วีดีโอ

I bought similar mufflers for my street glide from AliExpress they had the fibreglass wrap on them

A lot of people thought the one-way valve will stop the hot water from circulating on the cold water side. Yes, it will after reaching a pre-set temperature. However, the fact that using the cold water (potable) it has some residue hot water within it proves that you will be drinking water from the water heater. Typically hot water tanks have higher contaminates of heavy metal and the leaching within the tank. In essence you will be drinking from the potable water that contains hot water. To completetely isolate that problem you do need dedicated lines on the return so as not to get into the cold side. However, that gets expensive with the additional plumbing.

How do you set the timer?

Very nice installation. Much better than all the drilling and tapping. Plus, I followed someone else's instructions and used braided lines which is way over kill.

Note: for anyone looking for a solid fix, take a look at the Head Hoggers bushing. It's a great design. No, I do not work for them. They are a USA company too!!

I know you followed the directions, but, I’m wondering why it is necessary to drain the hot water heater? Seems like once the water supply is off, and release pressure in the line, you’d be ok to disconnect the line at the hot water heater, and install the pump…. Thoughts?

Harley Davidson. 20th century technology in the 21st century.

Did almost everything the same except I have a M8 114 and I ran hose to atmosphere, not a catch can or filter. Have no issues

I did the same thing I was not able to rethread the grease fitting back on after insertion. What did you end up doing and that would be the thing to show thanks

I have done it without expensive jig tools. There are some good 'close up' videos on YT.

Hot water to brush your teeth?

Thanks, been considering the Jagg cooler for awhile. Will be installing one thanks to you.

Thankyou for this video tutorial! nice work! i will look into it for my roadking special m8 2017. keep the rubber down brother! safe trips...

Did you have a heat trap installed in the anode rod with this recirculating pump?

i planning to do it the same way you do it sir, but it don´t know if it is a good idea that the filter is hanging from the oil lines. Did you had any problems with that issue?

Thank you for showing the actual detailed installation. Exactly what I needed.

After installation of the Watts Hot Water Recirculating Pump,I started using it right away. As long as the pump is running all is fine, but when the pump shuts off I have pipe bumping at the faucet where the bypass valve is installed, when running water in the kitchen. I installed an arrester on the Hot water side at the by pass valve, and still have bumping when running water at the kitchen with the pump off, I turn on the pump and it stops. Should it take an arrester on the cold water too, to stop the bumping?

It looks like it might be a good video, but I'm not goingbto listen with the TV or radio on in the background. Bye.

El termómetro k se conecta adentro de la casa se conecta en cualquiera de los baños o solamente en la cocina gracias

Looks better with the stock cover

Hello Alvaro, Can you please advice how tight I should screw those breather bolts?

Very easy job to alleviate the problem. However, there are cons with this system. Unless your water heater tank is spiffy clean, the potable water that you drink will be mixed with the hot water from the tank. Imagine a homeowner that rarely flushes the tank will be consuming all that crude, sediments, deposits and heavy metal deposits within the cold water system.

Does each sink need a check valve, or just the one that is farthest from the water heater? And also if the recirculatory pump does not have a female swivel adapter on it, but just a male threads out of it...what do you do?

I did this to my Heritage this past summer and I love it,when I took everything apart I looked in the throttle body for oil and other contaminants and it was dry,so for now I’m just running with the breather filter,looks good and she runs like a charm,to answer your question,just keep it the way it is

Wow! I thought I was the only one that had to move my ham before working on my water heater

Open air cleaner looks good but if you get caught in a rain storm , you'll wish you had the cover on it. You'll suck water right into the carb. And that's not good.

to get rid of the clunk, you need to adjust the shifter pawn in the gearbox

hi, where did you get those breather bolts?

This shows real life DIY not the perfect videos the manufactures produce.

Hello I installed one yesterday , went well , owner seems happy with the device his angle stops were reversed at the wall so that caused some confusion but I flipped it around and all is well! Great video!

I discovered when when the unit is on, the valve will initially keep your sink lukewarm, but the plus is if you have a Tushy bidet, that in turn will keep that water line lukewarm also.

He did use Teflon tape to mount the pump. But that is NOT necessary. The pump swivel fitting uses a gasket to seal. And the copper corrugated tube connection swivel also uses a gasket. The gaskets seal the connection. The swivels have straight threads and will not seal anything, even with Teflon tape. It even says it in the instructions " If a gasketed, flexible copper water heater connector is used, pipe dope or Teflon tape is not required."

Truly thanks for sharing. How much roughly has your temperature been reduced by using that JAGG system? 10 or 30 degrees & have you explored riding in 98-105 temperatures yet with that JAGG? Thank you!

Have a 110springer softail. Going to try your idea. Truly love your kindness. Plus just real..very rare now days.

Till it plugs always go up leaves oil in motor an relieves pressure 7/16 hose

Great video, what size of black tubing did you use ?

I like the open filter look. It looks more custom and more powerful(which it is) so show it off.

How do you test that the fan is working?never heard or seen the fan on, on my bike.

Checked mine at 5k and the springs were ready to break,glad i checked

You might try a 1/2 socket, instead of metric, on the Hayden

Nice job ! I just came across your channel in my feed actually. I'm happy to support your efforts and those of other fellow moto content creators. I look forward to seeing and hearing more from you in the future ; keep up the great work and ride safe out there.

run a line down ending by the frame and zip tie it to the frame ,you don't need the filter, crank case pressure should have no restriction .

I don’t like the original covers because everyone talks about heat and with those that’s all they can really do is draw is hot air in

The Teflon tape should have been used before mounting the pump.

The factory cover is ok in cooler weather but the air its pulling in is hot air off the fins

I like your setup there. I will do the same when my shift shaft assembly needs service. Very heavy thick grease would be best for that application.

Great job and nice project...clean your garage🥴🥴

It's nice and all that you replaced the shift lever with new bushings, But then didn't upgrade the shift rod with the crap stock ball joints that wear out and pop off and leave ya stranded!. Ya need to replace those with Heim joints!.

Had to go to another video for better information and every other video says use blue lock tight.

That was very helpful in that I've just replaced the bushings for the second time. As our bikes get older the wear seems to become more prevalent. Thank you for sharing.