วีดีโอ

Does your tail lights run all the time the ignition switch is on?

My 6x15 is brand new, board gaps are still wide, no fancy rims. Still the best built trailer for the price on the market and does everything exceptionally well including the powder coated finish

Love you channel! Im putting on the same front & rear lights on my new 2024 Ranger, but I don't have the mounting kit/s for either. Are there kits I should have ordered from Rough country? your thoughts

Rubber tips for walking canes fit over battery post,ratchet strap over fender between wheel rim & fan belt works if you're old,weaker & alone like myself .

Thank you!!

Your full video on this was much easier to follow than the printed instructions. Thanks!

Hey, great video. Thank you very much!

Almond

Thank you so much for this, i have the watch 5 and eas considering the 7 but i think I'll skip this generation, thank you so much

Looks like you have an antenna for the radio. Is that something you added ? My 2023 has a flat one mounted under the front drivers fender and it’s terrible.

Damn it me forever to find a video on exactly what you showed !! Thanks very much !!

Great video - helped me retrieve my 2017 code! Thanks!

Very nice sir!!

Tractor Supply carries the Karavan trailers like this with some upgrades...Just bought one.

You must have the paid version to do this.

😂 great job only 11 likes😢 everyone like his video

Definitely dig this!!!

Do you know of a double bracket to mount 2 pods on each side ?

Nice driving there. I know people are always keeping to the right of those yellow lines but I always say “if it’s paved - go for it.”

Most tow truck drivers have IQs in the low 50s.

My complaint would be the tail gate could use more support so it won’t start bending quickly, floor boards, and no tie downs other than that really nice trailer

Could the light be wired into the reverse light plug that is already hanging there?

Actually got one of these at tractor supply.

How do I make the front camera preview not be mirrored before I take the picture? (Android) I noticed Apple users can do this.

Thanks for the video, I just installed this same mount. Im not sure I would buy this mount again, too many clips broken/missing from my install. Fit was too tight, they should make the bracket a little longer. Will drive a few times and see.

Damn it… special ordered m12 x 50 bolts as per the link listed, drilled doors for them, then found out they’re too big for the M10 holes in the mirrors 🤨

Mine does't have a locking clip.

Good job

Thank you for the awesome video!

Great video. Do you know if you can buy the harness holder for the bus bar wiring seperately?

Thank you 🙏

Is FORScan free? Or is that a paid subscription?

By the way I called Seizmik support today and verified the bolt is an M10-1.5 on this 18081 set of mirrors. FYI!

Where did you purchase the mirrors

Works great, just don't drop it. That plastic likes to shatter instead of dent, then you'll have a big mess

Hello, I bought same WD kit as you for my 2023 and I see that you have the OEM lights that have turn signal built in. Have you since wired straight into the oem headlight?

The factory match is what I'm looking for! Have you tried them? I think I'll have to to buy from OTR it sounds like! Thx for the quick reply

Just got a 2021 Ranger and plan to put on lights. Could you please clarify, I'm a little confused by the L and V style stuff.. Do you know what style the factory switches are? I might just do those to avoid adapters and a like look with the other switches. I saw the factory switches somewhere online and remember they were spendy. Thx great vid and helped me a bunch!

it's the worst design by Ford engineering, Ask them to fix it. 1001 of them say they cant\'t do it

I used white PVC schedule 40 was very brittle and broke up. It was 18 degrees out. Can't find 2" ABS

So the 80 is thicker than the 40. Did it hold up? It seems most people have the best luck with black ABS, or just using a steel pipe. Still working for you?

Get better audio.. you're too far from the mic. Wireless, or wired mic will help

ABS lasts a lot longer.

it would of been nice to actually show how the rails went down fully and with the extra pin option.

Subscribe for full installation video coming soon!

what holds it on? looks like it could slide from side to side? ive seen people using metal pipe ... but they bolt it on... anyway.. good luck to you🤠

Every time I see this mod done I know it's a newbie snowplower. You will get tired of fixing that. Plus it doesn't clean the snow up very well. Once the ground freezes I don't even run the shoes anymore.

Full Install Video here: th-cam.com/video/61gPLMCsKMs/w-d-xo.htmlsi=z5Tkl89fRwy9b-ja

Sorry about the audio, my mic apparently was not working well.

This is not going to last long. You should be using schedule 80 PVC. Also, I used a workmate bench and a 10' length of 2x6 as a fence to cut a perfectly straight line. Your freestyle method will result in a wobbly cut. Good luck!