วีดีโอ

I have not officially checked the range but.... I can be in my second floor bedroom and still connect to it in the garage and that is at least 20 meters through walls. I hope that helps. I may have to make a video on that. Thanks for the idea!

@ You’re welcome! They have a new version coming out this month Smart Shunt IP65 300A which is waterproof and slightly cheaper than the 500A version. This version has M8 bolts versus M10 on the 500a and should not need to cut wirings to place larger eyelets to fit. Have a good 2025!

Voy buscar el debujo que hice de mi cable. Se quieres mandarme tu correo electronico? philfry1964@gmail.com.

tambien... Mira este video: th-cam.com/video/g7HYvDdBXHY/w-d-xo.html

Thanks! I hope to be back out there soon!

Can you send me a photo of the sensors? philfry1964@gmail.com

These days I can’t disassemble them, the only thing I have are the codes 872066 872068 3852029 It gives me this three codes in the engine exploded, but I don’t understand the last 2 I have to put and if they are needed

Ok... 872066 = Temperature Sensor 872068 = Temperature Sensor 3852029 = Temperature Sensor They are all three temp sensors. I remember that my exhaust elbow temp sensor was broke off and I had to replace it. Part Number (3862500). I don't think my boat even looks at the exhaust temp anyway. I would only think that your motor has the Water Temp Sensor and the Exhaust Elbow Temp Sensor. I doubt that you would have three sensors. If you google search the part numbers you can see that two of the sensors are for a screw on nuts and one is for a slip on wire lug. My Engine had only the two sensors.

Muchas Gracias! Que bueno que mis videos podría ayudarte! Cuando yo estaba haciéndolos tuve muchas dudas... jajajajaja Saludos!!

Thanks! I have to work on that part for sure!

@@PhilFryOutdoors The feeder Block Box turned out great, now I just need to get the deer to eat the blocks 🙂

Oh, I did.... eventually 😂

Sorry for the late reply... Manifold is 20-25 ft lbs and the exhaust elbow is 12-14 ft lbs.

Hi! I think I had around 3k invested in it. It took me about 40 hrs of labor but that's because I was going at it pretty slow. 😂😂 I wish I was in the position to do another because it was fun but I have many projects backed up that I need to complete. If you need a good machine shop referral in the Atlanta area I can suggest a good one.

It could be that the carb is dirty and playing havic with your idle mixture. Some of the carbs come with a cap over the idle mixture screw that you have to pop off. Apparently the EPA doesn't want us playing with it... LOL. Also, you may want to take a gander at your automatic choke and maybe your fuel as a long shot. I am kinda leaning towards that dirty carb however. Hope this helps!

@@PhilFryOutdoors thanks Phil! would you think the carb cleaner can could work or recommend taking it apart and clean it?

@@tomexplorador855 You can try the easy route first and then if that fails tear it apart and put a kit in it.

I just have one going through the yak power and no problems... The other has it's own battery.

Thanks!

Let me see if I have pictures or some video of it. Did you install the gaskets along with the restrictor? I have a drawing that shows how they are placed. If you email me I can send it to you: philfry1964@gmail.com

This is directly from Victron: community.victronenergy.com/questions/59286/smartshunt-installation.html Let me know how it works out, I am curious too!

Darn... sorry about that! I think what happened was I got behind on time and had a bad case of "get her done".

I was pretty worried about the oil pan for sure! Funny thing is that I had an oil leak when I ran it.... turned out it was just where I had the test oil pressure gauge screwed in. 😂

My machine shop acquired them for me but I think you can get a kit through Michigan Motorz.. One thing to keep in mind is the clearance on the crank journal for the connecting rods. It seems that some rods are a fraction wider at the crank and can cause wear and friction on the edges of the journal which can cause a failure like a spun bearing for example. My machine shop had to modify my journal width ever so slightly to prevent that.

Thanks!

Is that what the machine shop says? If it was me, since something has to be done anyway right... can't use that engine with the cooling all blocked off.... I would disassemble it, try and assess just how bad the cooling jackets are and determine if it's worth the machine shop trying to dip it and clean it out. If you had them dip it and clean it and it's too bad off, then you are just out the cost of dipping/cleaning. If it's so eaten up that the walls are too thin then I would look at getting at least short block or and new engine from someplace like Michigan Motorz.

Wonderful!

Thanks! Honestly, I think I got mine at Harbor Freight, but these would work well depending on the size of your project. amzn.to/42zwJBg

You are right! I should have mentioned that.

Si, Yo piense en eso pero yo recuerdo que antes cuando hice eso no tuve mucho cambio en mis Estadísticas. También ahora existe subtitulados... pero voy hacer más en el futuro.

LOL! Good Point! I should do that!😆

Yeah, trying to work it in between work and life stuff! LOL!

Thanks! Good luck with your build! Be sure to send pictures!

I think the steam is the real secret in this. If you can produce more steam the better and possibly like you suggest adding some more heat.

So, on the fish finder cable, on end has a screw connector for the fish finder and the other end you have to either directly wire it to a terminal or you can put your own end on it depending on what your power source requires. I am using the Yak-Power system and all I did was install the plug, ( amzn.to/4aEcN3O ) on the other end.

So far it hasn't been a problem. However, I fish on lakes and have only been in rough waters very few times. Even in rough water when everything was wet and with rain, I had no problem. It has a rubber cover if it gets too rough I wouldn't use that port I guess

😂

I bet a cell phone and alcohol had something to do with it.

@@PhilFryOutdoors was there a car?? I couldn’t see that 😱

Yup... crashed into the tree

So who keeps on driving past..?!

@moniquemannaert3468 I understand but it's not exactly a good area and there were about 4 stopped on the side road.

I may just do that... I am ambidextrous but cast mainly with my right arm.

When I return from traveling, I will send you a diagram.

Sorry for the late reply. I didn't make a video on the 2nd power pole install because Casey Reed has a really good video out there on his channel. Check it out here: th-cam.com/video/LBhuEE7hOwk/w-d-xo.html

Thanks!!!!

How l contacto you

@@luispisquiy9001 You can email me at philfry1964@gmail.com.