วีดีโอ

Interesting solution. Where can I order such a set?

Whatd ya actually do?

So you just bent that tab back into alignment?

Man I’m having the same issues with my evo as well

I've had a 3rd and 4th gear grind for a bit now... idk whether to buy a new Trans or rebuild...

Looks exactly like a kseries trans. Definitely gonna learn to build these.

Is the valve not rated for 100% duty cycle? Seems like they would design the kit to have the valve just stay open with the key on/ close with key off and avoid the manual switch.

Its the reverse and 5th gear shift fork shaft. You have it upside down.

Any luck fixing this???

Shep trans, TRE, or Jacks transmission..............send it there is my advice.

Ford should be forced to cover every single one of these until the end of time. It was obvioulsy a defective design from the get go. If Toyota and Honda can make them last 300K then there is no excuse for Ford and everyone else. Hyundai!

*anyone watching* please be carful doing this you need to put a towel under each valve stem to insure it doesn't bend valves hammering out the keepers, springs and retainers

A description of the process what you did here would great and very helpful. Noticed you have some Christian content on your channel also. Are you a Christian?

I'm always amazed at how much money people spend on vehicles that don't work propely then spend even more on aftermarket parts... How about just buying a quality vehicle to start with?

Nicely done. Quality and editing are solid. Good job man

From the sound I could tell it’s got lot of HP

Just hire an illegal to hold it there while you drive, there are millions of them

Did your 3.5 knock a little as well?

For 5 more dollars you could buy a good oil filter

that sounds like someone whos gone 50mph and slapped it in reverse 😂

Where did you find the Manuals im having problems with the reverse not engaging and i thing the te “wing Piace” dont know the name i want to se one

Do you have links for all the parts you have used?

You weren't using Amsoil were you? Would have lessened your chances of this happening!

Thank you!

Did you figure out the o-ring size? After more testing, mine is sealing only sometimes, like yours. I would like to put a bigger o-ring on there.

THAT SIR IS A NASTY CRACK... darn you should better check your floorboards make sure they are ok though (Rafa)

How to disable the airbag and steering ribbon?

Part number?

Mine was leaking at the top, some RTV under the cap solved it. Mine is also leaking at the valve itself, and it seems like it's only leaking under push mode (pressure is opening the valve) but I'm not positive. Maybe just a bad o-ring? The o-ring is present. Unfortunately their website is gone now so I can't find detailed info about how to set it up in pull mode.

Can bikes be on when tilt down???

JP's bullshit anti-Marxist, anti-Socialist, anti-woke ravings befit his status as an alt-right partisan hack. The only significant difference between JP & Tucker Carlson is the former's elitist vocabulary. TC's audience wouldn't understand it. But both push the same hot buttons for their demographics.

Mine rattles at 950 to 1100 rpm since 40k 200k now

It make any difference sense you not using a motorcraft filter?

@flatlinelancer any updates? How many more miles?

Problem is that it's a 3.5. Ecobusted. In my opinion.

hey hi you know how do diagnosti for check more easy all ?

How often do you need to add air to the masterlube kit?

What mm is the socket?

My roomba620 did that sound

That’s a really helpful tip, thanks man. But also I think you can pull apart the middle of that rubber boot in the engine bay and unscrew it from there if need.

That’s a rod 😦

My 2015 f150 3.5 EcoBoost developed a rattle. instead of bringing it in I did some troubleshooting. Thankfully In my case it was failed clamps on the muffler heat shield. Easy fix!

I have one of these and they say that pull mode closes fast vs push mode it’s slower to seal under boost. Are you still using it?

Where your store located?

Is the 5.0 engine any good?

Great video, how is the issue now that it has been a few months and we are in summer. I am in Houston and plan to do this as well. Would you share what model kit you purchased? Thanks for the video. Craig in Houston

Does adding this extra oil affect the oil level on the dipstick?

you should do a follow up on the kit on how its been working?

Have u done anything for a switch? My wife drives our expedition all the time and to get her to flip a switch before starting the vehicle is going to throw her for a loop and if i can make if fool proof thats deff what i need to do.

Last Ford I'll ever own because of this. Why not but a vehicle that last and not a POS Ford.