วีดีโอ

I don't know the laws in India, but I hope the citizens have access to quality air guns. It's good for your health.😀👍 I hope you subscribe, be part of the family.

Thank you FC, 2400kt's can be fun, especially with the LW barrel. I put my 362 away for awhile in pieces, needs a lot of work. The 362, in many instances ,will not empty the valve after each shot. A purging shot is needed between loaded shots to get the best accuracy. Hopefully you decide to subscribe, it would be great to have you onboard!

Thanks a lot Hank. If I could get the wadcutters to shoot straight I might try that. Happy Holidays to you as well my man.

@BriceP.O.I. I hear you family. Looks to me your doing just fine! Cheers!

Thanks AC, glad you like it.

I appreciate the good advice. The dual reg. system accompanied by an Avenge X steel regulator helped quite a bit in this case. Thanks for watching, hopefully you decided to subscribe, it would be great to have you on board!

Hey BYD, nice to see you again! Distance is just 23 yds, will be searching for a pellet that can really stack'em, have plenty to choose from.

A brass 45 degree 1/8" npt fitting, then the foster fitting threads into it. All from amazon. You will need to use thread tape or Permatex thread sealant on both fittings.a.co/d/8pJBR2u Nice of you to stop by PG. Hopefully this helps you get what you need. Hope you decide to subscribe, it would be nice to have you on board!

Thanks for stopping by Hank. The bees seem to be hibernating, danger on hold.

Thank you for stopping by AC, and for the kind words. I was wondering if you've seen the introduction video I put out a couple of weeks ago, that one goes into more detail.

Thank you for the kind words, and welcome, it's nice to have you on board! I took a look at your build and it's fantastic! What a great job you've done with that one. Building one of these Crosmans can be a very therapeutic exercise, not to mention the fun. "Keep putting on the hits".

@BriceP.O.I. thanks for the response buddy!! Keep it up!!! 👏👏

Thanks SG! Good to see you. Happy Holiday.🦃

Thank you very much Hank, if I don't see you, Happy Thanksgiving!🍗

Thanks for the visit TC. Yes, it is the original tube. With the valve pinned at the 4 and 8 positions and limiting the pressure to 2200psi, I do believe there is still a good margin of safety present. Close attention to detail when filling, along with periodic visual inspections of pressure-related parts should keep me in the pink. I'm expecting a shot string profile similar to the 3622 regarding performance. Thank you for bringing this concern to my attention. I had put safety on the back burner for awhile.

Thanks for watching Air gunner. I appreciate your desire to own this beauty, but I don't see myself selling anything at the moment. Though I must admit my wife is definitely on your side.

@@BriceP.O.I. Thanks 🙏 appreciated

Thank you very much FP. Glad you like it. Stop by often!🙂👍

Thanks JS, appreciate you taking a look at it. I pinned the valve under the wood line at the 4/8 position. But those set screws would've looked good, as well as strengthening it up a bit. I have a 362 with the aluminum frame, don't know if I'll use it. Lots of small items to take care of before I get to see the performance side of this one.

@BriceP.O.I. ya I no what you mean. When I build any of my customs if it's not supplied by someone. I build it completely from individual parts it's cheaper and there no left over stock parts. The thing that helps me the most is knowing what can be interchangeable with each model it also allows me to sometimes get the part at a lower price point because some models have the exact same part but is sold at a lower cost because of the model name. Wich doesn't make sense but I notice it's done quite a bit when pricing individual parts. On my 2260 to hpa conversions I use the magnum screws with a discovery valve that I modify similar to the way a boss valve. If you ever looking to make a externally high powered or big bore Crossman the most powerful valve iv used is the Don Catherine discovery power valve. There truly a power house id say the most powerful Crossman/Benjamin valve available for the 22xx series airguns. The build looks very nicely done 💪👌👍💯✌️🫡

@@josephsaucedo8691 Thanks JS. Yeah, I have so many extra parts that I'll never be able to use them all. My pumpers are in bags. I have thought about doing a .25, maybe in the near future. Hey, isn't it fun?

@BriceP.O.I. it sure is. Just to let you know I have 25cal parts that can be built in 2 different ways it can be built to a 25 cal marauder rifel bottle build similar to your 2240 builds or it could also be bult out to a 25cal marauder pistol similar but made from marauder rifel tube and valve assembly parts depending on what you would prefer to build it out to. Just a fyi if interested 💯👌👍🫡✌️

@@josephsaucedo8691 It's definitely something to think about. Barrel as well. Thanks Bro.

I appreciate you taking a look at it Mack. Thanks for the kind words. I'm glad you found your "sweet spot" with your 3622. Mine was only 17 tight shots. Couldn't get a good group either, you got a good one.

You have one? It could be. Thanks for taking a look Hank!

Thank you very much for the visit Hank. That's family!

Right on.

Hello JS. I appreciate the kind words and always value your opinion. This particular 2240 is set up for quick change operations, only to test barrels, probes, springs, valves, etc. Ports are approx. .163- .173". Valve has opened plenum area as well as opened exhaust area. Gives me options for large FPS ranges. Also easy to change regs. by simply changing bottles. This barrel was destined for a lower fps gun, but have since changed my mind. It's not accurate enough to feature in one of my builds. The groups were good at 20yds, but opened up at 25.

@BriceP.O.I. I got ya. If you have a discovery valve top on the valve you can gain more even more plenum if you use the discovery foster fill and cap end. It will have the same functionality it also allows for the stock end cap for a stream line look. With the all the testing you do. You should get a ninja flex regulater it's externally adjustable so you can change the out put psi on the fly. When satisfied you can get the set output reg in place. There awesome for just this type of application and using different weight ammo. We'll worth it for testing and using for different builds and applications all from on tank.💯🫡😉✌️👍

I really like the flex reg idea, I'll have to look into it. It's timely you should speak of the Disco valve top and foster fill end. My current build has these parts installed, but using them in a more traditional way. 🎯

@BriceP.O.I. ha ha if I'd have to guess it's the 2260 to discovery conversion. I also have a few sets in the 2260 conversions . I wish I could give you my email you tube make it difficult and delete it right away id show you mods and builds set ups just remember my username no caps till the next one have a great one 💯🫡👍✌️👌

You might be right.

Hello MGH, nice to see you again. For very granular details of this AVA I would like to give reference to my video 7 months back titled " Air Venturi Avenger .22 custom unit. I think you'll enjoy it. Lots of info on this one.

@ - thanks for the reference. I’ll check it out.

T Y

Thanks BYD, I appreciate your words of praise. 😁👌

Ha Ha. Hello MP, no not a beekeeper. The mosquitoes in North Carolina are ravenous. The Asian Tiger and the largest in the world Gallinipper are always waiting to have a meal. Are you subscribed? It would be nice to have you on board! 🦟☹

I think I'll try those, could always use a good pellet showdown. Next time I'm shopping on Pyramyd I'll pickup a tin of each. Thanks AG4L.

thanks for the tip LEAD HEADS are you not making vids anymore?

@@BackyardDispatcher I've been super busy raising 4 kids, ages 4-6-9-&15 years old. I'm working as much as possible to make ends meet and just can't find the time to shoot. I got a new AIRFORCE ESCAPE SPECIAL EDITION TON JONES model number 79 of only 100 made with the special power valve and a few other goodies. I haven't even shot it yet. I'll be running 38 to 40gr. 22 cal slugs. The AIRGUN is about 5 times louder than a .22lr ... I got one of BUCKRAILS new modular suppressor kits that I can add as many baffel sections as needed, so hopefully it will tame up the BEAST. I'm going to try and do Rick Reims 500 yard challenge with it, it's got more power than needed to do it, so I'll get it done.

@@AIRGUN4LIFE heck yeah I'd say you are busy I have always like the Airforce Texan , I will be on the lookout for when you drop that video

Yes, possibly a temporary setup due to the gauge letting go on the 100cc thin cylinder. Put a 1/16" NPT plug in it, ready to go, thought I'd enjoy the extra shots this one provides for a week or two. Hey, I talked about that in the video Have you subscribed? I'd love to have you on board!

@@BriceP.O.I. yes sir, I'm subscribed

@@AIRGUN4LIFE 🙂👍

I agree, even though the valve is pinned at the 3 and 9 o'clock positions, I've never been to thrilled with the 1900psi. The original use case for this unit was 0-40yds, in the near future I plan on doing some performance tests with lower reg. settings.

😆👍

Hey BYD. The barrel is Lothar Walther at 14.6". 100cc cyl filled to 3500psi and regulated to 1640psi.Thanks for the visit AG brother.

Rust o leum camouflage , also gray primer, all flat. At the time, all I could find was semi gloss clearcoat. 🎨

@@BriceP.O.I. I am tempted to use Krylon plastic spray paint Thanks

I've used Krylon on other projects in the past with great results.

@@BriceP.O.I. Krylon clear plastic paint Satin over yours 👍

I no longer see an inexpensive way to build an Avenger similar to this one. AE Swede is closed presently. There is Hajimoto or Terminador Industries available for kits, but they're very expensive when compared to Swede. I would wait to see if he re-opens his site. 😐

Might try 8.44's experimenting with speeds.

Thanks AG4L, I appreciate that.

I agree, need to be able to see better. Maybe Christmas will be good to me.🎅

I think Cvlife is ok I use them vs Powerline way better

@@BackyardDispatcher A UTG BUG BUSTER 3-12x44 sfp is so good for the paper. Both great for close up and definitely past 100 yards. Everything about them is top notch, the turrets are as good as my high dollar scopes. I have not one thing that I can complain about.

Hello Mack, I put a scale to it, came in at .90". 🧐👌🥳

Hello kluper, I've checked around, AE Swede website is still there, but not accessible. It says "coming soon" so maybe he'll re-open it in the near future. That's where you'll be able to get the adapter, plug and bottle band. Regulator and bottle on ebay. If he again offers the adapters for sale, I'll make a video addressing the conversion and parts needed. Thanks for watching!

@@BriceP.O.I. I found it in Canada 260 for the hole setup!!

360 cc tank Carbon love it!

Great for you kluper! That's amazing that you found it in Canada. Isn't it illegal there?

I agree, the barrel comes first, then the gun. Crosman never really tried to improve their barrels, and for over 2 years the LW's weren't available. All .22's are still loose, even when sending 5.55mm head sized pellets through. That's unacceptable. The Chinese companies have it figured out, even though the chokes aren't very consistent either in length or weight. Still the chances you get a good shooter are very high. Thanks for watching MQ!

Hello ACS, thank you for watching. The Bottle band is from AE Swede, unfortunately no longer in business. More info is available in my video titled " Air Venturi Avenger .22 Custom Unit" from 6 months back. Many bottle bands are available on Ebay from Terminador Industries and others.

No lathe. When I need to, I make jigs from wood and use clamps and hand drills for the rotation. Thank goodness I'm not in a hurry. Thanks bro

Thanks BYD, I thought about that when I realized I had a different Bi pod mounted on the gun.😂👍