We lost power in our electrical panel. Afterwards the washer blinks the sensing light, puts a shot of water in then nothing. Then starts it all over again. Have tried all of the unplug, closing door 6 times tricks and still not working. Lock light is also not coming on.
I reset it got to the blinking lights , then went right to the rinse light then hit start and nothing happens does that means it didn’t reset because this damn washer gets off balance if I put 2 towels in it , and it literally sounds like a damn tornado it’s horrible and I’m on the 3rd floor my neighbors must hate me😮
Make sure your water lines are turned all the way on. Make sure your drain hose elevates at least thirty inches above the discharge hole. Make sure your washer is level.
My washer was stuck on spin light blinking.I try the reset mode combination and nothing,then I unplugged and plugged back holding the start button and it got it out of that error
Cycle shifter. Just changed mine. Same noise. If you clear the fault light it will do it again. Theres a great video to help you on TH-cam. Its easy to change. .I think that's your problem.
Maytag Bravos model MVWX655DW1 I had a sensing problem I thought but just got it checked tonight and my problem was my wash temperature dial. Not the dial itself but the setting. The tech told me that the newer model washer should be hooked up with both hot and cold and hot water hoses in the back of the washer if you want it to run on cold water setting. It still uses a bit of hot water not much just enough to regulate the water temperature. If it's too cold and you don't have the hot water hose hooked up it still senses for hot water and that's why it looks like it's stuck on sensing. No parts needed except the steal hose for the hot water. If you want to run strictly cold water set your temperature dial to tap water and it will work. Hope this helps. My Maytag is 7yrs old.
Today I received the cold and hot water inlet valve assembly. While taking off the old one I noticed the casing around the cold water inlet valve was cracked a little bit. After installation, I started a normal wash and it is working properly now. So glad that fixed the washer. I messed up and paid more for the part, I didn't know that they changed/replaced the part number for the cold water inlet valve when searching for it online. Didn't find out until after purchasing. Paid a total of $62 with expedited shipping. Found it right after ordering for $26 on Amazon. Part number for cold water inlet valve is w10868381 has now been replaced by part number w11210459. Just in case anyone else does the same thing as I did. I ordered the part yesterday and got it today. Quick shipping, even though I paid extra for it. Got here fast.
When I do the clean washing machine mode everything works. It spins, drains, does everything. But when I do a normal wash it stays stuck on sensing. I think it's the cold water valve. Checked the hot and cold water sensor and got nothing from the cold water valve.
Pull the tech sheet for the unit (inside the console or taped to the inner cabinet) and follow instructions for testing the motor fault. Most likely a bad CCU
Mine wouldn't as well. Tested the hot and cold water inlet valves. The hot water valve was fine but the cold water was bad. It would wash but stop at rinse because rinse uses cold water. Replaced it and now it's working properly.
The water valve sensors need to be changed.
Help me
We lost power in our electrical panel. Afterwards the washer blinks the sensing light, puts a shot of water in then nothing. Then starts it all over again. Have tried all of the unplug, closing door 6 times tricks and still not working. Lock light is also not coming on.
I reset it got to the blinking lights , then went right to the rinse light then hit start and nothing happens does that means it didn’t reset because this damn washer gets off balance if I put 2 towels in it , and it literally sounds like a damn tornado it’s horrible and I’m on the 3rd floor my neighbors must hate me😮
What was the issue? Shift actuator or water valve?
I had the same problem, replaced shifter actuator,fixed the problem.
Lol😂😂😂😂😂
Jerk, I wasted this time thinking you would show us how to fix it
I clicked on here I thought you might know you know say thing I do nothing stupid video I can make one like this dumbass
Make sure your water lines are turned all the way on. Make sure your drain hose elevates at least thirty inches above the discharge hole. Make sure your washer is level.
Turn water on
My washer was stuck on spin light blinking.I try the reset mode combination and nothing,then I unplugged and plugged back holding the start button and it got it out of that error
There is a manual in the cab, try recalibrate.
soooooooo…..
Having the same issue.
Try clear out the water pump. And reset the washer after. It works for me
Sounds like a bad capacitor
The clicking sound at the start of the water sensing, is it suppose to click when its filling water ???
Have the same washer and the water doesn't fill😭
I have the exact same washer
It ain’t got no gas in it😂😂
We are all messed up with this kind of machine😂
How obout no sensor lights just humming sound
I’m looking for helpful videos 🙄🙄
Junk I hate those things
Shift Actuator
Cycle shifter. Just changed mine. Same noise. If you clear the fault light it will do it again. Theres a great video to help you on TH-cam. Its easy to change. .I think that's your problem.
I cant seem to get the lock to stay on for it to start washing how can i fix it
Bad sensoy
Mode shifter
Maytag Bravos model MVWX655DW1 I had a sensing problem I thought but just got it checked tonight and my problem was my wash temperature dial. Not the dial itself but the setting. The tech told me that the newer model washer should be hooked up with both hot and cold and hot water hoses in the back of the washer if you want it to run on cold water setting. It still uses a bit of hot water not much just enough to regulate the water temperature. If it's too cold and you don't have the hot water hose hooked up it still senses for hot water and that's why it looks like it's stuck on sensing. No parts needed except the steal hose for the hot water. If you want to run strictly cold water set your temperature dial to tap water and it will work. Hope this helps. My Maytag is 7yrs old.
What if it won’t pass wash mode
Today I received the cold and hot water inlet valve assembly. While taking off the old one I noticed the casing around the cold water inlet valve was cracked a little bit. After installation, I started a normal wash and it is working properly now. So glad that fixed the washer. I messed up and paid more for the part, I didn't know that they changed/replaced the part number for the cold water inlet valve when searching for it online. Didn't find out until after purchasing. Paid a total of $62 with expedited shipping. Found it right after ordering for $26 on Amazon. Part number for cold water inlet valve is w10868381 has now been replaced by part number w11210459. Just in case anyone else does the same thing as I did. I ordered the part yesterday and got it today. Quick shipping, even though I paid extra for it. Got here fast.
My washer locked and I tried the reset but still not opening
When I do the clean washing machine mode everything works. It spins, drains, does everything. But when I do a normal wash it stays stuck on sensing. I think it's the cold water valve. Checked the hot and cold water sensor and got nothing from the cold water valve.
Have you found a solution my machine makes A horrible sound its not even a month old
Pull the tech sheet for the unit (inside the console or taped to the inner cabinet) and follow instructions for testing the motor fault. Most likely a bad CCU
Okk
You got a bad burn you have to change
Just buy a regular washer problem solved,all this extra digital stuff ,cost more money
My is not rinsing and spinning
Mine wouldn't as well. Tested the hot and cold water inlet valves. The hot water valve was fine but the cold water was bad. It would wash but stop at rinse because rinse uses cold water. Replaced it and now it's working properly.
👀UGH❤
Como hacer todos los ciclos?
Lid switch has an issue
Mine have the lights yellow not green 😅
Damn, and this is a simple washer and still having issues
Ahhaa😊
Buy new one
Mine spins, does hot and cold, and all of that but does not lock during sensing and also keeps trying to fill idk man.
did you find the problem? thanks
@@percyflores7517 wiring harness… unfortunately a special order too so its gonna be a bit before i can repair. Just got it too :(
I thought you had the answer 😭😭😭😭
On my kenmore he washer 500 it’s starts to fill & stops