if you want the device to last.

Yeah Sir quite impressive for humanity

a beautiful tutorial how to set your house on fire ....

Exellence video, Thanks for sharing and wishing all and thanks so much sir for this knowledge

exellence, Good job and I like the idea

What number of mosfets please?

Pwm

Dont these mosfets need to be isolated from each other on that heatsink?