วีดีโอ

bro give app link

amazing this has just saved one of my arduinos stuck on a serial flood, nice video well explained

Very simple and usefull instruction, but it didn't work for me. Timeout connection. Then I check few instructions and add one detail. I connect RESET pin to GND for change UNO mode to UART. Now it works perfectly. Thak you very much! Hope this comment will helpfull.

So, most of batteries are fake then 🤣🤣🤣

hi programme pliz

Thanks for this video

thank U so much now its working for my Ardunio Leonardo with CANBUS module and i add this code to the empty sketch #include <SoftwareSerial.h> SoftwareSerial BTSerial(10, 11); // RX | TX void setup() { // Start the hardware serial for debug messages Serial.begin(9600); // Start the software serial for communication with the HC-05 BTSerial.begin(38400); // Default baud rate for HC-05 in AT mode Serial.println("Enter AT commands:"); } void loop() { // Check if there's data from the hardware serial (debug) if (Serial.available()) { String command = Serial.readStringUntil(' '); sendATCommand(command); } // Check if there's data from the HC-05 if (BTSerial.available()) { while (BTSerial.available()) { char c = BTSerial.read(); Serial.write(c); // Show the response on the serial monitor } } } void sendATCommand(String command) { command.trim(); // Remove any accidental leading/trailing whitespace command += " "; // Append CR+LF BTSerial.write(command.c_str()); // Send the command Serial.print("Sent: "); // For debug Serial.print(command); // Show the sent command }

Kya hum directly 12v adaptor to niche Arduino pe jo adapter pin ka port hai uspe lga skte hai ?ya fir apke jesa hi karna padega? Koi difference aaega kya?

Bro can you upload clear picture about code

When try to upload the code it’s showing this message ‘classs Date Time has no member named ‘day Of Week’ . Please answer me. Please answer me.

can share code please

omg tks u so much

Pliss howto tft display eye

Showing I2C devices not found.Help me please

Not true

Do you have ready made kit of this project... If available...I want to buy it Please provide information as soon as possible

i have this error message : #error "Please specify your BLYNK_TEMPLATE_ID and BLYNK_TEMPLATE_NAME" i tried to include it and it doesn't work

Thanks so much

Thanks so much, saved my bricked Nano!

Sir in aim900a i can't get 2g sim what i do where i get 2g sim can it work in 4g sim

What was the WHOLE extra device that was not in the schematic or listed in the annotations.....................................

CLEAN VIDEO MY FRIEND, REGARDS FROM ARGENTINA

Thanks bro😮😊😊😊😊❤❤

Can i ask sir if what is the name of the materials you use in connecting the positive wire and negative wire of gsm module ? I know you mentioned that you need a 5v DC power supply adaptor for gsm module...But what I want is the material you used between the positive wire and negative wire of the GSM module...

Hi, I want to make like this but a washing machine alarm system with sms alert. How to do it?

hello brother , please share links for hardware

thank you

sir i connected my gsm 900A module to 12v2A power supply but in my gsm module only DC power light is not status and network what does it mean mera gsm module khrab hai kya please tell or mene vodaphone SIM vagera pehle se hi dala rkhi hai valid rechage plan but firr bhi nhi jalri light

thx man :) you just made my day

I just need to change the contrast with a screw driver. Thank you.

Can we use Arduino onu...?

Full ok 👍🏾 ayii Time out vakan parumo Replay 🙏 🙏 🙏 🙏 🙏 🙏 🙏 🙏

In my case ... I am using the I2C module with 2×16 LCD Display ... But the inside blue light is not working

Sir can you teach the code??

is there a reason why you used A4988 instead drv8825?

link is not working

thanks sir🙏 it is working

What is the composition of your lead?

If i power up Arduino with 12V 2A. I think no need to give, power for shield, i think?

I'm not doing anything, why do you keep asking?

The code is having error

Hi sir

Bro app link pls

bro send the circuit diagram

Can you share the code bro. Please.

Hey bro Bluetooth terminal is getting connected but messages are not displayed on LCD ..Please reply

it still shows me err3, why?

I was missing the short circuit of the 2 extra pins. Damn... thank you so much!

#include <SoftwareSerial.h> SoftwareSerial bluetooth(2, 3); // RX, TX pins for Bluetooth module int relayPin = 7; // Pin connected to the relay module void setup() { pinMode(relayPin, OUTPUT); digitalWrite(relayPin, LOW); // Ensure relay is initially off Serial.begin(9600); bluetooth.begin(9600); } void loop() { if (bluetooth.available()) { char command = bluetooth.read(); if (command == '1') { digitalWrite(relayPin, HIGH); // Turn on the light Serial.println("Light is ON"); } else if (command == '0') { digitalWrite(relayPin, LOW); // Turn off the light Serial.println("Light is OFF"); } } }

@hossenalatish38 قبل 0 ثانية Hello my friend Can you help me to program a microcontroller chip ?