- 67
- 83 009
Classic junk
United States
เข้าร่วมเมื่อ 25 เม.ย. 2024
I have several projects that my dad and I have accumulated over the years. We together have about 10 vehicles ranging from an old muscle car, a military truck, to more modern jeeps. And always looking for more projects.
Gm 3800 V6 Replacing coolant elbows
Replacing the coolant elbows on a 2001 Pontiac grand prix with a 3800 v6
มุมมอง: 9
วีดีโอ
Jeeps playing in the snow! 5.9 /m715
มุมมอง 22หลายเดือนก่อน
Pulling out the 5.9 grand Cherokee limited and the 1967 kaiser m715
Easy step by step how to change front brake pads
มุมมอง 212 หลายเดือนก่อน
Easy step by step how to change front brake pads
Prepping 05+ ford super duty front axle for leaf springs/truss with a grinder Sawzall and a hammer
มุมมอง 622 หลายเดือนก่อน
Prepping 05 ford super duty front axle for leaf springs/truss with a grinder Sawzall and a hammer
cheap Amazon welding cart because I'm cheap
มุมมอง 123 หลายเดือนก่อน
cheap Amazon welding cart because I'm cheap
Swapping super duty axles on to 1967 kaiser m715 (rear axle)
มุมมอง 1163 หลายเดือนก่อน
Swapping super duty axles on to 1967 kaiser m715 (rear axle)
rear rotor replacement on 08 gmc 2500 hd
มุมมอง 83 หลายเดือนก่อน
rear rotor replacement on 08 gmc 2500 hd
aar cuda, kaiser m715, and a Hudson are a few projects i have
มุมมอง 157 หลายเดือนก่อน
aar cuda, kaiser m715, and a Hudson are a few projects i have
how to remove any broke off crank position sensor @Classicjunk-ue6ep
มุมมอง 857 หลายเดือนก่อน
how to remove any broke off crank position sensor @Classicjunk-ue6ep
This is the only complaint I had with the one I owe but once I replaced this elbow with a better one had no more problems
Yeah I've done a few of these and there always the same completely falling apart
I can't believe that haven't been converted To metal yet. Don't forget the ones on the firewall for the heater core.🎉🎉🎉
I'm check into that
Reminds me of the plastic fuel elbows on Chevy cavalry right on top of the motor 😂
Yeah even the Pontiac has them to
Did you rip one mid video?😂
There was a little guy in there 😆
I got a 13 grand Cherokee but shit that’s what’s good right there😊
Yeah the old girl has some power still
I can dig it.
Thank you
Clean that shit up dude
For sure dude
Get a wire wheel man…
That's for sure
Put the camera down. Get a wire wheel. Do it right.
😆 I did shortly after she looks a lot nicer
Not really the most intelligent person using an angle grinder while holding a camera in the other hand.
The grinder has a grip and a finger trigger not like a traditional grinder
What 😂 thats new wym looks shiny to me 😂😅
Lol
The fart 😂
Yeah she's a turd i figured a fart was proper 😆
I rember that container on the shelf
Back in the day
Tell your apprentice to sharpen his beaver
Dull beaver 😆
I want to contact you because I have an M715 car and I have some questions about it
Hi there and what would be your questions?
Take them and throw them across the street and yell at the top of your lungs!
Looks like ur ready for rotors also
Ready for a new car 😆
Negative. 💯% incorrect. A true technician will clean the caliper brackets out so that the pads will fit and slide freely as they should. Grinding the paint and enamel off the brake pad will only ensure that it is going to rust into the bracket seizing up.
This is the rust belt I know all about rust 😆
Why not use the m715 axles?
Very little after-market for them, it's a very large 6 bolt, bolt pattern. I think only 2 after-market rims to choose from. And they are a split rim stock. Same for gears as far as I know very little aftermarket. They only go 45mph stock. This gives me better driveability and much larger selection of after-market parts. Newer axles are much stronger also.
@Classicjunk-ue6ep I see your points. Somebody will probably want the stock ones if you didn't plan on keeping them. Hate to see them scrapped.
I would cry
Lol luckily I was able to just cut it off
Don’t threaten me with a good time
😆 check out the full video I put together. I'm making more progress on the rest of it
What popped off😢
😆
The gap on that thing too!! Nothing like A big gappy wet bish
You'll have fun with it, and get a lotta thumbs up. I have people stop to take pics of mine all the time.
They are really cool. I've always wanted one very tough looking!
WITH A CHEVY DRIVE TRAIN BE A GREAT TRUCK
I'm working on it. Ford axles and Chevy drivetrain
@@Classicjunk-ue6ep AWESOME
And this video was made 6 minutes ago
Yes
Looking like Trevor’s car in gta five
They definitely modeled it after this truck
Yea that’s a project
Very much so
Project
Yes it is
I have that car.
One of my favorites. I'm hoping to pick this one up
Nice love to have that.
I'm hoping to be able to make a deal on this one
What are you thinking on the green Chevy