วีดีโอ

You had called if you were back in New Jersey where are you Lasvegas?😅

Looks like a Honda 3.5 L engine, which are known to be male re-quo employ, stripped out by lube techs. He probably had this installed as to not replace the oil pan which is expensive on that motor and to make your life a little easier. Might take a few minutes, but you wont get in trouble for messing it up

I've installed Valvomax oil drain valves on two of my cars and it's been great to not be getting oil on myself or on the driveway after every oil change. I considered the Fumoto valves but at the time their website was out of stock of the model I needed.

I wouldn't accept those, period. 45 min drive for an 8 dollar order with tip. No.

I've been using Futomo oil drain valves for 25 years. Takes about 10 minutes to fully drain 7qts out of my V8s. Warm up your engine. Remove the oil cap. The oil flows right out rather quickly.

maybe hes tired of assholes like you that strip the bolt or locktite it on there.

Also you should take the cap of the oil under the hood lol

When you take your vehicle to a service shop you are giving them legal permission to damage it. This eliminates some of the possibilities.

Okay, now open the valve ALL the way. Nice try though

Cause its cleaner.

Drain bolt works just fine, lol. You do it a few times and learn not to make a mess. Not hard. But to each their own. Your vehicle🤷‍♂️

Why did you replace the filter while there’s still nasty old oil draining from the motor? Maybe it’s just me, but I wait until the oil is done draining before I install the new filter just on the off chance old oil could contaminate the new filter. And like someone else said, why not inspect the rest of the vehicle while you wait for it to drain? You’re missing out on potential work that the customer didn’t even know they needed. Just my 2¢

Bro shut up i use that shit on 10 gallon oil pans on trucks they drain fast asf you a click bait for views

I agree, those fu motos SUCK! If u bottom out, & snap that off??? 🤔🙄

Hmm was the car warmed up? Did you loosen the fill cap or pull the dipstick up? Most "techs" are computer smart/common sense stupid.

These are nice to have on fleet vehicles that require frequent maintenance. I’ve installed on people’s personal cars by request. Work great

There is a good reason the factory doesn’t put petcocks on oil drains, you might find out why.😂”hint” vibration …

I don't know what's worse that drain plug or having the drain bolt labeled on the bottom of the pan... Mike, I'll tell dumb people are these days though. Even the young mechanics need a f****** label going to the drain plug.... Remember the Subaru Simon drive event signed and drive well. Let's just say they used to do that on those commercials. Oh, sign then drive. All you need is your license blah blah blah and then now when that commercial comes on at the end it says in reality you will need more than your signature and license. That's the world we're living in that you have to have a oil drain plug labeled and commercials have to say at the end in reality. XYZ

And did you happen to warm the enjun? That oil looks awful thick

Blow air into valve cover genius

It’s great for ppl who do their own oil.

If you're a lube tech it's because of idiots like that that over torque the bolt

I would cancel that so fast !

cockamamie bulshit hit a diaper in a road and oil spills out. Nerd

Those things always make me laugh. Its a solution to a problem that doesnt exist 😂😂😂

Your showing your youth or inexperience or maybe both. Those fumoto valves have been installed on hundreds of thousands of semi trucks, tractors and stationary equipment longer than you have been alive.

Lies. I have Fumoto valves on all 3 of my vehicles and none take more than a few minutes to drain.

It's easier to drink from the tap of the Fumoto drains. Used motor oil pairs nicely with crayons with paste for desert.

Looks like a v6 Honda their all generally 17mm not that hard plus imagine it just opens up while driving or your unaware, just making it over complicated for no reason 🤦🏽‍♂️

GET YOUR PLUG HOLE STRIPPED OUT BY A DUMMY OIL GUY AND YOU'LL LEARN SOMETHING BUD

“Does his own services” then why is he here for an oil change

😂

😂 guy must be a rocket scientist cause this is reeeal smart 😂

I already spilt a half gallon of oil down the side of your motor while changing the oil filter.

Yes...a protectant like 303 Aerospace protectant.....but not silicone. Residual silicone can affect a host of engine sensors and systems....and heaven forbid....talk to a body shop......they will tell you don't spray silicone within miles of a body shop if you want to ruin on-going paint jobs....

That looks like it’s off of an old Kohler generator. It would either be a Ford, Hercules or a Cummins engine. Maybe even an IH… They have that same style drain valve. My hesitation with this would be fear of road debris shearing that off or accidentally opening it..

Depends on how hard it is for the shop to Not strip out the threads…he’ll I’ve had to get a shop to replace my damn dip stick because they broke it off being stupid or somethin

I install them on my trucks. I have to do oil changes every 2-3mth. Sure it takes awhile to drain but its really clean to do one. On my valves i can hook up a tube and drain directly into an empty oil jug. It also allows for a oil sample to be taken mess free. Easy peazy in your driveway. While its draining im doing things up top like changing the air filter, checking belts etc. Im sure it sucks for the 10min lube places. But for those doing a proper maintence doesnt notice any extra time that it takes to drain.

I supposed to be done 🔥

You should be inspecting all the car in that 10 minutes, instead of bitching wile you are saving the oil pan threads and no gasket to leak There wonderful.

Get air coming in from the top& it’ll flow better..😂

You’re supposed to change oil in the engine is hot anyway

Take the oil fill cap off.

It looks like somebody filled the oil up to the valve covers. When it pours out the PCV valve it's full.

FFS man. Could you be anymore cringe? OPEN THE VALVE ALL THE WAY! As a kid, how short was your school bus?

I want to put that on my e60. To remove that bolt on an e60 n62, It takes a lot of strength and torque to remove it.

With or without the valve, it was not going to drain any faster . did you at least heat up the engine that looks like cold oil?

There would not be a need for if not for the bad mechanics that either leave it loose or tighten it so much they damage the pan plug or gasket. The dude cares about his car. Just work with him. This is a sign of the times we are in. Looks like you have a covered clean work environment. You have your gloves on. A nice oil drain pan. A lift so that it is convenient to work under. Just wipe the oil off the car from the filter change and carry on. Not saying you were the bad mechanic.

No he put that on because he goes to jiffy lube to get it done

People do that because many mechanics now just wear the patch. And when they damage the plug they blame the last one. 😂😂😂😂😂😂