วีดีโอ

Hey bro im about to go this way on my S63 x5m. So far any positive or negative feedbacks on your system. Hope you’ve been able to catch some oil?

I don't think you needed those metal ends

I try to post links on where to get all this stuff for less and better, but TH-cam deletes my comments if i put links in it, look at my Youtrube profile and send me an email, and I'll send you the details. You need to smooth the entire fittings with the dremel as shown. Do not cut it shorter. Wrap electrical tape in the direction of how you screw on the fittings. Put a o ring inside the fitting that’s about the size of the inner fitting. Put it all together. It will be wait tight and don’t overtighten. Just to when the sitting doesn’t rattle or move on it’s own. Test blow into an end and close the other end with ur finger. If it’s air tight. You will be good to go.

Do not cut the 1st rib of plastic, it will not leave enough for the AN Fitting to fit flush, and it will leak, if the fitting rattles, it will leak, you can do a test with blowing into it and covering the other end with your finger, if you can hear air, its leaking and you will get a check engine on lost pressure. I had to buy a new set of PCV valves to redo this cause i cut the 1st rib off of the plastic, do not do this.. I keep trying to post where to get all the right parts but it keeps getting deleted. You can get all the parts cheaper on amazon and ebay now, including using AN Fittings instead of the hose clamps on the catch cans to make it look really nice. but you have to make sure you do not have any leaks in the lines, or you will get a check engine light. Put a O ring inside the AN fittings on the plastic pieces, and do not cut the 1st ribb off, just sand them down and thread them on the fittings. I tried to post links to all this but you can get a good set of everything on Amazon and 150 degree fittings on eBay for much less than the posted places, do your research.

I keep trying to post the details of this correct install, it keeps getting deleted. You should not follow this, the lines will leak and throw a check engine, you need to make changes. Contact me for links to the setup to make it without hose clamps and a real professional setup that is air tight.

Can this be done on n63TU cars or just non tu?

Does it help to be running jb4 with these catch cans I seem to be getting a code (#107001) after install (throttle valve angle intake manifold pressure 2)

So I did the same process and I couldn't get my car to stop smoking. As soon as I removed and put back stock it stopped smoking. Did you have any issue like that?

I’m thinking of doing this but don’t like the prospect of having to dremel and cut those connections. Have you or anyone found a a solution to straight connecting it?

good job, nice video. thanks for posting

Were the mufflers direct fit or some extra modifications were done to make them fit ?

How you doin man. Have you don’t your valve seals in your ownership yet

How much inches did you cut the braided hose to for your catch cans?

Is it really impossible to install the catch can with the oem intake? Just recently got my 2021 XB7 Alpina, and there aren’t many parts out for me to upgrade as of now. I’ve purchased VRSF downpipe, and mishimoto oil cans for it but couldn’t find charge pipe for the ride

What’s the quarter mile on that car

PK, there's another video of someone emptying their catch can after a month and there was a lot of water that it caught. What are you seeing?

Where did you get that top brace?

Here is my 2008 Nissan Sentra oil catch can configuration and the end-product result. 04m37s ~ 05m04s discolored gasoline sludge and carbon residues safely trapped in engine oil catch can oil catch tank th-cam.com/video/xCfhebKMRbU/w-d-xo.html 오일 캐치캔 캐치탱크 장착했습니다. 가솔린 휘발유 차량이고 포집된 기름 상태 찐득찐득합니다. 2014 Hyundai Tucson SUV oil catch can end result th-cam.com/video/2wvupPKUeTE/w-d-xo.html 자동차 엔진 수명 연장... 집에서 일반인 누구나 DIY 가능 최소비용 최대가성비 The most cost-effective engine DIY maintenance at home th-cam.com/video/6DLn0kIi-84/w-d-xo.html

You got downpipes and resonators? It’s very quiet

What year is your 550? And how much miles?

PK The Silcone U Tube linked from Spitt Mods does not look like the one pictured. I would really appreciate if you could confirm the dimensions as he has not responded to my ? for a few weeks now. Thank you!

Hey PK, I have purchased everything for Oil Catch Cans and CAI. The only thing I am unsure about before eI tackle this project is the U Hose. The one I receveid seems too large. Could please confirm if is the correct size? Thank you so much!! 3' 76mm Center to center Distance 7.5 (190mm) Leg length 4.72.

Can you please tell me what size what the Carbon fiber Tubes were for CAI? 2.5' ??? Thanks

Why not fit the hose right onto the pieces instead of cutting them off ?

Thank you alot for this video i have long time waiting for install my Catch can and finally find the perfect setup for my 550i👏🏽💪🏽

What year/model is your car & engine combo? This looks like a 2011-13 N63 (non-TU), is that correct?

?? How is your cold air intake in the rain??

Nice video I stumbled on. I also watched splitmod but didnt execute cai. Maybe some day. Did have catch cans sitting around. Since ur video this is my next project. Thanks.

If u used a heat gun it slide right off

can you leave links for the CAI that you installed. They look amazing!!!

I love the sound of it, could you please send me the part numbers for the defused and the insert? I have the F10 550i and getting ready for the M5 exhaust system saws. Thanks

Great job !! clean,and neat.

What colour code was this RAL 5002

Seriously thats mufflers only? Where can i get cheap new ones

Szuper Bmw f10 550i V8 ☺☺☺💀💀💀👌💪👑✌👊👍💖💖Hungary☺☺☺

How did you get them to be so dark? I tried this on my car and it only brought me to a regular blue color.

Hi can you send Me a link for your setup mufflers n diffuser thanks i have a 2014 550i xdrive

Why post a video then not reply to anybody who took the time to watch it

How many cans of spray did 4 calipers take?

Why the M logo?

Your m logo is upside down on the passenger side. The tricolors always point down. Good idea to clear coat them also

Where did you get the mufflers

What paint did you use? I was thinking plasti dipping Gloss Black. Good idea or no?

What kind of paint did you use to paint the calipers ?

I'm thinking about doing the same to my 550i where did you get the M5 muffler and do you need the exhaust meister? I am in SD, would be curious to see how it sounds in person before taking any decisions

Clean , good work . I just painted my calipers on my f10 to red . They stand out .

Hi, just stumbled upon your video. Car sounds great! One question please: which shop in SD performed the work? Thank you.

You shouldn't run it that hard with a cold engine...!

Do the M5 Comp mufflers require any modification/welding to fit? Do you need the M5 diffuser as well, or would it fit the stock diffuser? Thanks for any help