วีดีโอ

Easiest tutorial on configuring InterVlan routing on Cisco multi-layer switch

Switch(config)#ip default-gateway 192.168.1.1 Switch(config)#do wr Building configuration... [OK] Enter configuration commands, one per line. End with CNTL/Z. 1(config)#access-list 1 permit 192.168.1.0 0.0.0.255 1(config)#router eigrp 1 1(config-router)#eigrp router-id 1.1.1.1 1(config-router)#network 0.0.0.0 0.0.0.0 1(config-router)#exit 1(config)#do sh ip int br Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0/0 192.168.1.1 YES manual up up GigabitEthernet0/0/1 200.1.1.1 YES manual up up Vlan1 unassigned YES unset administratively down down 1(config)#int g0/0/0 1(config-if)#description link to lan 1(config-if)#exit 1(config)#int g0/0/1 1(config-if)#description link to WAN 1(config-if)#exit 1(config)#ip nat inside source static 192.168.1.2 200.1.1.3 1(config)#ip nat inside source static 192.168.1.3 200.1.1.4 1(config)#ip nat inside source static 192.168.1.4 200.1.1.5 1(config)#int g0/0/1 1(config-if)#ip nat outside 1(config-if)#exit 1(config)#int g0/0/0 1(config-if)#ip nat inside 1(config-if)#exit 1(config)# ISP#conf ISP#configure t Enter configuration commands, one per line. End with CNTL/Z. ISP(config)#int g0/0/0 ISP(config-if)#description link to WAN ISP(config-if)#EXIT ISP(config)#int g0/0/1 ISP(config-if)#description link to LAN ISP(config-if)#exit ISP(config)#router eigrp 1 ISP(config-router)#eigrp router-id 2.2.2.2 ISP(config-router)#network 0.0.0.0 0.0.0.0 ISP(config-router)# %DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 200.1.1.1 (GigabitEthernet0/0/0) is up: new adjacency ISP(config-router)#exit ISP(config)#do wr Building configuration... [OK] 1>en 1#show ip nat translation Pro Inside global Inside local Outside local Outside global icmp 200.1.1.3:1 192.168.1.2:1 170.1.1.2:1 170.1.1.2:1 icmp 200.1.1.3:2 192.168.1.2:2 170.1.1.2:2 170.1.1.2:2 icmp 200.1.1.3:3 192.168.1.2:3 170.1.1.2:3 170.1.1.2:3 icmp 200.1.1.3:4 192.168.1.2:4 170.1.1.2:4 170.1.1.2:4 icmp 200.1.1.3:5 192.168.1.2:5 170.1.1.2:5 170.1.1.2:5 icmp 200.1.1.3:6 192.168.1.2:6 170.1.1.2:6 170.1.1.2:6 icmp 200.1.1.3:7 192.168.1.2:7 170.1.1.2:7 170.1.1.2:7 icmp 200.1.1.3:8 192.168.1.2:8 170.1.1.2:8 170.1.1.2:8 icmp 200.1.1.4:2 192.168.1.3:2 170.1.1.2:2 170.1.1.2:2 icmp 200.1.1.4:3 192.168.1.3:3 170.1.1.2:3 170.1.1.2:3 icmp 200.1.1.4:4 192.168.1.3:4 170.1.1.2:4 170.1.1.2:4 icmp 200.1.1.4:5 192.168.1.3:5 170.1.1.2:5 170.1.1.2:5 icmp 200.1.1.4:6 192.168.1.3:6 170.1.1.2:6 170.1.1.2:6 icmp 200.1.1.4:7 192.168.1.3:7 170.1.1.2:7 170.1.1.2:7 icmp 200.1.1.4:8 192.168.1.3:8 170.1.1.2:8 170.1.1.2:8 --- 200.1.1.3 192.168.1.2 --- --- --- 200.1.1.4 192.168.1.3 --- --- --- 200.1.1.5 192.168.1.4 --- --- tcp 200.1.1.5:1027 192.168.1.4:1027 170.1.1.2:80 170.1.1.2:80 1#show ip nat statistics Total translations: 4 (3 static, 1 dynamic, 1 extended) Outside Interfaces: GigabitEthernet0/0/1 Inside Interfaces: GigabitEthernet0/0/0 Hits: 31 Misses: 23 Expired translations: 22 Dynamic mappings: Switch> Switch>en Switch#conf Switch#configure t Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#host SW1 SW1(config)#int vlan 1 SW1(config-if)#ip add 192.168.1.254 255.255.255.0 SW1(config-if)#no shut SW1(config-if)# %LINK-5-CHANGED: Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up SW1(config-if)#exit SW1(config)#ip default-gateway 192.168.1.1 SW1(config)#do wr Building configuration... [OK] 1#show ip nat translation Pro Inside global Inside local Outside local Outside global icmp 200.1.1.5:10 192.168.1.4:10 170.1.1.2:10 170.1.1.2:10 icmp 200.1.1.5:11 192.168.1.4:11 170.1.1.2:11 170.1.1.2:11 icmp 200.1.1.5:12 192.168.1.4:12 170.1.1.2:12 170.1.1.2:12 icmp 200.1.1.5:9 192.168.1.4:9 170.1.1.2:9 170.1.1.2:9 --- 200.1.1.3 192.168.1.2 --- --- --- 200.1.1.4 192.168.1.3 --- --- --- 200.1.1.5 192.168.1.4 --- --- tcp 200.1.1.4:1025 192.168.1.3:1025 170.1.1.2:80 170.1.1.2:80 tcp 200.1.1.5:1025 192.168.1.4:1025 170.1.1.2:80 170.1.1.2:80 tcp 200.1.1.5:1026 192.168.1.4:1026 170.1.1.2:80 170.1.1.2:80 1#show ip nat statistics Total translations: 6 (3 static, 3 dynamic, 3 extended) Outside Interfaces: GigabitEthernet0/0/1 Inside Interfaces: GigabitEthernet0/0/0 Hits: 38 Misses: 23 Expired translations: 20 Dynamic mappings:

Switch> Switch>EN Switch#conf Switch#configure t Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#int vlan 1 Switch(config-if)#ip add 192.168.0.2 255.255.255.0 Switch(config-if)#no shut Switch(config-if)# %LINK-5-CHANGED: Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up Switch(config-if)#exit Switch(config)#ip default-gateway 192.168.0.1 Switch(config)#do wr Building configuration... [OK] Switch(config)#host SW1 SW1(config)#END SW1# %SYS-5-CONFIG_I: Configured from console by console SW1#WR Building configuration... [OK] SW1#SH IP INT BR Interface IP-Address OK? Method Status Protocol FastEthernet0/1 unassigned YES manual up up FastEthernet0/2 unassigned YES manual up up FastEthernet0/3 unassigned YES manual down down FastEthernet0/4 unassigned YES manual down down FastEthernet0/5 unassigned YES manual down down FastEthernet0/6 unassigned YES manual down down FastEthernet0/7 unassigned YES manual down down FastEthernet0/8 unassigned YES manual down down FastEthernet0/9 unassigned YES manual down down FastEthernet0/10 unassigned YES manual down down FastEthernet0/11 unassigned YES manual down down FastEthernet0/12 unassigned YES manual down down FastEthernet0/13 unassigned YES manual down down FastEthernet0/14 unassigned YES manual down down FastEthernet0/15 unassigned YES manual down down FastEthernet0/16 unassigned YES manual down down FastEthernet0/17 unassigned YES manual down down FastEthernet0/18 unassigned YES manual down down FastEthernet0/19 unassigned YES manual down down FastEthernet0/20 unassigned YES manual down down FastEthernet0/21 unassigned YES manual down down FastEthernet0/22 unassigned YES manual down down FastEthernet0/23 unassigned YES manual down down FastEthernet0/24 unassigned YES manual down down GigabitEthernet0/1 unassigned YES manual down down GigabitEthernet0/2 unassigned YES manual down down Vlan1 192.168.0.2 YES manual up SW1#SH RUN Building configuration... Current configuration : 1123 bytes ! version 15.0 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption ! hostname SW1 ! ! ! ! ! ! spanning-tree mode pvst spanning-tree extend system-id ! interface FastEthernet0/1 ! interface FastEthernet0/2 ! interface FastEthernet0/3 ! interface FastEthernet0/4 ! interface FastEthernet0/5 ! interface FastEthernet0/6 ! interface FastEthernet0/7 ! interface FastEthernet0/8 ! interface FastEthernet0/9 ! interface FastEthernet0/10 ! interface FastEthernet0/11 ! interface FastEthernet0/12 ! interface FastEthernet0/13 ! interface FastEthernet0/14 ! interface FastEthernet0/15 ! interface FastEthernet0/16 ! interface FastEthernet0/17 ! interface FastEthernet0/18 ! interface FastEthernet0/19 ! interface FastEthernet0/20 ! interface FastEthernet0/21 ! interface FastEthernet0/22 ! interface FastEthernet0/23 ! interface FastEthernet0/24 ! interface GigabitEthernet0/1 ! interface GigabitEthernet0/2 ! interface Vlan1 ip address 192.168.0.2 255.255.255.0 ! ip default-gateway 192.168.0.1 ! ! ! ! line con 0 ! line vty 0 4 login line vty 5 15 login ! ! ! ! end Router>EN Router#CONF Router#CONFigure T Enter configuration commands, one per line. End with CNTL/Z. Router(config)#HOST R1 R1(config)#INT G0/0/0 R1(config-if)#description Link to LAN R1(config-if)#ip add 192.168.0.1 255.255.255.0 R1(config-if)#no shut R1(config-if)# %LINK-5-CHANGED: Interface GigabitEthernet0/0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0/0, changed state to up R1(config-if)#exit R1(config)#INT G0/0/1 R1(config-if)#description Link to WAN R1(config-if)#ip add 192.169.0.1 255.255.255.0 R1(config-if)#NO SHUT R1(config-if)# %LINK-5-CHANGED: Interface GigabitEthernet0/0/1, changed state to up R1(config-if)#exit R1(config)#router eigrp 1 R1(config-router)#eigrp router-id 1.1.1.1 R1(config-router)#network 0.0.0.0 0.0.0.0 R1(config-router)#end R1# %SYS-5-CONFIG_I: Configured from console by console R1#wr Building configuration... [OK] R1# R2(config-if)#exit R2(config)#int g0/0/1 R2(config-if)#description Link to WAN R2(config-if)#ip add 192.169.0.2 255.255.255.0 R2(config-if)#NO SHUT R2(config-if)# %LINK-5-CHANGED: Interface GigabitEthernet0/0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0/1, changed state to up R2(config-if)#exit R2(config)#router eigrp 1 R2(config-router)#network 0.0.0.0 0.0.0 ^ % Invalid input detected at '^' marker. R2(config-router)#eigrp router-id 2.2.2.2 R2(config-router)#network 0.0.0.0 0.0.0.0 R2(config-router)# %DUAL-5-NBRCHANGE: IP-EIGRP 1: Neighbor 192.169.0.1 (GigabitEthernet0/0/1) is up: new adjacency R2(config-router)#exit Switch>EN Switch#CONF Switch#CONFigure T Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#HOST sw2 sw2(config)#INT VLAN 1 sw2(config-if)#IP ADD 172.16.0.2 255.255.0.0 sw2(config-if)#NO SHUT sw2(config-if)# %LINK-5-CHANGED: Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up sw2(config-if)#EXIT sw2(config)#IP DEFAULT-GATEWAY 172.16.0.1 sw2(config)#do wr Building configuration... [OK] sw2(config)# R2(config)#ip nat inside source static tcp 172.16.0.5 80 192.169.0.2 80 R2(config)#int g0/0/0 R2(config-if)#ip nat inside R2(config-if)#exit R2(config)#int g0/0/1 R2(config-if)#ip nat outside R2(config-if)#exit

Switch>en Switch#conf Switch#configure t Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#hostname Catalyst Catalyst(config)#enable secret Cisco Catalyst(config)#username Arklow password 2960 Catalyst(config)#line vty 0 1 Catalyst(config-line)#login local Catalyst(config-line)#transport input telnet Catalyst(config-line)#end Catalyst# %SYS-5-CONFIG_I: Configured from console by console Catalyst#wr Building configuration... [OK] Catalyst(config)#int vlan 1 Catalyst(config-if)#ip 192.168.0.2 255.255.255.0 ^ % Invalid input detected at '^' marker. Catalyst(config-if)#ip address 192.168.0.2 255.255.255.0 Catalyst(config-if)#no shut Catalyst(config-if)# %LINK-5-CHANGED: Interface Vlan1, changed state to up Catalyst(config-if)#exit Catalyst(config)#do wr Building configuration... [OK]

Nice

Switch#show clock detail *19:2:19.559 UTC Tue Aug 15 2023 Time source is hardware calendar

skillsforall.com/resources/lab-downloads?courseLang=en-US

Carry on bro

community.cisco.com/t5/switching/what-is-the-maximum-number-of-physical-link-we-can-bind-to-a/td-p/2511882

www.cisco.com/c/en/us/support/docs/switches/catalyst-3750-series-switches/69979-cross-stack-etherchannel.html

en.wikipedia.org/wiki/EtherChannel

www.sunsetlearning.com/etherchannel-lacp-pagp-static-protocols/

www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3750x_3560x/software/release/12-2_55_se/configuration/guide/3750xscg.pdf

www.cisco.com/c/en/us/support/docs/lan-switching/etherchannel/22422-144.html

www.cisco.com/c/en/us/support/docs/lan-switching/etherchannel/12023-4.html

www.ciscopress.com/articles/article.asp?p=2348266&seqNum=3

community.cisco.com/t5/switching/static-and-dynamic-ether-channel/td-p/2217335

sWITCH-2#SHOW ETHERCHANNEL Channel-group listing: ---------------------- Group: 2 ---------- Group state = L2 Ports: 2 Maxports = 16 Port-channels: 1 Max Port-channels = 16 Protocol: LACP sWITCH-2# sWITCH-2# sWITCH-2# sWITCH-2# sWITCH-2#SHOW ETHERCHANNEL SUMMARY Flags: D - down P - in port-channel I - stand-alone s - suspended H - Hot-standby (LACP only) R - Layer3 S - Layer2 U - in use f - failed to allocate aggregator u - unsuitable for bundling w - waiting to be aggregated d - default port Number of channel-groups in use: 1 Number of aggregators: 1 Group Port-channel Protocol Ports ------+-------------+-----------+---------------------------------------------- 2 Po2(SU) LACP Gig0/1(P) Gig0/2(P) sWITCH-2# sWITCH-2#SHOW ETHERCHANNEL ? load-balance Load-balance/frame-distribution scheme among ports in port-channel port-channel Port-channel information summary One-line summary per channel-group <cr> sWITCH-2#SHOW ETHERCHANNEL Channel-group listing: ---------------------- Group: 2 ---------- Group state = L2 Ports: 2 Maxports = 16 Port-channels: 1 Max Port-channels = 16 Protocol: LACP sWITCH-2#SHOW ETHERCHANNEL LOAD-BALANCE EtherChannel Load-Balancing Operational State (src-mac): Non-IP: Source MAC address IPv4: Source MAC address IPv6: Source MAC address sWITCH-2#SHOW ETHERCHANNEL PORT-CHANNEL Channel-group listing: ---------------------- Group: 2 ---------- Port-channels in the group: --------------------------- Port-channel: Po2 (Primary Aggregator) ------------ Age of the Port-channel = 00d:00h:02m:46s Logical slot/port = 2/2 Number of ports = 2 GC = 0x00000000 HotStandBy port = null Port state = Port-channel Protocol = LACP Port Security = Disabled Ports in the Port-channel: Index Load Port EC state No of bits ------+------+------+------------------+----------- 0 00 Gig0/2 Passive 0 0 00 Gig0/1 Passive 0 Time since last port bundled: 00d:00h:02m:41s Gig0/1

www.cisco.com/c/en/us/td/docs/ios/12_2sb/feature/guide/gigeth.html

SW2#SHOW ETHERCHANNEL SUMMARY Flags: D - down P - in port-channel I - stand-alone s - suspended H - Hot-standby (LACP only) R - Layer3 S - Layer2 U - in use f - failed to allocate aggregator u - unsuitable for bundling w - waiting to be aggregated d - default port Number of channel-groups in use: 1 Number of aggregators: 1 Group Port-channel Protocol Ports ------+-------------+-----------+---------------------------------------------- 1 Po1(SU) PAgP Fa0/1(P) Fa0/2(P) Fa0/4(P) SW2#SHOW ETHERCHANNEL Channel-group listing: ---------------------- Group: 1 ---------- Group state = L2 Ports: 3 Maxports = 8 Port-channels: 1 Max Portchannels = 1 Protocol: PAGP SW1#SHOW ETHERCHANNEL ? load-balance Load-balance/frame-distribution scheme among ports in port-channel port-channel Port-channel information summary One-line summary per channel-group SW2#SHOW ETHERCHANNEL PORT-CHANNEL Channel-group listing: ---------------------- Group: 1 ---------- Port-channels in the group: --------------------------- Port-channel: Po1 ------------ Age of the Port-channel = 00d:00h:05m:25s Logical slot/port = 2/1 Number of ports = 3 GC = 0x00000000 HotStandBy port = null Port state = Port-channel Protocol = PAGP Port Security = Disabled Ports in the Port-channel: Index Load Port EC state No of bits ------+------+------+------------------+----------- 0 00 Fa0/2 Automatic 0 0 00 Fa0/1 Automatic 0 0 00 Fa0/4 Automatic 0 Time since last port bundled: 00d:00h:05m:08s Fa0/4 SW1#SHOW ETHERCHANNEL LOAD-BALANCE EtherChannel Load-Balancing Operational State (src-mac): Non-IP: Source MAC address IPv4: Source MAC address IPv6: Source MAC add

learningnetwork.cisco.com/s/article/fundamentals-of-eigrp-case-study-1

www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/16406-eigrp-toc.html

www.certificationkits.com/cisco-certification/cisco-ccna-640-802-exam-certification-guide/cisco-ccna-eigrp-part-i/

community.cisco.com/t5/switching/switchport-trunk-allowed-vlan-remove-1607/td-p/1496171

Switch> Switch>EN Switch#CONF Switch#CONFigure T Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#INT RANGE F0/5-22, F0/24 Switch(config-if-range)#SHUT %LINK-5-CHANGED: Interface FastEthernet0/5, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/6, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/7, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/8, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/9, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/10, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/11, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/12, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/13, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/14, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/15, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/16, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/17, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/18, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/19, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/20, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/21, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/22, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/24, changed state to administratively down Switch(config-if-range)#EXIT Switch(config)#vlan 2 Switch(config-vlan)#name HR Switch(config-vlan)#vlan 3 Switch(config-vlan)#name Management Switch(config-vlan)#exit Switch(config)#int range f0/1-2 Switch(config-if-range)#switchport mode trunk Switch(config-if-range)# %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up Switch(config-if-range)#no switchport mode trunk Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport nonegotiate Switch(config-if-range)#switchport access vlan 2 Switch(config-if-range)#exit Switch(config)#int range f0/3-4 Switch(config-if-range)#switchport nonegotiate Command rejected: Conflict between 'nonegotiate' and 'dynamic' status. Command rejected: Conflict between 'nonegotiate' and 'dynamic' status. Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport nonegotiate Switch(config-if-range)#switchport access vlan 3 Switch(config-if-range)#exit Switch(config)#int g0/1 Switch(config-if)#switchport mode trunk Switch(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up Switch(config-if)#switchport trunk encapsulation dot1q ^ % Invalid input detected at '^' marker. Switch(config-if)#switchport ? access Set access mode characteristics of the interface mode Set trunking mode of the interface nonegotiate Device will not engage in negotiation protocol on this interface port-security Security related command priority Set appliance 802.1p priority protected Configure an interface to be a protected port trunk Set trunking characteristics of the interface voice Voice appliance attributes Switch(config-if)#switchport trunk ? allowed Set allowed VLAN characteristics when interface is in trunking mode native Set trunking native characteristics when interface is in trunking mode Switch(config-if)#switchport nonegotiate Switch(config-if)#exit Switch(config)#host sw1 sw1(config)#end sw1# %SYS-5-CONFIG_I: Configured from console by console sw1#show vlan VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10, Fa0/11, Fa0/12 Fa0/13, Fa0/14, Fa0/15, Fa0/16 Fa0/17, Fa0/18, Fa0/19, Fa0/20 Fa0/21, Fa0/22, Fa0/23, Fa0/24 Gig0/2 2 HR active Fa0/1, Fa0/2 3 Management active Fa0/3, Fa0/4 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active Switch>EN Switch#CONF Switch#CONFigure T Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#HOST sw2 sw2(config)#INT G0/1 sw2(config-if)#SWITCHPORT MODE TRUNK sw2(config-if)# %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to up sw2(config-if)#SWITCHPORT NONEGOTIATE sw2(config-if)#exit sw2(config)#vlan 2 sw2(config-vlan)#name HR sw2(config-vlan)#vlan 3 sw2(config-vlan)#mangement ^ % Invalid input detected at '^' marker. sw2(config-vlan)#name mangement sw2(config-vlan)#exit sw2(config)#int range f0/6-24 sw2(config-if-range)#shut %LINK-5-CHANGED: Interface FastEthernet0/6, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/7, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/8, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/9, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/10, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/11, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/12, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/13, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/14, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/15, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/16, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/17, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/18, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/19, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/20, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/21, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/22, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/23, changed state to administratively down %LINK-5-CHANGED: Interface FastEthernet0/24, changed state to administratively down sw2(config-if-range)# sw2(config-if-range)#exit sw2(config)#int range f0/1-2 sw2(config-if-range)#switchport mode access sw2(config-if-range)#switchport access vlan 2 sw2(config-if-range)#int range f0/3-4 sw2(config-if-range)#switchport mode access sw2(config-if-range)#switchport access vlan 3 sw2(config-if-range)#end sw2# %SYS-5-CONFIG_I: Configured from console by console sw2#wr Building configuration... [OK] sw2#