SATHISHKUMAR SARAVANAN
SATHISHKUMAR SARAVANAN
  • 5
  • 14 595
Sheet Metal Part 1
This model is a first exercise in Creo Sheet metal and In this video, In just do the reverse engineering concept only. I don't design this with exact dimensions. I just relatively take the dimension as per my choice. I hope you must like this and kindly do support my channel.
มุมมอง: 34

วีดีโอ

Helical Tube Using PTC Creo
มุมมอง 1474 ปีที่แล้ว
Helical tubes are mostly used in heat exchangers, and it is also modeled for that. Watch the full video and hit a like and share. Don't forget to subscribe.
Pipe Stress Analysis Using Ansys
มุมมอง 14K4 ปีที่แล้ว
Here, a pipe stress analysis with the help of Ansys. In the analysis, I've shown all the data for analysis, including deformation, von misses stress and strain. Kindly watch, like and share.
Five basic commands of PTC Creo in modelling
มุมมอง 1164 ปีที่แล้ว
Dear, friends There is today's video, about five basic commands in creo while using in modeling or creating a part. In, this video. When you are creating a revolve and helical sweep, there's centerline that is a must to create it. I hope this will help you as much and keep supporting my channel for more videos and kindly share with your belongings, who will need this.
Structural Analysis Of Rectangular Bar
มุมมอง 1934 ปีที่แล้ว
Dear, friends Here, structural analysis of rectangular bar with calculated values of stress and strain. Software Used: PTC Creo 4.0 and Ansys 16

ความคิดเห็น

  • @PreethiPreethiNaveen-fz6dc
    @PreethiPreethiNaveen-fz6dc 6 หลายเดือนก่อน

    Bye

  • @PreethiPreethiNaveen-fz6dc
    @PreethiPreethiNaveen-fz6dc 6 หลายเดือนก่อน

    Hii

  • @PreethiPreethiNaveen-fz6dc
    @PreethiPreethiNaveen-fz6dc 6 หลายเดือนก่อน

    Hii

  • @alializadeh8195
    @alializadeh8195 2 ปีที่แล้ว

    مرسی

  • @alializadeh8195
    @alializadeh8195 2 ปีที่แล้ว

    Thanx

  • @bintarabarkah36
    @bintarabarkah36 3 ปีที่แล้ว

    Hi bro, what is the title of this backsound?

  • @daffaramadhananwar2690
    @daffaramadhananwar2690 4 ปีที่แล้ว

    Hello sir, thanks for the video, and im still learning using ansys. if youre not bussy can u make an analysis "crack in outside pipe due to internal pressure" using ansys please? because i want to learn it so bad. ill really appreciate if you help me, and thanks sir you do the good job for making this video.

  • @bondotea4699
    @bondotea4699 4 ปีที่แล้ว

    Hello Sir, thanks a lot for the video, please, l have a specific problem with [ The None Linear Analysis of Steel/Stainless Steel Concrete Filled Tubes under axial compression ], l have tried several times, but still failed to get the correct data for the analysis, including the deformation, von misses Stress, Strain and all the Deformation curves, so l will really appreciate any help or any possible videos link, once again, thanks a lot for the good job you are doing

    • @sathishkumarsaravanan1721
      @sathishkumarsaravanan1721 4 ปีที่แล้ว

      Thanks, good to hear you. Then, on what step you're facing this issue. I mean ( Engineering data, geometry or Meshing and final solution ). Because if any material parameters will not in there. It's shown like that. Or In case if you're not choose correct loading point, faces or nodes. It'll be appear.

    • @bondotea4699
      @bondotea4699 4 ปีที่แล้ว

      l don't think l have any issues with the ( Engineering data, geometry or Meshing ), but the final solution and that's what i don't understand

  • @parthasarathi7823
    @parthasarathi7823 4 ปีที่แล้ว

    Gd

  • @actiondudes007
    @actiondudes007 4 ปีที่แล้ว

    Vera level bro

  • @prakashtech5161
    @prakashtech5161 4 ปีที่แล้ว

    Good luck 👍 .. put audio

  • @manimegalaimanimegalai9211
    @manimegalaimanimegalai9211 4 ปีที่แล้ว

    Very good da

  • @dharunshanjais4485
    @dharunshanjais4485 4 ปีที่แล้ว

    Supper bro