วีดีโอ

Wow I own a 2017 blk fiesta ST and my wife drives a 2019 edge ST 🤣🤣🤣🤣🤣

Was your friend able to move the shifter into 3rd and 4th and the car acted as if still in neutral? Having a similar issue with 1st and 2nd. Goes does fine everywhere else.

This video doesn't mention that the new sensor needs to be calibrated, most likely by a mechanic unless you have the diagnostic tools. I found this out when I replaced my sensor but found that the brake lights were on when the pedal was not depressed and vice versa.

Got the 2 little ones on the sides but the main plastic bit im struggling to get off to get to the inner bolts

Actually, a Focus DCT transmission. I think I found it...a seal kit with all seals, the CV shafts bearing saddle brackets and the clutch retaining clips.

On the DCT transmission.

Does anyone have the Ford part numbers for the inner and outer input shaft seals?

how can i make my backlight brighter because during the day it's not even visible and at night it's barely noticeable😢

bless your soul dude, was looking for a way to wire it in my se, rs probably looks better than my se lol, but i hate how they only have one on the drivers side, i was thinking about putting it into the arm rest becase there is a 12v charger in there, maybe ill still consider it but this helps alot in the case it doesnt work!

Thank you, the exact same thing happened to me with seeing a spark. This video fixed my problem.

Thanks for the video. I can’t wait to swear at my wife’s car. But you make it easier for me to break down the steps.

😅😅😅😊

how many miles did this have at the time of recording?

worked. thanks mat

Absolutely amazing. Just followed this video and was able to correct the issues with my 2008 Acadia. All for a $10 part this is even linked here. Fantastic job @gapperformance!

Hey I know this is a very old upload but you mention you changed a hex digit to 0, which line and which number digit did you change? I've been through the forums and all the posts are for themes, air climate control and the double honk. I just want to upgrade my speaker sir

On the Equinox 17 that little bolt is right next to freaking panel I don’t even know how to remove it

Thanks for the video, made it easy. Mine's a 2017 and i didn't realize it doesn't have that hose going down the front by the radiator until i got the old one out and put the new one in. They must have changed it in the later years. Now I've got to send all this back again and try to find the right part for the 2nd time lol.

I have a pig mix he's a complete maniac.

I’m replacing the CV Axle on the passenger side of a 2014 Ford Fusion, would I have too still drain the transmission fluid, before removing the CV Axle on the passenger side ??

Thanks to you it worked and I so appreciate you having this information available. Once again thank you

Lol stupid neighbor it's a free country

Thanks

Whats the tool called

You're a lifesaver! That thing was driving me crazy! Thanks for the video!

I have to go and check the codes on my 2011 Acadia tomorrow (just worked a 12 hr shift so didn't make it today) but fingers crossed this is the issue! Thanks in advance either way

I ❤ Pugs! 🐾

how you got that radio system in the mk7? looking for that for a while now

very interesting

I replaced the sensor and didn't resolve my problem doesn't true

Thank you so much!!

THANK YOU! I want to disable all of these cameras and tech.

After installing the downpipe again with the defouler on, would you recommend getting the straight or j style defouler for ease of installation? I wasn't sure if there was any clearence issues with either so I just wanted to make sure.

Hello. At 4:11, those bearings, I think mine are worn and that my axle is making noise in there. Is it pretty easy to pull those apart and check without doing anything else?

Could you leave a link to all the tools

It's honestly easier to just drop the whole strut from the top. In any case, once the axle is in, it's a pain in the ass to get the knuckle lined up with the strut. Fucking fwd 🙄

Saved my ass too! Thanks so much for the tip

Great video help me fix my power steering issue

Thank you for this video

This just happened to me and my friggin´ heart stopped. For what it´s worth, I first threw in a gob of wax from a chapstick into the hole. This way if any shavings are generated they will stick in the threaded ID and not fall into the cylinder. I then took a large flat head screwdriver and knife-edged both sides to engage counter-clockwise. I applied light pressure so the edges would dig in and it came out easily. In the event anything worked its way into the cylinder I connected a plastic tube to my vacuum cleaner and snaked it into the cylinder (after removing the broken threads of course) and rotated to engine a smidge to ensure valves were open. This way the vacuum would create turbulence and flow that would hopefully suck up any potential material that worked it´s way in. After a few minutes of this I added a new spark plug and tested the bike. Everything looks good, fingers crossed. Good luck guys.

Saw future videos....can Confirm on the tape lol "Wow even I lied about the tape" 😂😂😂😂😂😂 Temp fix = Perm Fix Lyfe!! (My Universal CV Axle boot is still superglued to my axle.....I get it !) Tks for the vid guys! Also: Rain concerns?

bug guards makes cat eyes and most old chevy trucks look 100 times better

did it make any kind of weird noise when these were bad ?

Hi there, slightly odd sounding question but do you sit alot lower in the non-recoros? I find I’m sat way too high in the standard ST seats. Cheers

Two of my quick connects snapped taking mine apart. All to find out you cannot access the backup camera this way. Fucking ford, man.

Do you have the link for 2013 fiesta SE model cuz mine are leaking bad and i want to replace em

Hey man so I changed the Solenoid and I’m still getting varied and extended crank times. Is that the issue you were having as well? Just trying to troubleshoot.

Do you have the part number for thisnor site i can get from?

I got my windscreen replaced and I'm pretty sure the guy who did it put them on backwards after watching this video. Would I need to recalibrate etc or just swap them out? Appreciate the video its been driving my crazy

What a legend, thank you for posting this!